/*
|
* Copyright (c) 2019-2023 Beijing Hanwei Innovation Technology Ltd. Co. and
|
* its subsidiaries and affiliates (collectly called MKSEMI).
|
*
|
* All rights reserved.
|
*
|
* Redistribution and use in source and binary forms, with or without
|
* modification, are permitted provided that the following conditions are met:
|
*
|
* 1. Redistributions of source code must retain the above copyright notice,
|
* this list of conditions and the following disclaimer.
|
*
|
* 2. Redistributions in binary form, except as embedded into an MKSEMI
|
* integrated circuit in a product or a software update for such product,
|
* must reproduce the above copyright notice, this list of conditions and
|
* the following disclaimer in the documentation and/or other materials
|
* provided with the distribution.
|
*
|
* 3. Neither the name of MKSEMI nor the names of its contributors may be used
|
* to endorse or promote products derived from this software without
|
* specific prior written permission.
|
*
|
* 4. This software, with or without modification, must only be used with a
|
* MKSEMI integrated circuit.
|
*
|
* 5. Any software provided in binary form under this license must not be
|
* reverse engineered, decompiled, modified and/or disassembled.
|
*
|
* THIS SOFTWARE IS PROVIDED BY MKSEMI "AS IS" AND ANY EXPRESS OR IMPLIED
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
* MERCHANTABILITY, NONINFRINGEMENT, AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
* DISCLAIMED. IN NO EVENT SHALL MKSEMI OR CONTRIBUTORS BE LIABLE FOR ANY
|
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
|
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
|
* THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
*/
|
|
#include "mk_gpio.h"
|
#include "mk_trace.h"
|
#include "mk_reset.h"
|
#include "mk_calib.h"
|
#include "mk_wdt.h"
|
#include "mk_misc.h"
|
#include "libc_rom.h"
|
#include "board.h"
|
|
static void gpio_ext_int_callback(enum IO_PIN_T pin)
|
{
|
if (BOARD_SW_1 == pin)
|
{
|
LOG_INFO(TRACE_MODULE_APP, "Board leds toggled\r\n");
|
gpio_pin_toggle(BOARD_LED_1);
|
gpio_pin_toggle(BOARD_LED_2);
|
}
|
}
|
|
int main(void)
|
{
|
board_clock_run();
|
board_pins_config();
|
board_debug_console_open(TRACE_PORT_UART0);
|
// Reset reason
|
reset_cause_get();
|
reset_cause_clear();
|
|
// Chip calibration
|
calib_chip();
|
|
// Disable watchdog timer
|
wdt_close(WDT_ID0);
|
LOG_INFO(TRACE_MODULE_APP, "GPIO example\r\n");
|
|
gpio_open();
|
board_configure();
|
gpio_pin_set_dir(IO_PIN_0, GPIO_DIR_OUT, 0);
|
gpio_pin_set_dir(IO_PIN_1, GPIO_DIR_OUT, 1);
|
gpio_pin_set_dir(IO_PIN_2, GPIO_DIR_OUT, 0);
|
gpio_pin_set_dir(IO_PIN_3, GPIO_DIR_OUT, 1);
|
gpio_pin_set_dir(IO_PIN_4, GPIO_DIR_OUT, 0);
|
gpio_pin_set_dir(IO_PIN_7, GPIO_DIR_OUT, 1);
|
gpio_pin_set_dir(IO_PIN_8, GPIO_DIR_OUT, 0);
|
gpio_pin_set_dir(IO_PIN_9, GPIO_DIR_OUT, 1);
|
gpio_pin_set_dir(IO_PIN_10, GPIO_DIR_OUT, 0);
|
gpio_pin_set_dir(IO_PIN_11, GPIO_DIR_OUT, 1);
|
gpio_pin_set_dir(IO_PIN_12, GPIO_DIR_OUT, 0);
|
gpio_pin_set_dir(IO_PIN_13, GPIO_DIR_OUT, 1);
|
|
board_led_init();
|
// Pressing the button triggers interrupt
|
gpio_pin_set_dir(BOARD_SW_1, GPIO_DIR_IN, 0);
|
io_pull_set(BOARD_SW_1, IO_PULL_UP, IO_PULL_UP_LEVEL0);
|
gpio_enable_irq(BOARD_SW_1, GPIO_IRQ_TYPE_FALLING_EDGE, gpio_ext_int_callback);
|
|
sys_timer_open();
|
uint16_t log_cnt = 0;
|
|
while (1)
|
{
|
gpio_pin_toggle(IO_PIN_0);
|
gpio_pin_toggle(IO_PIN_1);
|
gpio_pin_toggle(IO_PIN_2);
|
gpio_pin_toggle(IO_PIN_3);
|
gpio_pin_toggle(IO_PIN_4);
|
gpio_pin_toggle(IO_PIN_7);
|
gpio_pin_toggle(IO_PIN_8);
|
gpio_pin_toggle(IO_PIN_9);
|
gpio_pin_toggle(IO_PIN_10);
|
gpio_pin_toggle(IO_PIN_11);
|
gpio_pin_toggle(IO_PIN_12);
|
gpio_pin_toggle(IO_PIN_13);
|
|
sys_timer_delay_ms(10);
|
|
log_cnt++;
|
if (log_cnt % 100 == 0)
|
{
|
LOG_INFO(TRACE_MODULE_APP, "GPIO toggled\r\n");
|
}
|
}
|
}
|
