#MicroXplorer Configuration settings - do not modify
|
ADC1.Channel-0\#ChannelRegularConversion=ADC_CHANNEL_1
|
ADC1.Channel-1\#ChannelRegularConversion=ADC_CHANNEL_VREFINT
|
ADC1.ClockPrescaler=ADC_CLOCK_SYNC_PCLK_DIV4
|
ADC1.ContinuousConvMode=ENABLE
|
ADC1.DMAContinuousRequests=ENABLE
|
ADC1.DataAlign=ADC_DATAALIGN_RIGHT
|
ADC1.DiscontinuousConvMode=DISABLE
|
ADC1.EOCSelection=ADC_EOC_SINGLE_CONV
|
ADC1.EnableAnalogWatchDog=false
|
ADC1.ExternalTrigConv=ADC_SOFTWARE_START
|
ADC1.ExternalTrigConvEdge=ADC_EXTERNALTRIGCONVEDGE_NONE
|
ADC1.IPParameters=Rank-0\#ChannelRegularConversion,Channel-0\#ChannelRegularConversion,SamplingTime-0\#ChannelRegularConversion,NbrOfConversionFlag,master,ClockPrescaler,Resolution,DataAlign,ScanConvMode,ContinuousConvMode,DiscontinuousConvMode,DMAContinuousRequests,EOCSelection,NbrOfConversion,ExternalTrigConv,ExternalTrigConvEdge,InjNumberOfConversion,EnableAnalogWatchDog,Rank-1\#ChannelRegularConversion,Channel-1\#ChannelRegularConversion,SamplingTime-1\#ChannelRegularConversion
|
ADC1.InjNumberOfConversion=0
|
ADC1.NbrOfConversion=2
|
ADC1.NbrOfConversionFlag=1
|
ADC1.Rank-0\#ChannelRegularConversion=1
|
ADC1.Rank-1\#ChannelRegularConversion=2
|
ADC1.Resolution=ADC_RESOLUTION_12B
|
ADC1.SamplingTime-0\#ChannelRegularConversion=ADC_SAMPLETIME_480CYCLES
|
ADC1.SamplingTime-1\#ChannelRegularConversion=ADC_SAMPLETIME_480CYCLES
|
ADC1.ScanConvMode=ENABLE
|
ADC1.master=1
|
Dma.ADC1.6.Direction=DMA_PERIPH_TO_MEMORY
|
Dma.ADC1.6.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.ADC1.6.Instance=DMA2_Stream0
|
Dma.ADC1.6.MemDataAlignment=DMA_MDATAALIGN_HALFWORD
|
Dma.ADC1.6.MemInc=DMA_MINC_ENABLE
|
Dma.ADC1.6.Mode=DMA_CIRCULAR
|
Dma.ADC1.6.PeriphDataAlignment=DMA_PDATAALIGN_HALFWORD
|
Dma.ADC1.6.PeriphInc=DMA_PINC_DISABLE
|
Dma.ADC1.6.Priority=DMA_PRIORITY_VERY_HIGH
|
Dma.ADC1.6.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
Dma.Request0=USART1_RX
|
Dma.Request1=USART1_TX
|
Dma.Request2=USART2_RX
|
Dma.Request3=USART2_TX
|
Dma.Request4=USART6_RX
|
Dma.Request5=USART6_TX
|
Dma.Request6=ADC1
|
Dma.RequestsNb=7
|
Dma.USART1_RX.0.Direction=DMA_PERIPH_TO_MEMORY
|
Dma.USART1_RX.0.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.USART1_RX.0.Instance=DMA2_Stream2
|
Dma.USART1_RX.0.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
Dma.USART1_RX.0.MemInc=DMA_MINC_ENABLE
|
Dma.USART1_RX.0.Mode=DMA_CIRCULAR
|
Dma.USART1_RX.0.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
Dma.USART1_RX.0.PeriphInc=DMA_PINC_DISABLE
|
Dma.USART1_RX.0.Priority=DMA_PRIORITY_LOW
|
