/*! ------------------------------------------------------------------------------------------------------------------
|
* @file deca_regs.h
|
* @brief DW1000 Register Definitions
|
* This file supports assembler and C development for DW1000 enabled devices
|
*
|
* @attention
|
*
|
* Copyright 2013 (c) DecaWave Ltd, Dublin, Ireland.
|
*
|
* All rights reserved.
|
*
|
*/
|
|
#ifndef _DECA_REGS_H_
|
#define _DECA_REGS_H_
|
|
#ifdef __cplusplus
|
extern "C" {
|
#endif
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register DEV_ID
|
**/
|
#define DEV_ID_ID 0x00 /* Device ID register, includes revision info (0xDECA0130) */
|
#define DEV_ID_LEN (4)
|
/* mask and shift */
|
#define DEV_ID_REV_MASK 0x0000000FUL /* Revision */
|
#define DEV_ID_VER_MASK 0x000000F0UL /* Version */
|
#define DEV_ID_MODEL_MASK 0x0000FF00UL /* The MODEL identifies the device. The DW1000 is device type 0x01 */
|
#define DEV_ID_RIDTAG_MASK 0xFFFF0000UL /* Register Identification Tag 0XDECA */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register EUI_64
|
**/
|
#define EUI_64_ID 0x01 /* IEEE Extended Unique Identifier (63:0) */
|
#define EUI_64_LEN (8)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register PANADR
|
**/
|
#define PANADR_ID 0x03 /* PAN ID (31:16) and Short Address (15:0) */
|
#define PANADR_LEN (4)
|
/*mask and shift */
|
#define PANADR_SHORT_ADDR_MASK 0x0000FFFFUL /* Short Address */
|
#define PANADR_PAN_ID_MASK 0xFFFF00F0UL /* PAN Identifier */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x05
|
**/
|
#define REG_05_ID_RESERVED 0x05
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register SYS_CFG
|
**/
|
#define SYS_CFG_ID 0x04 /* System Configuration (31:0) */
|
#define SYS_CFG_LEN (4)
|
/*mask and shift */
|
#define SYS_CFG_MASK 0xF047FFFFUL /* access mask to SYS_CFG_ID */
|
#define SYS_CFG_FF_ALL_EN 0x000001FEUL /* Frame filtering options all frames allowed */
|
/*offset 0 */
|
#define SYS_CFG_FFE 0x00000001UL /* Frame Filtering Enable. This bit enables the frame filtering functionality */
|
#define SYS_CFG_FFBC 0x00000002UL /* Frame Filtering Behave as a Co-ordinator */
|
#define SYS_CFG_FFAB 0x00000004UL /* Frame Filtering Allow Beacon frame reception */
|
#define SYS_CFG_FFAD 0x00000008UL /* Frame Filtering Allow Data frame reception */
|
#define SYS_CFG_FFAA 0x00000010UL /* Frame Filtering Allow Acknowledgment frame reception */
|
#define SYS_CFG_FFAM 0x00000020UL /* Frame Filtering Allow MAC command frame reception */
|
#define SYS_CFG_FFAR 0x00000040UL /* Frame Filtering Allow Reserved frame types */
|
#define SYS_CFG_FFA4 0x00000080UL /* Frame Filtering Allow frames with frame type field of 4, (binary 100) */
|
/*offset 8 */
|
#define SYS_CFG_FFA5 0x00000100UL /* Frame Filtering Allow frames with frame type field of 5, (binary 101) */
|
#define SYS_CFG_HIRQ_POL 0x00000200UL /* Host interrupt polarity */
|
#define SYS_CFG_SPI_EDGE 0x00000400UL /* SPI data launch edge */
|
#define SYS_CFG_DIS_FCE 0x00000800UL /* Disable frame check error handling */
|
#define SYS_CFG_DIS_DRXB 0x00001000UL /* Disable Double RX Buffer */
|
#define SYS_CFG_DIS_PHE 0x00002000UL /* Disable receiver abort on PHR error */
|
#define SYS_CFG_DIS_RSDE 0x00004000UL /* Disable Receiver Abort on RSD error */
|
#define SYS_CFG_FCS_INIT2F 0x00008000UL /* initial seed value for the FCS generation and checking function */
|
/*offset 16 */
|
#define SYS_CFG_PHR_MODE_00 0x00000000UL /* Standard Frame mode */
|
#define SYS_CFG_PHR_MODE_11 0x00030000UL /* Long Frames mode */
|
#define SYS_CFG_DIS_STXP 0x00040000UL /* Disable Smart TX Power control */
|
#define SYS_CFG_RXM110K 0x00400000UL /* Receiver Mode 110 kbps data rate */
|
/*offset 24 */
|
#define SYS_CFG_RXWTOE 0x10000000UL /* Receive Wait Timeout Enable. */
|
#define SYS_CFG_RXAUTR 0x20000000UL /* Receiver Auto-Re-enable. This bit is used to cause the receiver to re-enable automatically */
|
#define SYS_CFG_AUTOACK 0x40000000UL /* Automatic Acknowledgement Enable */
|
#define SYS_CFG_AACKPEND 0x80000000UL /* Automatic Acknowledgement Pending bit control */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register SYS_TIME
|
**/
|
#define SYS_TIME_ID 0x06 /* System Time Counter (40-bit) */
|
#define SYS_TIME_LEN (5) /* Note 40 bit register */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x07
|
**/
|
#define REG_07_ID_RESERVED 0x07
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register TX_FCTRL
|
**/
|
#define TX_FCTRL_ID 0x08 /* Transmit Frame Control */
