/**
|
******************************************************************************
|
* @file stm32100b_eval.c
|
* @author MCD Application Team
|
* @version V4.5.0
|
* @date 07-March-2011
|
* @brief This file provides
|
* - set of firmware functions to manage Leds, push-button and COM ports
|
* - low level initialization functions for SD card (on SPI), SPI serial
|
* flash (sFLASH) and temperature sensor (LM75)
|
* available on STM32100B-EVAL evaluation board from STMicroelectronics.
|
******************************************************************************
|
* @attention
|
*
|
* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
|
* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
|
* TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
|
* DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
|
* FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
|
* CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
|
*
|
* <h2><center>© COPYRIGHT 2011 STMicroelectronics</center></h2>
|
******************************************************************************
|
*/
|
|
/* Includes ------------------------------------------------------------------*/
|
#include "stm32100b_eval.h"
|
#include "stm32f10x_spi.h"
|
#include "stm32f10x_i2c.h"
|
|
/** @addtogroup Utilities
|
* @{
|
*/
|
|
/** @addtogroup STM32_EVAL
|
* @{
|
*/
|
|
/** @addtogroup STM32100B_EVAL
|
* @{
|
*/
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL
|
* @brief This file provides firmware functions to manage Leds, push-buttons,
|
* COM ports, SD card on SPI, serial flash (sFLASH) and temperature
|
* sensor (LM75) available on STM32100B-EVAL evaluation board from
|
* STMicroelectronics.
|
* @{
|
*/
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL_Private_TypesDefinitions
|
* @{
|
*/
|
/**
|
* @}
|
*/
|
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL_Private_Defines
|
* @{
|
*/
|
/**
|
* @}
|
*/
|
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL_Private_Macros
|
* @{
|
*/
|
/**
|
* @}
|
*/
|
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL_Private_Variables
|
* @{
|
*/
|
GPIO_TypeDef* GPIO_PORT[LEDn] = {LED1_GPIO_PORT, LED2_GPIO_PORT, LED3_GPIO_PORT,
|
LED4_GPIO_PORT};
|
const uint16_t GPIO_PIN[LEDn] = {LED1_PIN, LED2_PIN, LED3_PIN,
|
LED4_PIN};
|
const uint32_t GPIO_CLK[LEDn] = {LED1_GPIO_CLK, LED2_GPIO_CLK, LED3_GPIO_CLK,
|
LED4_GPIO_CLK};
|
|
GPIO_TypeDef* BUTTON_PORT[BUTTONn] = {WAKEUP_BUTTON_GPIO_PORT, TAMPER_BUTTON_GPIO_PORT,
|
KEY_BUTTON_GPIO_PORT, RIGHT_BUTTON_GPIO_PORT,
|
LEFT_BUTTON_GPIO_PORT, UP_BUTTON_GPIO_PORT,
|
DOWN_BUTTON_GPIO_PORT, SEL_BUTTON_GPIO_PORT};
|
|
const uint16_t BUTTON_PIN[BUTTONn] = {WAKEUP_BUTTON_PIN, TAMPER_BUTTON_PIN,
|
KEY_BUTTON_PIN, RIGHT_BUTTON_PIN,
|
LEFT_BUTTON_PIN, UP_BUTTON_PIN,
|
DOWN_BUTTON_PIN, SEL_BUTTON_PIN};