Dma.USART1_RX.0.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
Dma.USART1_TX.1.Direction=DMA_MEMORY_TO_PERIPH
|
Dma.USART1_TX.1.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.USART1_TX.1.Instance=DMA2_Stream7
|
Dma.USART1_TX.1.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
Dma.USART1_TX.1.MemInc=DMA_MINC_ENABLE
|
Dma.USART1_TX.1.Mode=DMA_NORMAL
|
Dma.USART1_TX.1.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
Dma.USART1_TX.1.PeriphInc=DMA_PINC_DISABLE
|
Dma.USART1_TX.1.Priority=DMA_PRIORITY_LOW
|
Dma.USART1_TX.1.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
Dma.USART2_RX.2.Direction=DMA_PERIPH_TO_MEMORY
|
Dma.USART2_RX.2.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.USART2_RX.2.Instance=DMA1_Stream5
|
Dma.USART2_RX.2.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
Dma.USART2_RX.2.MemInc=DMA_MINC_ENABLE
|
Dma.USART2_RX.2.Mode=DMA_CIRCULAR
|
Dma.USART2_RX.2.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
Dma.USART2_RX.2.PeriphInc=DMA_PINC_DISABLE
|
Dma.USART2_RX.2.Priority=DMA_PRIORITY_LOW
|
Dma.USART2_RX.2.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
Dma.USART2_TX.3.Direction=DMA_MEMORY_TO_PERIPH
|
Dma.USART2_TX.3.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.USART2_TX.3.Instance=DMA1_Stream6
|
Dma.USART2_TX.3.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
Dma.USART2_TX.3.MemInc=DMA_MINC_ENABLE
|
Dma.USART2_TX.3.Mode=DMA_NORMAL
|
Dma.USART2_TX.3.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
Dma.USART2_TX.3.PeriphInc=DMA_PINC_DISABLE
|
Dma.USART2_TX.3.Priority=DMA_PRIORITY_LOW
|
Dma.USART2_TX.3.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
Dma.USART6_RX.4.Direction=DMA_PERIPH_TO_MEMORY
|
Dma.USART6_RX.4.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.USART6_RX.4.Instance=DMA2_Stream1
|
Dma.USART6_RX.4.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
Dma.USART6_RX.4.MemInc=DMA_MINC_ENABLE
|
Dma.USART6_RX.4.Mode=DMA_CIRCULAR
|
Dma.USART6_RX.4.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
Dma.USART6_RX.4.PeriphInc=DMA_PINC_DISABLE
|
Dma.USART6_RX.4.Priority=DMA_PRIORITY_LOW
|
Dma.USART6_RX.4.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
Dma.USART6_TX.5.Direction=DMA_MEMORY_TO_PERIPH
|
Dma.USART6_TX.5.FIFOMode=DMA_FIFOMODE_DISABLE
|
Dma.USART6_TX.5.Instance=DMA2_Stream6
|
Dma.USART6_TX.5.MemDataAlignment=DMA_MDATAALIGN_BYTE
|
Dma.USART6_TX.5.MemInc=DMA_MINC_ENABLE
|
Dma.USART6_TX.5.Mode=DMA_NORMAL
|
Dma.USART6_TX.5.PeriphDataAlignment=DMA_PDATAALIGN_BYTE
|
Dma.USART6_TX.5.PeriphInc=DMA_PINC_DISABLE
|