|
#define TX_FCTRL_LEN (5) /* Note 40 bit register */
|
/*masks (low 32 bit) */
|
#define TX_FCTRL_TFLEN_MASK 0x0000007FUL /* bit mask to access Transmit Frame Length */
|
#define TX_FCTRL_TFLE_MASK 0x00000380UL /* bit mask to access Transmit Frame Length Extension */
|
#define TX_FCTRL_FLE_MASK 0x000003FFUL /* bit mask to access Frame Length field */
|
#define TX_FCTRL_TXBR_MASK 0x00006000UL /* bit mask to access Transmit Bit Rate */
|
#define TX_FCTRL_TXPRF_MASK 0x00030000UL /* bit mask to access Transmit Pulse Repetition Frequency */
|
#define TX_FCTRL_TXPSR_MASK 0x000C0000UL /* bit mask to access Transmit Preamble Symbol Repetitions (PSR). */
|
#define TX_FCTRL_PE_MASK 0x00300000UL /* bit mask to access Preamble Extension */
|
#define TX_FCTRL_TXPSR_PE_MASK 0x003C0000UL /* bit mask to access Transmit Preamble Symbol Repetitions (PSR). */
|
#define TX_FCTRL_SAFE_MASK_32 0xFFFFE3FFUL /* FSCTRL has fields which should always be writen zero */
|
/*offset 0 */
|
/*offset 8 */
|
#define TX_FCTRL_TXBR_110k 0x00000000UL /* Transmit Bit Rate = 110k */
|
#define TX_FCTRL_TXBR_850k 0x00002000UL /* Transmit Bit Rate = 850k */
|
#define TX_FCTRL_TXBR_6M 0x00004000UL /* Transmit Bit Rate = 6.8M */
|
#define TX_FCTRL_TXBR_SHFT (13) /* shift to access Data Rate field */
|
#define TX_FCTRL_TR 0x00008000UL /* Transmit Ranging enable */
|
#define TX_FCTRL_TR_SHFT (15) /* shift to access Ranging bit */
|
/*offset 16 */
|
#define TX_FCTRL_TXPRF_SHFT (16) /* shift to access Pulse Repetition Frequency field */
|
#define TX_FCTRL_TXPRF_4M 0x00000000UL /* Transmit Pulse Repetition Frequency = 4 Mhz */
|
#define TX_FCTRL_TXPRF_16M 0x00010000UL /* Transmit Pulse Repetition Frequency = 16 Mhz */
|
#define TX_FCTRL_TXPRF_64M 0x00020000UL /* Transmit Pulse Repetition Frequency = 64 Mhz */
|
#define TX_FCTRL_TXPSR_SHFT (18) /* shift to access Preamble Symbol Repetitions field */
|
#define TX_FCTRL_PE_SHFT (20) /* shift to access Preamble length Extension to allow specification of non-standard values */
|
#define TX_FCTRL_TXPSR_PE_16 0x00000000UL /* bit mask to access Preamble Extension = 16 */
|
#define TX_FCTRL_TXPSR_PE_64 0x00040000UL /* bit mask to access Preamble Extension = 64 */
|
#define TX_FCTRL_TXPSR_PE_128 0x00140000UL /* bit mask to access Preamble Extension = 128 */
|
#define TX_FCTRL_TXPSR_PE_256 0x00240000UL /* bit mask to access Preamble Extension = 256 */
|
#define TX_FCTRL_TXPSR_PE_512 0x00340000UL /* bit mask to access Preamble Extension = 512 */
|
#define TX_FCTRL_TXPSR_PE_1024 0x00080000UL /* bit mask to access Preamble Extension = 1024 */
|
#define TX_FCTRL_TXPSR_PE_1536 0x00180000UL /* bit mask to access Preamble Extension = 1536 */
|
#define TX_FCTRL_TXPSR_PE_2048 0x00280000UL /* bit mask to access Preamble Extension = 2048 */
|
#define TX_FCTRL_TXPSR_PE_4096 0x000C0000UL /* bit mask to access Preamble Extension = 4096 */
|
/*offset 24 */
|
#define TX_FCTRL_TXBOFFS_MASK 0xFF000000UL /* bit mask to access Transmit buffer index offset 10-bit field */
|
/*offset 32 */
|
#define TX_FCTRL_IFSDELAY_MASK 0xFF00000000ULL /* bit mask to access Inter-Frame Spacing field */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register TX_BUFFER
|
**/
|
#define TX_BUFFER_ID 0x09 /* Transmit Data Buffer */
|
#define TX_BUFFER_LEN (1024)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register DX_TIME
|
**/
|
#define DX_TIME_ID 0x0A /* Delayed Send or Receive Time (40-bit) */
|
#define DX_TIME_LEN (5)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x08
|
**/
|
#define REG_0B_ID_RESERVED 0x0B
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_FWTO
|
**/
|
#define RX_FWTO_ID 0x0C /* Receive Frame Wait Timeout Period */
|
#define RX_FWTO_LEN (2) /* doc bug*/
|
/*mask and shift */
|
#define RX_FWTO_MASK 0xFFFF
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register SYS_CTRL
|
**/
|
#define SYS_CTRL_ID 0x0D /* System Control Register */
|
#define SYS_CTRL_LEN (4)
|
/*masks */
|
#define SYS_CTRL_MASK_32 0x010003CFUL /* System Control Register access mask (all unused fields should always be writen as zero) */
|
/*offset 0 */
|
#define SYS_CTRL_SFCST 0x00000001UL /* Suppress Auto-FCS Transmission (on this frame) */
|
#define SYS_CTRL_TXSTRT 0x00000002UL /* Start Transmitting Now */
|
#define SYS_CTRL_TXDLYS 0x00000004UL /* Transmitter Delayed Sending (initiates sending when SYS_TIME == TXD_TIME */
|
#define SYS_CTRL_CANSFCS 0x00000008UL /* Cancel Suppression of auto-FCS transmission (on the current frame) */
|