|
|
const uint32_t BUTTON_CLK[BUTTONn] = {WAKEUP_BUTTON_GPIO_CLK, TAMPER_BUTTON_GPIO_CLK,
|
KEY_BUTTON_GPIO_CLK, RIGHT_BUTTON_GPIO_CLK,
|
LEFT_BUTTON_GPIO_CLK, UP_BUTTON_GPIO_CLK,
|
DOWN_BUTTON_GPIO_CLK, SEL_BUTTON_GPIO_CLK};
|
|
const uint16_t BUTTON_EXTI_LINE[BUTTONn] = {WAKEUP_BUTTON_EXTI_LINE,
|
TAMPER_BUTTON_EXTI_LINE,
|
KEY_BUTTON_EXTI_LINE,
|
RIGHT_BUTTON_EXTI_LINE,
|
LEFT_BUTTON_EXTI_LINE,
|
UP_BUTTON_EXTI_LINE,
|
DOWN_BUTTON_EXTI_LINE,
|
SEL_BUTTON_EXTI_LINE};
|
|
const uint16_t BUTTON_PORT_SOURCE[BUTTONn] = {WAKEUP_BUTTON_EXTI_PORT_SOURCE,
|
TAMPER_BUTTON_EXTI_PORT_SOURCE,
|
KEY_BUTTON_EXTI_PORT_SOURCE,
|
RIGHT_BUTTON_EXTI_PORT_SOURCE,
|
LEFT_BUTTON_EXTI_PORT_SOURCE,
|
UP_BUTTON_EXTI_PORT_SOURCE,
|
DOWN_BUTTON_EXTI_PORT_SOURCE,
|
SEL_BUTTON_EXTI_PORT_SOURCE};
|
|
const uint16_t BUTTON_PIN_SOURCE[BUTTONn] = {WAKEUP_BUTTON_EXTI_PIN_SOURCE,
|
TAMPER_BUTTON_EXTI_PIN_SOURCE,
|
KEY_BUTTON_EXTI_PIN_SOURCE,
|
RIGHT_BUTTON_EXTI_PIN_SOURCE,
|
LEFT_BUTTON_EXTI_PIN_SOURCE,
|
UP_BUTTON_EXTI_PIN_SOURCE,
|
DOWN_BUTTON_EXTI_PIN_SOURCE,
|
SEL_BUTTON_EXTI_PIN_SOURCE};
|
|
const uint16_t BUTTON_IRQn[BUTTONn] = {WAKEUP_BUTTON_EXTI_IRQn, TAMPER_BUTTON_EXTI_IRQn,
|
KEY_BUTTON_EXTI_IRQn, RIGHT_BUTTON_EXTI_IRQn,
|
LEFT_BUTTON_EXTI_IRQn, UP_BUTTON_EXTI_IRQn,
|
DOWN_BUTTON_EXTI_IRQn, SEL_BUTTON_EXTI_IRQn};
|
|
USART_TypeDef* COM_USART[COMn] = {EVAL_COM1, EVAL_COM2};
|
|
GPIO_TypeDef* COM_TX_PORT[COMn] = {EVAL_COM1_TX_GPIO_PORT, EVAL_COM2_TX_GPIO_PORT};
|
|
GPIO_TypeDef* COM_RX_PORT[COMn] = {EVAL_COM1_RX_GPIO_PORT, EVAL_COM2_RX_GPIO_PORT};
|
|
const uint32_t COM_USART_CLK[COMn] = {EVAL_COM1_CLK, EVAL_COM2_CLK};
|
|
const uint32_t COM_TX_PORT_CLK[COMn] = {EVAL_COM1_TX_GPIO_CLK, EVAL_COM2_TX_GPIO_CLK};
|
|
const uint32_t COM_RX_PORT_CLK[COMn] = {EVAL_COM1_RX_GPIO_CLK, EVAL_COM2_RX_GPIO_CLK};
|
|
const uint16_t COM_TX_PIN[COMn] = {EVAL_COM1_TX_PIN, EVAL_COM2_TX_PIN};
|
|
const uint16_t COM_RX_PIN[COMn] = {EVAL_COM1_RX_PIN, EVAL_COM2_RX_PIN};
|
|
/**
|
* @}
|
*/
|
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL_Private_FunctionPrototypes
|
* @{
|
*/
|
|
/**
|
* @}
|
*/
|
|
|
/** @defgroup STM32100B_EVAL_LOW_LEVEL_Private_Functions
|
* @{
|
*/
|
|
/**
|
* @brief Configures LED GPIO.
|
* @param Led: Specifies the Led to be configured.
|
* This parameter can be one of following parameters:
|
* @arg LED1
|
* @arg LED2
|
* @arg LED3
|
* @arg LED4
|
* @retval None
|
*/
|
void STM_EVAL_LEDInit(Led_TypeDef Led)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
/* Enable the GPIO_LED Clock */
|
RCC_APB2PeriphClockCmd(GPIO_CLK[Led], ENABLE);
|
|
/* Configure the GPIO_LED pin */
|
GPIO_InitStructure.GPIO_Pin = GPIO_PIN[Led];
|
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
|
GPIO_Init(GPIO_PORT[Led], &GPIO_InitStructure);
|
}
|
|
/**
|
* @brief Turns selected LED On.