Dma.USART6_TX.5.Priority=DMA_PRIORITY_LOW
|
Dma.USART6_TX.5.RequestParameters=Instance,Direction,PeriphInc,MemInc,PeriphDataAlignment,MemDataAlignment,Mode,Priority,FIFOMode
|
File.Version=6
|
KeepUserPlacement=false
|
Mcu.Family=STM32F4
|
Mcu.IP0=ADC1
|
Mcu.IP1=DMA
|
Mcu.IP10=USART6
|
Mcu.IP2=NVIC
|
Mcu.IP3=RCC
|
Mcu.IP4=SPI1
|
Mcu.IP5=SYS
|
Mcu.IP6=TIM1
|
Mcu.IP7=TIM3
|
Mcu.IP8=USART1
|
Mcu.IP9=USART2
|
Mcu.IPNb=11
|
Mcu.Name=STM32F401R(B-C)Tx
|
Mcu.Package=LQFP64
|
Mcu.Pin0=PC13-ANTI_TAMP
|
Mcu.Pin1=PC14-OSC32_IN
|
Mcu.Pin10=PA5
|
Mcu.Pin11=PA6
|
Mcu.Pin12=PA7
|
Mcu.Pin13=PC4
|
Mcu.Pin14=PB0
|
Mcu.Pin15=PB1
|
Mcu.Pin16=PB2
|
Mcu.Pin17=PB10
|
Mcu.Pin18=PB12
|
Mcu.Pin19=PB13
|
Mcu.Pin2=PC15-OSC32_OUT
|
Mcu.Pin20=PB14
|
Mcu.Pin21=PC6
|
Mcu.Pin22=PC7
|
Mcu.Pin23=PC8
|
Mcu.Pin24=PC9
|
Mcu.Pin25=PA8
|
Mcu.Pin26=PA9
|
Mcu.Pin27=PA10
|
Mcu.Pin28=PA11
|
Mcu.Pin29=PA12
|
Mcu.Pin3=PH0 - OSC_IN
|
Mcu.Pin30=PA13
|
Mcu.Pin31=PA14
|
Mcu.Pin32=PA15
|
Mcu.Pin33=PC12
|
Mcu.Pin34=PD2
|
Mcu.Pin35=PB3
|
Mcu.Pin36=PB4
|
Mcu.Pin37=PB5
|
Mcu.Pin38=PB6
|
Mcu.Pin39=PB7
|
Mcu.Pin4=PH1 - OSC_OUT
|
Mcu.Pin40=PB9
|
Mcu.Pin41=VP_ADC1_Vref_Input
|
Mcu.Pin42=VP_SYS_VS_Systick
|
Mcu.Pin43=VP_TIM3_VS_ClockSourceINT
|
Mcu.Pin5=PA0-WKUP
|
Mcu.Pin6=PA1
|
Mcu.Pin7=PA2
|
Mcu.Pin8=PA3
|
Mcu.Pin9=PA4
|
Mcu.PinsNb=44
|
Mcu.ThirdPartyNb=0
|
Mcu.UserConstants=
|
Mcu.UserName=STM32F401RCTx
|
MxCube.Version=4.25.0
|
MxDb.Version=DB.4.0.250
|
NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA1_Stream5_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA1_Stream6_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA2_Stream0_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA2_Stream1_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA2_Stream2_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA2_Stream6_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DMA2_Stream7_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.EXTI0_IRQn=true\:1\:0\:true\:false\:true\:true
|
NVIC.EXTI15_10_IRQn=true\:0\:0\:false\:false\:true\:true
|
NVIC.EXTI1_IRQn=true\:1\:0\:true\:false\:true\:true
|
NVIC.EXTI9_5_IRQn=true\:1\:0\:true\:false\:true\:true
|
NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
|
NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:false
|
NVIC.TIM3_IRQn=true\:0\:0\:true\:false\:true\:true
|
NVIC.USART1_IRQn=true\:1\:0\:true\:false\:true\:true
|
NVIC.USART2_IRQn=true\:1\:0\:true\:false\:true\:true
|
NVIC.USART6_IRQn=true\:1\:0\:true\:false\:true\:true
|
NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false
|