#define SYS_CTRL_TRXOFF 0x00000040UL /* Transceiver Off. Force Transciever OFF abort TX or RX immediately */
|
#define SYS_CTRL_WAIT4RESP 0x00000080UL /* Wait for Response */
|
/*offset 8 */
|
#define SYS_CTRL_RXENAB 0x00000100UL /* Enable Receiver Now */
|
#define SYS_CTRL_RXDLYE 0x00000200UL /* Receiver Delayed Enable (Enables Receiver when SY_TIME[0x??] == RXD_TIME[0x??] CHECK comment*/
|
/*offset 16 */
|
/*offset 24 */
|
#define SYS_CTRL_HSRBTOGGLE 0x01000000UL /* Host side receiver buffer pointer toggle - toggles 0/1 host side data set pointer */
|
#define SYS_CTRL_HRBT (SYS_CTRL_HSRBTOGGLE)
|
#define SYS_CTRL_HRBT_OFFSET (3)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register SYS_MASK
|
**/
|
#define SYS_MASK_ID 0x0E /* System Event Mask Register */
|
#define SYS_MASK_LEN (4)
|
/*masks */
|
#define SYS_MASK_MASK_32 0x3FF7FFFEUL /* System Event Mask Register access mask (all unused fields should always be writen as zero) */
|
/*offset 0 */
|
#define SYS_MASK_MCPLOCK 0x00000002UL /* Mask clock PLL lock event */
|
#define SYS_MASK_MESYNCR 0x00000004UL /* Mask clock PLL lock event */
|
#define SYS_MASK_MAAT 0x00000008UL /* Mask automatic acknowledge trigger event */
|
#define SYS_MASK_MTXFRB 0x00000010UL /* Mask transmit frame begins event */
|
#define SYS_MASK_MTXPRS 0x00000020UL /* Mask transmit preamble sent event */
|
#define SYS_MASK_MTXPHS 0x00000040UL /* Mask transmit PHY Header Sent event */
|
#define SYS_MASK_MTXFRS 0x00000080UL /* Mask transmit frame sent event */
|
/*offset 8 */
|
#define SYS_MASK_MRXPRD 0x00000100UL /* Mask receiver preamble detected event */
|
#define SYS_MASK_MRXSFDD 0x00000200UL /* Mask receiver SFD detected event */
|
#define SYS_MASK_MLDEDONE 0x00000400UL /* Mask LDE processing done event */
|
#define SYS_MASK_MRXPHD 0x00000800UL /* Mask receiver PHY header detect event */
|
#define SYS_MASK_MRXPHE 0x00001000UL /* Mask receiver PHY header error event */
|
#define SYS_MASK_MRXDFR 0x00002000UL /* Mask receiver data frame ready event */
|
#define SYS_MASK_MRXFCG 0x00004000UL /* Mask receiver FCS good event */
|
#define SYS_MASK_MRXFCE 0x00008000UL /* Mask receiver FCS error event */
|
/*offset 16 */
|
#define SYS_MASK_MRXRFSL 0x00010000UL /* Mask receiver Reed Solomon Frame Sync Loss event */
|
#define SYS_MASK_MRXRFTO 0x00020000UL /* Mask Receive Frame Wait Timeout event */
|
#define SYS_MASK_MLDEERR 0x00040000UL /* Mask leading edge detection processing error event */
|
#define SYS_MASK_MRXOVRR 0x00100000UL /* Mask Receiver Overrun event */
|
#define SYS_MASK_MRXPTO 0x00200000UL /* Mask Preamble detection timeout event */
|
#define SYS_MASK_MGPIOIRQ 0x00400000UL /* Mask GPIO interrupt event */
|
#define SYS_MASK_MSLP2INIT 0x00800000UL /* Mask SLEEP to INIT event */
|
/*offset 24*/
|
#define SYS_MASK_MRFPLLLL 0x01000000UL /* Mask RF PLL Loosing Lock warning event */
|
#define SYS_MASK_MCPLLLL 0x02000000UL /* Mask Clock PLL Loosing Lock warning event */
|
#define SYS_MASK_MRXSFDTO 0x04000000UL /* Mask Receive SFD timeout event */
|
#define SYS_MASK_MHPDWARN 0x08000000UL /* Mask Half Period Delay Warning event */
|
#define SYS_MASK_MTXBERR 0x10000000UL /* Mask Transmit Buffer Error event */
|
#define SYS_MASK_MAFFREJ 0x20000000UL /* Mask Automatic Frame Filtering rejection event */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register SYS_STATUS
|
**/
|
#define SYS_STATUS_ID 0x0F /* System event Status Register */
|
#define SYS_STATUS_LEN (5) /* Note 40 bit register */
|
/*masks */
|
#define SYS_STATUS_MASK_32 0xFFF7FFFFUL /* System event Status Register access mask (all unused fields should always be writen as zero) */
|
/*offset 0 */
|
#define SYS_STATUS_IRQS 0x00000001UL /* Interrupt Request Status READ ONLY */
|
#define SYS_STATUS_CPLOCK 0x00000002UL /* Clock PLL Lock */
|
#define SYS_STATUS_ESYNCR 0x00000004UL /* External Sync Clock Reset */
|
#define SYS_STATUS_AAT 0x00000008UL /* Automatic Acknowledge Trigger */
|
#define SYS_STATUS_TXFRB 0x00000010UL /* Transmit Frame Begins */
|
#define SYS_STATUS_TXPRS 0x00000020UL /* Transmit Preamble Sent */
|
#define SYS_STATUS_TXPHS 0x00000040UL /* Transmit PHY Header Sent */
|
#define SYS_STATUS_TXFRS 0x00000080UL /* Transmit Frame Sent: This is set when the transmitter has completed the sending of a frame */
|
/*offset 8 */
|
#define SYS_STATUS_RXPRD 0x00000100UL /* Receiver Preamble Detected status */
|
#define SYS_STATUS_RXSFDD 0x00000200UL /* Receiver Start Frame Delimiter Detected. */
|