|
* @param Led: Specifies the Led to be set on.
|
* This parameter can be one of following parameters:
|
* @arg LED1
|
* @arg LED2
|
* @arg LED3
|
* @arg LED4
|
* @retval None
|
*/
|
void STM_EVAL_LEDOn(Led_TypeDef Led)
|
{
|
GPIO_PORT[Led]->BSRR = GPIO_PIN[Led];
|
}
|
|
/**
|
* @brief Turns selected LED Off.
|
* @param Led: Specifies the Led to be set off.
|
* This parameter can be one of following parameters:
|
* @arg LED1
|
* @arg LED2
|
* @arg LED3
|
* @arg LED4
|
* @retval None
|
*/
|
void STM_EVAL_LEDOff(Led_TypeDef Led)
|
{
|
GPIO_PORT[Led]->BRR = GPIO_PIN[Led];
|
}
|
|
/**
|
* @brief Toggles the selected LED.
|
* @param Led: Specifies the Led to be toggled.
|
* This parameter can be one of following parameters:
|
* @arg LED1
|
* @arg LED2
|
* @arg LED3
|
* @arg LED4
|
* @retval None
|
*/
|
void STM_EVAL_LEDToggle(Led_TypeDef Led)
|
{
|
GPIO_PORT[Led]->ODR ^= GPIO_PIN[Led];
|
}
|
|
/**
|
* @brief Configures Button GPIO and EXTI Line.
|
* @param Button: Specifies the Button to be configured.
|
* This parameter can be one of following parameters:
|
* @arg BUTTON_WAKEUP: Wakeup Push Button
|
* @arg BUTTON_TAMPER: Tamper Push Button
|
* @arg BUTTON_KEY: Key Push Button
|
* @arg BUTTON_RIGHT: Joystick Right Push Button
|
* @arg BUTTON_LEFT: Joystick Left Push Button
|
* @arg BUTTON_UP: Joystick Up Push Button
|
* @arg BUTTON_DOWN: Joystick Down Push Button
|
* @arg BUTTON_SEL: Joystick Sel Push Button
|
* @param Button_Mode: Specifies Button mode.
|
* This parameter can be one of following parameters:
|
* @arg BUTTON_MODE_GPIO: Button will be used as simple IO
|
* @arg BUTTON_MODE_EXTI: Button will be connected to EXTI line with interrupt
|
* generation capability
|
* @retval None
|
*/
|
void STM_EVAL_PBInit(Button_TypeDef Button, ButtonMode_TypeDef Button_Mode)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
EXTI_InitTypeDef EXTI_InitStructure;
|
NVIC_InitTypeDef NVIC_InitStructure;
|
|
/* Enable the BUTTON Clock */
|
RCC_APB2PeriphClockCmd(BUTTON_CLK[Button] | RCC_APB2Periph_AFIO, ENABLE);
|
|
/* Configure Button pin as input floating */
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_InitStructure.GPIO_Pin = BUTTON_PIN[Button];
|
GPIO_Init(BUTTON_PORT[Button], &GPIO_InitStructure);
|
|
|
if (Button_Mode == BUTTON_MODE_EXTI)
|
{
|
/* Connect Button EXTI Line to Button GPIO Pin */
|
GPIO_EXTILineConfig(BUTTON_PORT_SOURCE[Button], BUTTON_PIN_SOURCE[Button]);
|
|
/* Configure Button EXTI line */
|
EXTI_InitStructure.EXTI_Line = BUTTON_EXTI_LINE[Button];
|
EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;
|
|
if(Button != BUTTON_WAKEUP)
|
{
|
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
|
}
|
else
|
{
|
EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
|
}
|
EXTI_InitStructure.EXTI_LineCmd = ENABLE;
|
EXTI_Init(&EXTI_InitStructure);
|
|
/* Enable and set Button EXTI Interrupt to the lowest priority */
|
NVIC_InitStructure.NVIC_IRQChannel = BUTTON_IRQn[Button];
|
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x0F;
|
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x0F;
|
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
|
|
NVIC_Init(&NVIC_InitStructure);
|
}
|
}
|
|
/**
|
* @brief Returns the selected Button state.