PA0-WKUP.Locked=true
|
PA0-WKUP.Signal=GPXTI0
|
PA1.Locked=true
|
PA1.Signal=ADCx_IN1
|
PA10.Locked=true
|
PA10.Mode=Asynchronous
|
PA10.Signal=USART1_RX
|
PA11.Locked=true
|
PA11.Signal=S_TIM1_CH4
|
PA12.Locked=true
|
PA12.Signal=GPIO_Output
|
PA13.Mode=Serial_Wire
|
PA13.Signal=SYS_JTMS-SWDIO
|
PA14.Mode=Serial_Wire
|
PA14.Signal=SYS_JTCK-SWCLK
|
PA15.GPIOParameters=PinState
|
PA15.Locked=true
|
PA15.PinState=GPIO_PIN_SET
|
PA15.Signal=GPIO_Output
|
PA2.Mode=Asynchronous
|
PA2.Signal=USART2_TX
|
PA3.Mode=Asynchronous
|
PA3.Signal=USART2_RX
|
PA4.GPIOParameters=PinState
|
PA4.Locked=true
|
PA4.PinState=GPIO_PIN_SET
|
PA4.Signal=GPIO_Output
|
PA5.Mode=Full_Duplex_Master
|
PA5.Signal=SPI1_SCK
|
PA6.Mode=Full_Duplex_Master
|
PA6.Signal=SPI1_MISO
|
PA7.Mode=Full_Duplex_Master
|
PA7.Signal=SPI1_MOSI
|
PA8.GPIOParameters=PinState
|
PA8.Locked=true
|
PA8.PinState=GPIO_PIN_SET
|
PA8.Signal=GPIO_Output
|
PA9.Mode=Asynchronous
|
PA9.Signal=USART1_TX
|
PB0.Locked=true
|
PB0.Signal=GPIO_Output
|
PB1.GPIOParameters=GPIO_PuPd,GPIO_ModeDefaultEXTI
|
PB1.GPIO_ModeDefaultEXTI=GPIO_MODE_IT_RISING
|
PB1.GPIO_PuPd=GPIO_PULLUP
|
PB1.Locked=true
|
PB1.Signal=GPXTI1
|
PB10.GPIOParameters=PinState
|
PB10.Locked=true
|
PB10.PinState=GPIO_PIN_SET
|
PB10.Signal=GPIO_Output
|
PB12.Locked=true
|
PB12.Signal=GPXTI12
|
PB13.GPIOParameters=GPIO_Speed,PinState,GPIO_ModeDefaultOutputPP
|
PB13.GPIO_ModeDefaultOutputPP=GPIO_MODE_OUTPUT_OD
|
PB13.GPIO_Speed=GPIO_SPEED_FREQ_VERY_HIGH
|
PB13.Locked=true
|
PB13.PinState=GPIO_PIN_SET
|
PB13.Signal=GPIO_Output
|
PB14.GPIOParameters=GPIO_Speed,PinState,GPIO_ModeDefaultOutputPP
|
PB14.GPIO_ModeDefaultOutputPP=GPIO_MODE_OUTPUT_OD
|
PB14.GPIO_Speed=GPIO_SPEED_FREQ_VERY_HIGH
|
PB14.Locked=true
|
PB14.PinState=GPIO_PIN_SET
|
PB14.Signal=GPIO_Output
|
PB2.Locked=true
|
PB2.Signal=GPIO_Output
|
PB3.GPIOParameters=PinState
|
PB3.Locked=true
|
PB3.PinState=GPIO_PIN_SET
|
PB3.Signal=GPIO_Output
|
PB4.Locked=true
|
PB4.Signal=GPIO_Input
|
PB5.Locked=true
|
PB5.Signal=GPIO_Output
|
PB6.GPIOParameters=PinState
|
PB6.Locked=true
|
PB6.PinState=GPIO_PIN_SET
|
PB6.Signal=GPIO_Output
|
PB7.Locked=true
|
PB7.Signal=GPIO_Output
|
PB9.Locked=true
|
PB9.Signal=GPIO_Input
|
PC12.GPIOParameters=PinState
|
PC12.Locked=true
|
PC12.PinState=GPIO_PIN_SET
|
PC12.Signal=GPIO_Output
|
PC13-ANTI_TAMP.Locked=true
|
PC13-ANTI_TAMP.Signal=GPIO_Input
|
PC14-OSC32_IN.Mode=LSE-External-Oscillator
|
PC14-OSC32_IN.Signal=RCC_OSC32_IN
|
PC15-OSC32_OUT.Mode=LSE-External-Oscillator
|
PC15-OSC32_OUT.Signal=RCC_OSC32_OUT
|
PC4.GPIOParameters=PinState