#define SYS_STATUS_LDEDONE 0x00000400UL /* LDE processing done */
|
#define SYS_STATUS_RXPHD 0x00000800UL /* Receiver PHY Header Detect */
|
#define SYS_STATUS_RXPHE 0x00001000UL /* Receiver PHY Header Error */
|
#define SYS_STATUS_RXDFR 0x00002000UL /* Receiver Data Frame Ready */
|
#define SYS_STATUS_RXFCG 0x00004000UL /* Receiver FCS Good */
|
#define SYS_STATUS_RXFCE 0x00008000UL /* Receiver FCS Error */
|
/*offset 16 */
|
#define SYS_STATUS_RXRFSL 0x00010000UL /* Receiver Reed Solomon Frame Sync Loss */
|
#define SYS_STATUS_RXRFTO 0x00020000UL /* Receive Frame Wait Timeout */
|
#define SYS_STATUS_LDEERR 0x00040000UL /* Leading edge detection processing error */
|
#define SYS_STATUS_reserved 0x00080000UL /* bit19 reserved */
|
#define SYS_STATUS_RXOVRR 0x00100000UL /* Receiver Overrun */
|
#define SYS_STATUS_RXPTO 0x00200000UL /* Preamble detection timeout */
|
#define SYS_STATUS_GPIOIRQ 0x00400000UL /* GPIO interrupt */
|
#define SYS_STATUS_SLP2INIT 0x00800000UL /* SLEEP to INIT */
|
/*offset 24 */
|
#define SYS_STATUS_RFPLL_LL 0x01000000UL /* RF PLL Losing Lock */
|
#define SYS_STATUS_CLKPLL_LL 0x02000000UL /* Clock PLL Losing Lock */
|
#define SYS_STATUS_RXSFDTO 0x04000000UL /* Receive SFD timeout */
|
#define SYS_STATUS_HPDWARN 0x08000000UL /* Half Period Delay Warning */
|
#define SYS_STATUS_TXBERR 0x10000000UL /* Transmit Buffer Error */
|
#define SYS_STATUS_AFFREJ 0x20000000UL /* Automatic Frame Filtering rejection */
|
#define SYS_STATUS_HSRBP 0x40000000UL /* Host Side Receive Buffer Pointer */
|
#define SYS_STATUS_ICRBP 0x80000000UL /* IC side Receive Buffer Pointer READ ONLY */
|
/*offset 32 */
|
#define SYS_STATUS_RXRSCS 0x0100000000ULL /* Receiver Reed-Solomon Correction Status */
|
#define SYS_STATUS_RXPREJ 0x0200000000ULL /* Receiver Preamble Rejection */
|
#define SYS_STATUS_TXPUTE 0x0400000000ULL /* Transmit power up time error */
|
|
#define SYS_STATUS_TXERR (0x0408) /* These bits are the 16 high bits of status register TXPUTE and HPDWARN flags */
|
|
/* All RX events after a correct packet reception mask. */
|
#define SYS_STATUS_ALL_RX_GOOD (SYS_STATUS_RXDFR | SYS_STATUS_RXFCG | SYS_STATUS_RXPRD | \
|
SYS_STATUS_RXSFDD | SYS_STATUS_RXPHD | SYS_STATUS_LDEDONE)
|
|
/* All double buffer events mask. */
|
#define SYS_STATUS_ALL_DBLBUFF (SYS_STATUS_RXDFR | SYS_STATUS_RXFCG)
|
|
/* All RX errors mask. */
|
#define SYS_STATUS_ALL_RX_ERR (SYS_STATUS_RXPHE | SYS_STATUS_RXFCE | SYS_STATUS_RXRFSL | SYS_STATUS_RXSFDTO \
|
| SYS_STATUS_RXRFTO | SYS_STATUS_RXPTO | SYS_STATUS_AFFREJ | SYS_STATUS_LDEERR)
|
|
/* All TX events mask. */
|
#define SYS_STATUS_ALL_TX (SYS_STATUS_AAT | SYS_STATUS_TXFRB | SYS_STATUS_TXPRS | \
|
SYS_STATUS_TXPHS | SYS_STATUS_TXFRS )
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_FINFO
|
**/
|
#define RX_FINFO_ID 0x10 /* RX Frame Information (in double buffer set) */
|
#define RX_FINFO_LEN (4)
|
/*mask and shift */
|
#define RX_FINFO_MASK_32 0xFFFFFBFFUL /* System event Status Register access mask (all unused fields should always be writen as zero) */
|
#define RX_FINFO_RXFLEN_MASK 0x0000007FUL /* Receive Frame Length (0 to 127) */
|
#define RX_FINFO_RXFLE_MASK 0x00000380UL /* Receive Frame Length Extension (0 to 7)<<7 */
|
#define RX_FINFO_RXFL_MASK_1023 0x000003FFUL /* Receive Frame Length Extension (0 to 1023) */
|
|
#define RX_FINFO_RXNSPL_MASK 0x00001800UL /* Receive Non-Standard Preamble Length */
|
#define RX_FINFO_RXPSR_MASK 0x000C0000UL /* RX Preamble Repetition. 00 = 16 symbols, 01 = 64 symbols, 10 = 1024 symbols, 11 = 4096 symbols */
|
|
#define RX_FINFO_RXPEL_MASK 0x000C1800UL /* Receive Preamble Length = RXPSR+RXNSPL */
|
#define RX_FINFO_RXPEL_64 0x00040000UL /* Receive Preamble length = 64 */
|
#define RX_FINFO_RXPEL_128 0x00040800UL /* Receive Preamble length = 128 */
|
#define RX_FINFO_RXPEL_256 0x00041000UL /* Receive Preamble length = 256 */
|
#define RX_FINFO_RXPEL_512 0x00041800UL /* Receive Preamble length = 512 */
|
#define RX_FINFO_RXPEL_1024 0x00080000UL /* Receive Preamble length = 1024 */
|
#define RX_FINFO_RXPEL_1536 0x00080800UL /* Receive Preamble length = 1536 */
|
#define RX_FINFO_RXPEL_2048 0x00081000UL /* Receive Preamble length = 2048 */
|
#define RX_FINFO_RXPEL_4096 0x000C0000UL /* Receive Preamble length = 4096 */
|
|
#define RX_FINFO_RXBR_MASK 0x00006000UL /* Receive Bit Rate report. This field reports the received bit rate */
|
#define RX_FINFO_RXBR_110k 0x00000000UL /* Received bit rate = 110 kbps */
|
#define RX_FINFO_RXBR_850k 0x00002000UL /* Received bit rate = 850 kbps */
