1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
| /*
| * Licensed to the Apache Software Foundation (ASF) under one
| * or more contributor license agreements. See the NOTICE file
| * distributed with this work for additional information
| * regarding copyright ownership. The ASF licenses this file
| * to you under the Apache License, Version 2.0 (the
| * "License"); you may not use this file except in compliance
| * with the License. You may obtain a copy of the License at
| *
| * http://www.apache.org/licenses/LICENSE-2.0
| *
| * Unless required by applicable law or agreed to in writing,
| * software distributed under the License is distributed on an
| * "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
| * KIND, either express or implied. See the License for the
| * specific language governing permissions and limitations
| * under the License.
| */
|
| #ifndef __MCU_MCU_H_
| #define __MCU_MCU_H_
|
| #ifdef __cplusplus
| extern "C" {
| #endif
|
| /*
| * Defines for naming GPIOs. NOTE: the nordic chip docs use numeric labels for
| * ports. Port A corresponds to Port 0, B to 1, etc. The nrf52832 has only one
| * port and thus uses pins 0 - 31. The nrf52840 has two ports but Port 1 only
| * has 16 pins.
| */
| #define MCU_GPIO_PORTA(pin) ((0 * 16) + (pin))
| #define MCU_GPIO_PORTB(pin) ((1 * 16) + (pin))
|
| #if NRF52
|
| #define MCU_SYSVIEW_INTERRUPTS \
| "I#1=Reset,I#2=MNI,I#3=HardFault,I#4=MemoryMgmt,I#5=BusFault,I#6=UsageFault," \
| "I#11=SVCall,I#12=DebugMonitor,I#14=PendSV,I#15=SysTick," \
| "I#16=POWER_CLOCK,I#17=RADIO,I#18=UARTE0_UART0,I#19=SPIx0_TWIx0," \
| "I#20=SPIx1_TWIx1,I#21=NFCT,I#22=GPIOTE,I#23=SAADC," \
| "I#24=TIMER0,I#25=TIMER1,I#26=TIMER2,I#27=RTC0,I#28=TEMP,I#29=RNG,I#30=ECB," \
| "I#31=CCM_AAR,I#32=WDT,I#33=RTC1,I#34=QDEC,I#35=COMP_LPCOMP,I#36=SWI0_EGU0," \
| "I#37=SWI1_EGU1,I#38=SWI2_EGU2,I#39=SWI3_EGU3,I#40=SWI4_EGU4,I#41=SWI5_EGU5," \
| "I#42=TIMER3,I#43=TIMER4,I#44=PWM0,I#45=PDM,I#48=MWU,I#49=PWM1,I#50=PWM2," \
| "I#51=SPIx2,I#52=RTC2,I#53=I2S,I#54=FPU"
|
| #elif NRF52840_XXAA
|
| #define MCU_SYSVIEW_INTERRUPTS \
| "I#1=Reset,I#2=MNI,I#3=HardFault,I#4=MemoryMgmt,I#5=BusFault,I#6=UsageFault," \
| "I#11=SVCall,I#12=DebugMonitor,I#14=PendSV,I#15=SysTick," \
| "I#16=POWER_CLOCK,I#17=RADIO,I#18=UARTE0_UART0,I#19=SPIx0_TWIx0," \
| "I#20=SPIx1_TWIx1,I#21=NFCT,I#22=GPIOTE,I#23=SAADC," \
| "I#24=TIMER0,I#25=TIMER1,I#26=TIMER2,I#27=RTC0,I#28=TEMP,I#29=RNG,I#30=ECB," \
| "I#31=CCM_AAR,I#32=WDT,I#33=RTC1,I#34=QDEC,I#35=COMP_LPCOMP,I#36=SWI0_EGU0," \
| "I#37=SWI1_EGU1,I#38=SWI2_EGU2,I#39=SWI3_EGU3,I#40=SWI4_EGU4,I#41=SWI5_EGU5," \
| "I#42=TIMER3,I#43=TIMER4,I#44=PWM0,I#45=PDM,I#48=MWU,I#49=PWM1,I#50=PWM2," \
| "I#51=SPIx2,I#52=RTC2,I#53=I2S,I#54=FPU,I#55=USBD," \
| "I#56=UARTE1,I#57=QSPI,I#58=CRYPTOCELL,I#61=PWM3,I#63=SPIM3"
|
| #endif
|
| #ifdef __cplusplus
| }
| #endif
|
| #endif /* __MCU_MCU_H_ */
|
|