|
PC4.Locked=true
|
PC4.PinState=GPIO_PIN_SET
|
PC4.Signal=GPIO_Output
|
PC6.Locked=true
|
PC6.Mode=Asynchronous
|
PC6.Signal=USART6_TX
|
PC7.Locked=true
|
PC7.Mode=Asynchronous
|
PC7.Signal=USART6_RX
|
PC8.Locked=true
|
PC8.Signal=GPIO_Output
|
PC9.Locked=true
|
PC9.Signal=GPXTI9
|
PCC.Checker=false
|
PCC.Line=STM32F401
|
PCC.MCU=STM32F401R(B-C)Tx
|
PCC.PartNumber=STM32F401RCTx
|
PCC.Seq0=0
|
PCC.Series=STM32F4
|
PCC.Temperature=25
|
PCC.Vdd=null
|
PD2.GPIOParameters=GPIO_Speed,PinState
|
PD2.GPIO_Speed=GPIO_SPEED_FREQ_HIGH
|
PD2.Locked=true
|
PD2.PinState=GPIO_PIN_RESET
|
PD2.Signal=GPIO_Output
|
PH0\ -\ OSC_IN.Mode=HSE-External-Oscillator
|
PH0\ -\ OSC_IN.Signal=RCC_OSC_IN
|
PH1\ -\ OSC_OUT.Mode=HSE-External-Oscillator
|
PH1\ -\ OSC_OUT.Signal=RCC_OSC_OUT
|
PinOutPanel.RotationAngle=0
|
ProjectManager.AskForMigrate=true
|
ProjectManager.BackupPrevious=false
|
ProjectManager.CompilerOptimize=3
|
ProjectManager.ComputerToolchain=false
|
ProjectManager.CoupleFile=false
|
ProjectManager.CustomerFirmwarePackage=
|
ProjectManager.DefaultFWLocation=true
|
ProjectManager.DeletePrevious=true
|
ProjectManager.DeviceId=STM32F401RCTx
|
ProjectManager.FirmwarePackage=STM32Cube FW_F4 V1.21.0
|
ProjectManager.FreePins=false
|
ProjectManager.HalAssertFull=false
|
ProjectManager.HeapSize=0x200
|
ProjectManager.KeepUserCode=true
|
ProjectManager.LastFirmware=true
|
ProjectManager.LibraryCopy=0
|
ProjectManager.MainLocation=Src
|
ProjectManager.PreviousToolchain=
|
ProjectManager.ProjectBuild=false
|
ProjectManager.ProjectFileName=UWB_RTK_STM32F4.ioc
|
ProjectManager.ProjectName=UWB_RTK_STM32F4
|
ProjectManager.StackSize=0x800
|
ProjectManager.TargetToolchain=MDK-ARM V5
|
ProjectManager.ToolChainLocation=
|
ProjectManager.UnderRoot=false
|
ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-MX_DMA_Init-DMA-false-HAL-true,3-SystemClock_Config-RCC-false-HAL-false,4-MX_ADC1_Init-ADC1-false-HAL-true,5-MX_SPI1_Init-SPI1-false-HAL-true,6-MX_USART2_UART_Init-USART2-false-HAL-true,7-MX_USART1_UART_Init-USART1-false-HAL-true,8-MX_USART6_UART_Init-USART6-false-HAL-true,9-MX_TIM3_Init-TIM3-false-HAL-true,10-MX_TIM1_Init-TIM1-false-HAL-true
|
RCC.48MHZClocksFreq_Value=40000000
|
RCC.AHBFreq_Value=80000000
|
RCC.APB1CLKDivider=RCC_HCLK_DIV2
|
RCC.APB1Freq_Value=40000000
|
RCC.APB1TimFreq_Value=80000000
|
RCC.APB2Freq_Value=80000000
|
RCC.APB2TimFreq_Value=80000000
|
RCC.CortexFreq_Value=80000000
|
RCC.FCLKCortexFreq_Value=80000000
|
RCC.HCLKFreq_Value=80000000
|
RCC.HSE_VALUE=8000000
|
RCC.HSI_VALUE=16000000
|
RCC.I2SClocksFreq_Value=96000000