|
#define RX_FINFO_RXBR_6M 0x00004000UL /* Received bit rate = 6.8 Mbps */
|
#define RX_FINFO_RXBR_SHIFT (13)
|
|
#define RX_FINFO_RNG 0x00008000UL /* Receiver Ranging. Ranging bit in the received PHY header identifying the frame as a ranging packet. */
|
#define RX_FINFO_RNG_SHIFT (15)
|
|
#define RX_FINFO_RXPRF_MASK 0x00030000UL /* RX Pulse Repetition Rate report */
|
#define RX_FINFO_RXPRF_16M 0x00010000UL /* PRF being employed in the receiver = 16M */
|
#define RX_FINFO_RXPRF_64M 0x00020000UL /* PRF being employed in the receiver = 64M */
|
#define RX_FINFO_RXPRF_SHIFT (16)
|
|
#define RX_FINFO_RXPACC_MASK 0xFFF00000UL /* Preamble Accumulation Count */
|
#define RX_FINFO_RXPACC_SHIFT (20)
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_BUFFER
|
**/
|
#define RX_BUFFER_ID 0x11 /* Receive Data Buffer (in double buffer set) */
|
#define RX_BUFFER_LEN (1024)
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_FQUAL
|
**/
|
#define RX_FQUAL_ID 0x12 /* Rx Frame Quality information (in double buffer set) */
|
#define RX_FQUAL_LEN (8) /* note 64 bit register*/
|
/*mask and shift */
|
/*offset 0 */
|
#define RX_EQUAL_STD_NOISE_MASK 0x0000FFFFULL /* Standard Deviation of Noise */
|
#define RX_EQUAL_STD_NOISE_SHIFT (0)
|
#define STD_NOISE_MASK RX_EQUAL_STD_NOISE_MASK
|
#define STD_NOISE_SHIFT RX_EQUAL_STD_NOISE_SHIFT
|
/*offset 16 */
|
#define RX_EQUAL_FP_AMPL2_MASK 0xFFFF0000ULL /* First Path Amplitude point 2 */
|
#define RX_EQUAL_FP_AMPL2_SHIFT (16)
|
#define FP_AMPL2_MASK RX_EQUAL_FP_AMPL2_MASK
|
#define FP_AMPL2_SHIFT RX_EQUAL_FP_AMPL2_SHIFT
|
/*offset 32*/
|
#define RX_EQUAL_PP_AMPL3_MASK 0x0000FFFF00000000ULL /* First Path Amplitude point 3 */
|
#define RX_EQUAL_PP_AMPL3_SHIFT (32)
|
#define PP_AMPL3_MASK RX_EQUAL_PP_AMPL3_MASK
|
#define PP_AMPL3_SHIFT RX_EQUAL_PP_AMPL3_SHIFT
|
/*offset 48*/
|
#define RX_EQUAL_CIR_MXG_MASK 0xFFFF000000000000ULL /* Channel Impulse Response Max Growth */
|
#define RX_EQUAL_CIR_MXG_SHIFT (48)
|
#define CIR_MXG_MASK RX_EQUAL_CIR_MXG_MASK
|
#define CIR_MXG_SHIFT RX_EQUAL_CIR_MXG_SHIFT
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_TTCKI
|
* The value here is the interval over which the timing offset reported
|
* in the RXTOFS field of Register file: 0x14 ?RX_TTCKO is measured.
|
* The clock offset is calculated by dividing RXTTCKI by RXTOFS.
|
* The value in RXTTCKI will take just one of two values depending on the PRF: 0x01F00000 @ 16 MHz PRF,
|
* and 0x01FC0000 @ 64 MHz PRF.
|
**/
|
#define RX_TTCKI_ID 0x13 /* Receiver Time Tracking Interval (in double buffer set) */
|
#define RX_TTCKI_LEN (4)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_TTCKO
|
**/
|
#define RX_TTCKO_ID 0x14 /* Receiver Time Tracking Offset (in double buffer set) */
|
#define RX_TTCKO_LEN (5) /* Note 40 bit register */
|
/*mask and shift */
|
#define RX_TTCKO_MASK_32 0xFF07FFFFUL /* Receiver Time Tracking Offset access mask (all unused fields should always be writen as zero) */
|
/*offset 0 */
|
#define RX_TTCKO_RXTOFS_MASK 0x0007FFFFUL /* RX time tracking offset. This RXTOFS value is a 19-bit signed quantity*/
|
/*offset 24 */
|
#define RX_TTCKO_RSMPDEL_MASK 0xFF000000UL /* This 8-bit field reports an internal re-sampler delay value */
|
/*offset 32 */
|
#define RX_TTCKO_RCPHASE_MASK 0x7F0000000000ULL /* This 7-bit field reports the receive carrier phase adjustment at time the ranging timestamp is made. */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_TIME
|
**/
|
#define RX_TIME_ID 0x15 /* Receive Message Time of Arrival (in double buffer set) */
|
#define RX_TIME_LLEN (14)
|
#define RX_TIME_RX_STAMP_LEN (5) /* read only 5 bytes (the adjusted timestamp (40:0)) */
|
#define RX_STAMP_LEN RX_TIME_RX_STAMP_LEN
|
/*mask and shift */
|
#define RX_TIME_RX_STAMP_OFFSET (0) /* byte 0..4 40 bit Reports the fully adjusted time of reception. */
|
#define RX_TIME_FP_INDEX_OFFSET (5) /* byte 5..6 16 bit First path index. */
|
#define RX_TIME_FP_AMPL1_OFFSET (7) /* byte 7..8 16 bit First Path Amplitude point 1 */ /* doc bug */
|
#define RX_TIME_FP_RAWST_OFFSET (9) /* byte 9..13 40 bit Raw Timestamp for the frame */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register
|
**/
|
#define REG_16_ID_RESERVED 0x16
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register
|
**/
|
#define TX_TIME_ID 0x17 /* Transmit Message Time of Sending */
|
#define TX_TIME_LLEN (10)
|
#define TX_TIME_TX_STAMP_LEN (5) /* 40-bits = 5 bytes */
|
#define TX_STAMP_LEN TX_TIME_TX_STAMP_LEN