|
* @param Button: Specifies the Button to be checked.
|
* This parameter can be one of following parameters:
|
* @arg BUTTON_WAKEUP: Wakeup Push Button
|
* @arg BUTTON_TAMPER: Tamper Push Button
|
* @arg BUTTON_KEY: Key Push Button
|
* @arg BUTTON_RIGHT: Joystick Right Push Button
|
* @arg BUTTON_LEFT: Joystick Left Push Button
|
* @arg BUTTON_UP: Joystick Up Push Button
|
* @arg BUTTON_DOWN: Joystick Down Push Button
|
* @arg BUTTON_SEL: Joystick Sel Push Button
|
* @retval The Button GPIO pin value.
|
*/
|
uint32_t STM_EVAL_PBGetState(Button_TypeDef Button)
|
{
|
return GPIO_ReadInputDataBit(BUTTON_PORT[Button], BUTTON_PIN[Button]);
|
}
|
|
|
/**
|
* @brief Configures COM port.
|
* @param COM: Specifies the COM port to be configured.
|
* This parameter can be one of following parameters:
|
* @arg COM1
|
* @arg COM2
|
* @param USART_InitStruct: pointer to a USART_InitTypeDef structure that
|
* contains the configuration information for the specified USART peripheral.
|
* @retval None
|
*/
|
void STM_EVAL_COMInit(COM_TypeDef COM, USART_InitTypeDef* USART_InitStruct)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
/* Enable GPIO clock */
|
RCC_APB2PeriphClockCmd(COM_TX_PORT_CLK[COM] | COM_RX_PORT_CLK[COM] | RCC_APB2Periph_AFIO, ENABLE);
|
|
|
/* Enable UART clock */
|
if (COM == COM1)
|
{
|
RCC_APB2PeriphClockCmd(COM_USART_CLK[COM], ENABLE);
|
}
|
else
|
{
|
/* Enable the USART2 Pins Software Remapping */
|
GPIO_PinRemapConfig(GPIO_Remap_USART2, ENABLE);
|
RCC_APB1PeriphClockCmd(COM_USART_CLK[COM], ENABLE);
|
}
|
|
/* Configure USART Tx as alternate function push-pull */
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
|
GPIO_InitStructure.GPIO_Pin = COM_TX_PIN[COM];
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
|
GPIO_Init(COM_TX_PORT[COM], &GPIO_InitStructure);
|
|
/* Configure USART Rx as input floating */
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_InitStructure.GPIO_Pin = COM_RX_PIN[COM];
|
GPIO_Init(COM_RX_PORT[COM], &GPIO_InitStructure);
|
|
/* USART configuration */
|
USART_Init(COM_USART[COM], USART_InitStruct);
|
|
/* Enable USART */
|
USART_Cmd(COM_USART[COM], ENABLE);
|
}
|
|
/**
|
* @brief DeInitializes the SD/SD communication.
|
* @param None
|
* @retval None
|
*/
|
void SD_LowLevel_DeInit(void)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
SPI_Cmd(SD_SPI, DISABLE); /*!< SD_SPI disable */
|
SPI_I2S_DeInit(SD_SPI); /*!< DeInitializes the SD_SPI */
|
|
/*!< SD_SPI Periph clock disable */
|
RCC_APB2PeriphClockCmd(SD_SPI_CLK, DISABLE);
|
|
/*!< Configure SD_SPI pins: SCK */
|
GPIO_InitStructure.GPIO_Pin = SD_SPI_SCK_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_Init(SD_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI pins: MISO */
|
GPIO_InitStructure.GPIO_Pin = SD_SPI_MISO_PIN;
|
GPIO_Init(SD_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI pins: MOSI */
|
GPIO_InitStructure.GPIO_Pin = SD_SPI_MOSI_PIN;
|
GPIO_Init(SD_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI_CS_PIN pin: SD Card CS pin */
|
GPIO_InitStructure.GPIO_Pin = SD_CS_PIN;
|
GPIO_Init(SD_CS_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI_DETECT_PIN pin: SD Card detect pin */
|
GPIO_InitStructure.GPIO_Pin = SD_DETECT_PIN;
|
GPIO_Init(SD_DETECT_GPIO_PORT, &GPIO_InitStructure);
|
}
|
|
/**
|
* @brief Initializes the SD_SPI and CS pins.