|
RCC.IPParameters=48MHZClocksFreq_Value,AHBFreq_Value,APB1CLKDivider,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,CortexFreq_Value,FCLKCortexFreq_Value,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2SClocksFreq_Value,LSI_VALUE,MCO2PinFreq_Value,PLLCLKFreq_Value,PLLM,PLLN,PLLQCLKFreq_Value,PLLSourceVirtual,RCC_RTC_Clock_SourceVirtual,RTCFreq_Value,RTCHSEDivFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,VCOI2SOutputFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VcooutputI2S
|
RCC.LSI_VALUE=32000
|
RCC.MCO2PinFreq_Value=80000000
|
RCC.PLLCLKFreq_Value=80000000
|
RCC.PLLM=8
|
RCC.PLLN=160
|
RCC.PLLQCLKFreq_Value=40000000
|
RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSE
|
RCC.RCC_RTC_Clock_SourceVirtual=RCC_RTCCLKSOURCE_LSE
|
RCC.RTCFreq_Value=32768
|
RCC.RTCHSEDivFreq_Value=4000000
|
RCC.SYSCLKFreq_VALUE=80000000
|
RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK
|
RCC.VCOI2SOutputFreq_Value=192000000
|
RCC.VCOInputFreq_Value=1000000
|
RCC.VCOOutputFreq_Value=160000000
|
RCC.VcooutputI2S=96000000
|
SH.ADCx_IN1.0=ADC1_IN1,IN1
|
SH.ADCx_IN1.ConfNb=1
|
SH.GPXTI0.0=GPIO_EXTI0
|
SH.GPXTI0.ConfNb=1
|
SH.GPXTI1.0=GPIO_EXTI1
|
SH.GPXTI1.ConfNb=1
|
SH.GPXTI12.0=GPIO_EXTI12
|
SH.GPXTI12.ConfNb=1
|
SH.GPXTI9.0=GPIO_EXTI9
|
SH.GPXTI9.ConfNb=1
|
SH.S_TIM1_CH4.0=TIM1_CH4,PWM Generation4 CH4
|
SH.S_TIM1_CH4.ConfNb=1
|
SPI1.BaudRatePrescaler=SPI_BAUDRATEPRESCALER_4
|
SPI1.CalculateBaudRate=20.0 MBits/s
|
SPI1.Direction=SPI_DIRECTION_2LINES
|
SPI1.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate,BaudRatePrescaler
|
SPI1.Mode=SPI_MODE_MASTER
|
SPI1.VirtualType=VM_MASTER
|
TIM1.Channel-PWM\ Generation4\ CH4=TIM_CHANNEL_4
|
TIM1.IPParameters=Channel-PWM Generation4 CH4,Prescaler,Period,Pulse-PWM Generation4 CH4
|
TIM1.Period=2928
|
TIM1.Prescaler=9
|
TIM1.Pulse-PWM\ Generation4\ CH4=1464
|
TIM3.IPParameters=Prescaler,Period,TIM_MasterOutputTrigger
|
TIM3.Period=1000
|
TIM3.Prescaler=80-1
|
TIM3.TIM_MasterOutputTrigger=TIM_TRGO_RESET
|
USART1.BaudRate=921600
|
USART1.IPParameters=VirtualMode,BaudRate
|
USART1.VirtualMode=VM_ASYNC
|
USART2.BaudRate=38400
|
USART2.IPParameters=VirtualMode,BaudRate
|
USART2.VirtualMode=VM_ASYNC
|
USART6.IPParameters=VirtualMode
|
USART6.VirtualMode=VM_ASYNC
|
VP_ADC1_Vref_Input.Mode=IN-Vrefint
|
VP_ADC1_Vref_Input.Signal=ADC1_Vref_Input
|
VP_SYS_VS_Systick.Mode=SysTick
|
VP_SYS_VS_Systick.Signal=SYS_VS_Systick
|
VP_TIM3_VS_ClockSourceINT.Mode=Internal
|
VP_TIM3_VS_ClockSourceINT.Signal=TIM3_VS_ClockSourceINT
|
board=UWB_RTK_STM32F4
|