|
/*mask and shift */
|
#define TX_TIME_TX_STAMP_OFFSET (0) /* byte 0..4 40 bit Reports the fully adjusted time of transmission */
|
#define TX_TIME_TX_RAWST_OFFSET (5) /* byte 5..9 40 bit Raw Timestamp for the frame */
|
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register TX_ANTD
|
**/
|
#define TX_ANTD_ID 0x18 /* 16-bit Delay from Transmit to Antenna */
|
#define TX_ANTD_LEN (2) /* doc bug */
|
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register SYS_STATES
|
* Register map register file 0x19 is reserved
|
*
|
**/
|
#define SYS_STATE_ID 0x19 /* System State information READ ONLY */
|
#define SYS_STATE_LEN (5)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register ACK_RESP_T
|
**/
|
/* Acknowledge (31:24 preamble symbol delay before auto ACK is sent) and respose (19:0 - unit 1us) timer */
|
#define ACK_RESP_T_ID 0x1A /* Acknowledgement Time and Response Time */
|
#define ACK_RESP_T_LEN (4)
|
/*mask and shift */
|
#define ACK_RESP_T_MASK 0xFF0FFFFFUL /* Acknowledgement Time and Response access mask */
|
#define ACK_RESP_T_W4R_TIM_MASK 0x000FFFFFUL /* Wait-for-Response turn-around Time 20 bit field */
|
#define W4R_TIM_MASK ACK_RESP_T_W4R_TIM_MASK
|
#define ACK_RESP_T_ACK_TIM_MASK 0xFF000000UL /* Auto-Acknowledgement turn-around Time */
|
#define ACK_TIM_MASK ACK_RESP_T_ACK_TIM_MASK
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x1B 0x1C
|
**/
|
#define REG_1B_ID_RESERVED 0x1B
|
#define REG_1C_ID_RESERVED 0x1C
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RX_SNIFF
|
* Sniff Mode Configuration or Pulsed Preamble Reception Configuration
|
**/
|
#define RX_SNIFF_ID 0x1D /* Sniff Mode Configuration */
|
#define RX_SNIFF_LEN (4)
|
/*mask and shift */
|
#define RX_SNIFF_MASK 0x0000FF0FUL /* */
|
#define RX_SNIFF_SNIFF_ONT_MASK 0x0000000FUL /* SNIFF Mode ON time. Specified in units of PAC */
|
#define SNIFF_ONT_MASK RX_SNIFF_SNIFF_ONT_MASK
|
#define RX_SNIFF_SNIFF_OFFT_MASK 0x0000FF00UL /* SNIFF Mode OFF time specified in units of approximately 1mkS, or 128 system clock cycles.*/
|
#define SNIFF_OFFT_MASK RX_SNIFF_SNIFF_OFFT_MASK
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register TX_POWER
|
**/
|
#define TX_POWER_ID 0x1E /* TX Power Control */
|
#define TX_POWER_LEN (4)
|
/*mask and shift definition for Smart Transmit Power Control*/
|
#define TX_POWER_BOOSTNORM_MASK 0x00000000UL /* This is the normal power setting used for frames that do not fall */
|
#define BOOSTNORM_MASK TX_POWER_BOOSTNORM_MASK
|
#define TX_POWER_BOOSTNORM_SHIFT (0)
|
#define TX_POWER_BOOSTP500_MASK 0x00000000UL /* This value sets the power applied during transmission at the 6.8 Mbps data rate frames that are less than 0.5 ms duration */
|
#define BOOSTP500_MASK TX_POWER_BOOSTP500_MASK
|
#define TX_POWER_BOOSTP500_SHIFT (8)
|
#define TX_POWER_BOOSTP250_MASK 0x00000000UL /* This value sets the power applied during transmission at the 6.8 Mbps data rate frames that are less than 0.25 ms duration */
|
#define BOOSTP250_MASK TX_POWER_BOOSTP250_MASK
|
#define TX_POWER_BOOSTP250_SHIFT (16)
|
#define TX_POWER_BOOSTP125_MASK 0x00000000UL /* This value sets the power applied during transmission at the 6.8 Mbps data rate frames that are less than 0.125 ms */
|
#define BOOSTP125_MASK TX_POWER_BOOSTP125_MASK
|
#define TX_POWER_BOOSTP125_SHIFT (24)
|
/*mask and shift definition for Manual Transmit Power Control (DIS_STXP=1 in SYS_CFG)*/
|
#define TX_POWER_MAN_DEFAULT 0x0E080222UL
|
#define TX_POWER_TXPOWPHR_MASK 0x0000FF00UL /* This power setting is applied during the transmission of the PHY header (PHR) portion of the frame. */
|
#define TX_POWER_TXPOWSD_MASK 0x00FF0000UL /* This power setting is applied during the transmission of the synchronisation header (SHR) and data portions of the frame. */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register CHAN_CTRL
|
**/
|
#define CHAN_CTRL_ID 0x1F /* Channel Control */
|
#define CHAN_CTRL_LEN (4)
|
/*mask and shift */
|
#define CHAN_CTRL_MASK 0xFFFF00FFUL /* Channel Control Register access mask */
|
#define CHAN_CTRL_TX_CHAN_MASK 0x0000000FUL /* Supported channels are 1, 2, 3, 4, 5, and 7.*/
|
#define CHAN_CTRL_TX_CHAN_SHIFT (0) /* Bits 0..3 TX channel number 0-15 selection */
|
|
#define CHAN_CTRL_RX_CHAN_MASK 0x000000F0UL
|
#define CHAN_CTRL_RX_CHAN_SHIFT (4) /* Bits 4..7 RX channel number 0-15 selection */
|
|
#define CHAN_CTRL_RXFPRF_MASK 0x000C0000UL /* Bits 18..19 Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */
|
#define CHAN_CTRL_RXFPRF_SHIFT (18)