|
* @param None
|
* @retval None
|
*/
|
void SD_LowLevel_Init(void)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
SPI_InitTypeDef SPI_InitStructure;
|
|
/*!< SD_SPI_CS_GPIO, SD_SPI_MOSI_GPIO, SD_SPI_MISO_GPIO, SD_SPI_DETECT_GPIO
|
and SD_SPI_SCK_GPIO Periph clock enable */
|
RCC_APB2PeriphClockCmd(SD_CS_GPIO_CLK | SD_SPI_MOSI_GPIO_CLK | SD_SPI_MISO_GPIO_CLK |
|
SD_SPI_SCK_GPIO_CLK | SD_DETECT_GPIO_CLK, ENABLE);
|
|
/*!< SD_SPI Periph clock enable */
|
RCC_APB2PeriphClockCmd(SD_SPI_CLK, ENABLE);
|
|
|
/*!< Configure SD_SPI pins: SCK */
|
GPIO_InitStructure.GPIO_Pin = SD_SPI_SCK_PIN;
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
|
GPIO_Init(SD_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI pins: MOSI */
|
GPIO_InitStructure.GPIO_Pin = SD_SPI_MOSI_PIN;
|
GPIO_Init(SD_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI pins: MISO */
|
GPIO_InitStructure.GPIO_Pin = SD_SPI_MISO_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_Init(SD_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI_CS_PIN pin: SD Card CS pin */
|
GPIO_InitStructure.GPIO_Pin = SD_CS_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
|
GPIO_Init(SD_CS_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure SD_SPI_DETECT_PIN pin: SD Card detect pin */
|
GPIO_InitStructure.GPIO_Pin = SD_DETECT_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
|
GPIO_Init(SD_DETECT_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< SD_SPI Config */
|
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
|
SPI_InitStructure.SPI_Mode = SPI_Mode_Master;
|
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
|
SPI_InitStructure.SPI_CPOL = SPI_CPOL_High;
|
SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
|
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
|
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_2;
|
|
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
|
SPI_InitStructure.SPI_CRCPolynomial = 7;
|
SPI_Init(SD_SPI, &SPI_InitStructure);
|
|
SPI_Cmd(SD_SPI, ENABLE); /*!< SD_SPI enable */
|
}
|
|
/**
|
* @brief DeInitializes the peripherals used by the SPI FLASH driver.
|
* @param None
|
* @retval None
|
*/
|
void sFLASH_LowLevel_DeInit(void)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
/*!< Disable the sFLASH_SPI */
|
SPI_Cmd(sFLASH_SPI, DISABLE);
|
|
/*!< DeInitializes the sFLASH_SPI */
|
SPI_I2S_DeInit(sFLASH_SPI);
|
|
/*!< sFLASH_SPI Periph clock disable */
|
RCC_APB2PeriphClockCmd(sFLASH_SPI_CLK, DISABLE);
|
|
/*!< Configure sFLASH_SPI pins: SCK */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_SPI_SCK_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_Init(sFLASH_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure sFLASH_SPI pins: MISO */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_SPI_MISO_PIN;
|
GPIO_Init(sFLASH_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure sFLASH_SPI pins: MOSI */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_SPI_MOSI_PIN;
|
GPIO_Init(sFLASH_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure sFLASH_CS_PIN pin: sFLASH Card CS pin */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_CS_PIN;
|
GPIO_Init(sFLASH_CS_GPIO_PORT, &GPIO_InitStructure);
|
}
|
|
/**
|
* @brief Initializes the peripherals used by the SPI FLASH driver.
|
* @param None
|
* @retval None
|
*/
|
void sFLASH_LowLevel_Init(void)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
/*!< sFLASH_SPI_CS_GPIO, sFLASH_SPI_MOSI_GPIO, sFLASH_SPI_MISO_GPIO
|
and sFLASH_SPI_SCK_GPIO Periph clock enable */
|
RCC_APB2PeriphClockCmd(sFLASH_CS_GPIO_CLK | sFLASH_SPI_MOSI_GPIO_CLK | sFLASH_SPI_MISO_GPIO_CLK |
|
sFLASH_SPI_SCK_GPIO_CLK, ENABLE);
|
|
/*!< sFLASH_SPI Periph clock enable */
|
RCC_APB2PeriphClockCmd(sFLASH_SPI_CLK, ENABLE);
|
|
/*!< Configure sFLASH_SPI pins: SCK */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_SPI_SCK_PIN;
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
|
GPIO_Init(sFLASH_SPI_SCK_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure sFLASH_SPI pins: MOSI */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_SPI_MOSI_PIN;
|
GPIO_Init(sFLASH_SPI_MOSI_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure sFLASH_SPI pins: MISO */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_SPI_MISO_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_Init(sFLASH_SPI_MISO_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure sFLASH_CS_PIN pin: sFLASH Card CS pin */
|
GPIO_InitStructure.GPIO_Pin = sFLASH_CS_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;
|
GPIO_Init(sFLASH_CS_GPIO_PORT, &GPIO_InitStructure);
|
}
|
|
/**
|
* @brief DeInitializes the LM75_I2C.
|
* @param None
|
* @retval None
|
*/
|
void LM75_LowLevel_DeInit(void)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
/*!< Disable LM75_I2C */
|
I2C_Cmd(LM75_I2C, DISABLE);
|
/*!< DeInitializes the LM75_I2C */
|
I2C_DeInit(LM75_I2C);
|
|
/*!< LM75_I2C Periph clock disable */
|
RCC_APB1PeriphClockCmd(LM75_I2C_CLK, DISABLE);
|
|
/*!< Configure LM75_I2C pins: SCL */
|
GPIO_InitStructure.GPIO_Pin = LM75_I2C_SCL_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
|
GPIO_Init(LM75_I2C_SCL_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure LM75_I2C pins: SDA */
|
GPIO_InitStructure.GPIO_Pin = LM75_I2C_SDA_PIN;
|
GPIO_Init(LM75_I2C_SDA_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure LM75_I2C pin: SMBUS ALERT */
|
GPIO_InitStructure.GPIO_Pin = LM75_I2C_SMBUSALERT_PIN;
|
GPIO_Init(LM75_I2C_SMBUSALERT_GPIO_PORT, &GPIO_InitStructure);
|
}
|
|
/**
|
* @brief Initializes the LM75_I2C..
|
* @param None
|
* @retval None
|
*/
|
void LM75_LowLevel_Init(void)
|
{
|
GPIO_InitTypeDef GPIO_InitStructure;
|
|
/*!< LM75_I2C Periph clock enable */
|
RCC_APB1PeriphClockCmd(LM75_I2C_CLK, ENABLE);
|
|
/*!< LM75_I2C_SCL_GPIO_CLK, LM75_I2C_SDA_GPIO_CLK
|
and LM75_I2C_SMBUSALERT_GPIO_CLK Periph clock enable */
|
RCC_APB2PeriphClockCmd(LM75_I2C_SCL_GPIO_CLK | LM75_I2C_SDA_GPIO_CLK |
|
LM75_I2C_SMBUSALERT_GPIO_CLK, ENABLE);
|
|
/*!< Configure LM75_I2C pins: SCL */
|
GPIO_InitStructure.GPIO_Pin = LM75_I2C_SCL_PIN;
|
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
|
GPIO_Init(LM75_I2C_SCL_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure LM75_I2C pins: SDA */
|
GPIO_InitStructure.GPIO_Pin = LM75_I2C_SDA_PIN;
|
GPIO_Init(LM75_I2C_SDA_GPIO_PORT, &GPIO_InitStructure);
|
|
/*!< Configure LM75_I2C pin: SMBUS ALERT */
|
GPIO_InitStructure.GPIO_Pin = LM75_I2C_SMBUSALERT_PIN;
|
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;
|
GPIO_Init(LM75_I2C_SMBUSALERT_GPIO_PORT, &GPIO_InitStructure);
|
}
|
|
/**
|
* @}
|
*/
|
|
|
/**
|
* @}
|
*/
|
|
/**
|
* @}
|
*/
|
|
/**
|
* @}
|
*/
|
|
/**
|
* @}
|
*/
|
|
/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
|