|
/* Specific RXFPRF configuration */
|
#define CHAN_CTRL_RXFPRF_4 0x00000000UL /* Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */
|
#define CHAN_CTRL_RXFPRF_16 0x00040000UL /* Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */
|
#define CHAN_CTRL_RXFPRF_64 0x00080000UL /* Specify (Force) RX Pulse Repetition Rate: 00 = 4 MHz, 01 = 16 MHz, 10 = 64MHz. */
|
#define CHAN_CTRL_TX_PCOD_MASK 0x07C00000UL /* Bits 22..26 TX Preamble Code selection, 1 to 24. */
|
#define CHAN_CTRL_TX_PCOD_SHIFT (22)
|
#define CHAN_CTRL_RX_PCOD_MASK 0xF8000000UL /* Bits 27..31 RX Preamble Code selection, 1 to 24. */
|
#define CHAN_CTRL_RX_PCOD_SHIFT (27)
|
/*offset 16 */
|
#define CHAN_CTRL_DWSFD 0x00020000UL /* Bit 17 This bit enables a non-standard DecaWave proprietary SFD sequence. */
|
#define CHAN_CTRL_DWSFD_SHIFT (17)
|
#define CHAN_CTRL_TNSSFD 0x00100000UL /* Bit 20 Non-standard SFD in the transmitter */
|
#define CHAN_CTRL_TNSSFD_SHIFT (20)
|
#define CHAN_CTRL_RNSSFD 0x00200000UL /* Bit 21 Non-standard SFD in the receiver */
|
#define CHAN_CTRL_RNSSFD_SHIFT (21)
|
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x20
|
**/
|
#define REG_20_ID_RESERVED 0x20
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register USR_SFD
|
* Please read User Manual : User defined SFD sequence
|
**/
|
#define USR_SFD_ID 0x21 /* User-specified short/long TX/RX SFD sequences */
|
#define USR_SFD_LEN (41)
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register
|
**/
|
#define REG_22_ID_RESERVED 0x22
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register AGC_CTRL
|
* Please take care to write to this register as doing so may cause the DW1000 to malfunction
|
**/
|
#define AGC_CTRL_ID 0x23 /* Automatic Gain Control configuration */
|
#define AGC_CTRL_LEN (32)
|
#define AGC_CFG_STS_ID AGC_CTRL_ID
|
/* offset from AGC_CTRL_ID in bytes */
|
#define AGC_CTRL1_OFFSET (0x02)
|
#define AGC_CTRL1_LEN (2)
|
#define AGC_CTRL1_MASK 0x0001 /* access mask to AGC configuration and control register */
|
#define AGC_CTRL1_DIS_AM 0x0001 /* Disable AGC Measurement. The DIS_AM bit is set by default. */
|
/* offset from AGC_CTRL_ID in bytes */
|
/* Please take care not to write other values to this register as doing so may cause the DW1000 to malfunction */
|
#define AGC_TUNE1_OFFSET (0x04)
|
#define AGC_TUNE1_LEN (2)
|
#define AGC_TUNE1_MASK 0xFFFF /* It is a 16-bit tuning register for the AGC. */
|
#define AGC_TUNE1_16M 0x8870
|
#define AGC_TUNE1_64M 0x889B
|
/* offset from AGC_CTRL_ID in bytes */
|
/* Please take care not to write other values to this register as doing so may cause the DW1000 to malfunction */
|
#define AGC_TUNE2_OFFSET (0x0C)
|
#define AGC_TUNE2_LEN (4)
|
#define AGC_TUNE2_MASK 0xFFFFFFFFUL
|
#define AGC_TUNE2_VAL 0X2502A907UL
|
/* offset from AGC_CTRL_ID in bytes */
|
/* Please take care not to write other values to this register as doing so may cause the DW1000 to malfunction */
|
#define AGC_TUNE3_OFFSET (0x12)
|
#define AGC_TUNE3_LEN (2)
|
#define AGC_TUNE3_MASK 0xFFFF
|
#define AGC_TUNE3_VAL 0X0055
|
/* offset from AGC_CTRL_ID in bytes */
|
#define AGC_STAT1_OFFSET (0x1E)
|
#define AGC_STAT1_LEN (3)
|
#define AGC_STAT1_MASK 0x0FFFFF
|
#define AGC_STAT1_EDG1_MASK 0x0007C0 /* This 5-bit gain value relates to input noise power measurement. */
|
#define AGC_STAT1_EDG2_MASK 0x0FF800 /* This 9-bit value relates to the input noise power measurement. */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register EXT_SYNC
|
**/
|
#define EXT_SYNC_ID 0x24 /* External synchronisation control */
|
#define EXT_SYNC_LEN (12)
|
/* offset from EXT_SYNC_ID in bytes */
|
#define EC_CTRL_OFFSET (0x00)
|
#define EC_CTRL_LEN (4)
|
#define EC_CTRL_MASK 0x00000FFBUL /* sub-register 0x00 is the External clock synchronisation counter configuration register */
|
#define EC_CTRL_OSTSM 0x00000001UL /* External transmit synchronisation mode enable */
|
#define EC_CTRL_OSRSM 0x00000002UL /* External receive synchronisation mode enable */
|
#define EC_CTRL_PLLLCK 0x04 /* PLL lock detect enable */
|
#define EC_CTRL_OSTRM 0x00000800UL /* External timebase reset mode enable */
|
#define EC_CTRL_WAIT_MASK 0x000007F8UL /* Wait counter used for external transmit synchronisation and external timebase reset */
|
/* offset from EXT_SYNC_ID in bytes */
|
#define EC_RXTC_OFFSET (0x04)
|
#define EC_RXTC_LEN (4)
|
#define EC_RXTC_MASK 0xFFFFFFFFUL /* External clock synchronisation counter captured on RMARKER */
|
/* offset from EXT_SYNC_ID in bytes */
|
#define EC_GOLP (0x08)
|
#define EC_GOLP_LEN (4)
|
#define EC_GOLP_MASK 0x0000003FUL /* sub-register 0x08 is the External clock offset to first path 1 GHz counter, EC_GOLP */
|
#define EC_GOLP_OFFSET_EXT_MASK 0x0000003FUL /* This register contains the 1 GHz count from the arrival of the RMARKER and the next edge of the external clock. */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register ACC_MEM
|
**/
|
#define ACC_MEM_ID 0x25 /* Read access to accumulator data */
|
#define ACC_MEM_LEN (4064)
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register GPIO_CTRL
|
**/
|
#define GPIO_CTRL_ID 0x26 /* Peripheral register bus 1 access - GPIO control */
|
#define GPIO_CTRL_LEN (44)
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_MODE_OFFSET 0x00 /* sub-register 0x00 is the GPIO Mode Control Register */
|
#define GPIO_MODE_LEN (4)
|
#define GPIO_MODE_MASK 0x00FFFFC0UL
|
|
#define GPIO_MSGP0_MASK 0x000000C0UL /* Mode Selection for GPIO0/RXOKLED */
|
#define GPIO_MSGP1_MASK 0x00000300UL /* Mode Selection for GPIO1/SFDLED */
|
#define GPIO_MSGP2_MASK 0x00000C00UL /* Mode Selection for GPIO2/RXLED */
|
#define GPIO_MSGP3_MASK 0x00003000UL /* Mode Selection for GPIO3/TXLED */
|
#define GPIO_MSGP4_MASK 0x0000C000UL /* Mode Selection for GPIO4/EXTPA */
|
#define GPIO_MSGP5_MASK 0x00030000UL /* Mode Selection for GPIO5/EXTTXE */
|
#define GPIO_MSGP6_MASK 0x000C0000UL /* Mode Selection for GPIO6/EXTRXE */
|
#define GPIO_MSGP7_MASK 0x00300000UL /* Mode Selection for SYNC/GPIO7 */
|
#define GPIO_MSGP8_MASK 0x00C00000UL /* Mode Selection for IRQ/GPIO8 */
|
|
#define GPIO_PIN5_EXTTXE 0x00010000UL /* The pin operates as the EXTTXE output */
|
#define GPIO_PIN6_EXTRXE 0x00040000UL /* The pin operates as the EXTRXE output */
|
|
#define GPIO_LNA_BYTE_NUM (2) /* byte offset for LNA drive */
|
#define GPIO_PIN5_EXTTXE_8 0x01 /* The pin operates as the EXTTXE output. byte */
|
#define GPIO_PIN6_EXTRXE_8 0x04 /* The pin operates as the EXTRXE output. byte */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_DIR_OFFSET 0x08 /* sub-register 0x08 is the GPIO Direction Control Register */
|
#define GPIO_DIR_LEN (3)
|
#define GPIO_DIR_MASK 0x0011FFFFUL
|
|
#define GxP0 0x00000001UL /* GPIO0 Only changed if the GxM0 mask bit has a value of 1 for the write operation*/
|
#define GxP1 0x00000002UL /* GPIO1. (See GDP0). */
|
#define GxP2 0x00000004UL /* GPIO2. (See GDP0). */
|
#define GxP3 0x00000008UL /* GPIO3. (See GDP0). */
|
#define GxP4 0x00000100UL /* GPIO4. (See GDP0). */
|
#define GxP5 0x00000200UL /* GPIO5. (See GDP0). */
|
#define GxP6 0x00000400UL /* GPIO6. (See GDP0). */
|
#define GxP7 0x00000800UL /* GPIO7. (See GDP0). */
|
#define GxP8 0x00010000UL /* GPIO8 */
|
|
#define GxM0 0x00000010UL /* Mask for GPIO0 */
|
#define GxM1 0x00000020UL /* Mask for GPIO1. (See GDM0). */
|
#define GxM2 0x00000040UL /* Mask for GPIO2. (See GDM0). */
|
#define GxM3 0x00000080UL /* Mask for GPIO3. (See GDM0). */
|
#define GxM4 0x00001000UL /* Mask for GPIO4. (See GDM0). */
|
#define GxM5 0x00002000UL /* Mask for GPIO5. (See GDM0). */
|
#define GxM6 0x00004000UL /* Mask for GPIO6. (See GDM0). */
|
#define GxM7 0x00008000UL /* Mask for GPIO7. (See GDM0). */
|
#define GxM8 0x00100000UL /* Mask for GPIO8. (See GDM0). */
|
|
#define GDP0 GxP0 /* Direction Selection for GPIO0. 1 = input, 0 = output. Only changed if the GDM0 mask bit has a value of 1 for the write operation*/
|
#define GDP1 GxP1 /* Direction Selection for GPIO1. (See GDP0). */
|
#define GDP2 GxP2 /* Direction Selection for GPIO2. (See GDP0). */
|
#define GDP3 GxP3 /* Direction Selection for GPIO3. (See GDP0). */
|
#define GDP4 GxP4 /* Direction Selection for GPIO4. (See GDP0). */
|
#define GDP5 GxP5 /* Direction Selection for GPIO5. (See GDP0). */
|
#define GDP6 GxP6 /* Direction Selection for GPIO6. (See GDP0). */
|
#define GDP7 GxP7 /* Direction Selection for GPIO7. (See GDP0). */
|
#define GDP8 GxP8 /* Direction Selection for GPIO8 */
|
|
#define GDM0 GxM0 /* Mask for setting the direction of GPIO0 */
|
#define GDM1 GxM1 /* Mask for setting the direction of GPIO1. (See GDM0). */
|
#define GDM2 GxM2 /* Mask for setting the direction of GPIO2. (See GDM0). */
|
#define GDM3 GxM3 /* Mask for setting the direction of GPIO3. (See GDM0). */
|
#define GDM4 GxM4 /* Mask for setting the direction of GPIO4. (See GDM0). */
|
#define GDM5 GxM5 /* Mask for setting the direction of GPIO5. (See GDM0). */
|
#define GDM6 GxM6 /* Mask for setting the direction of GPIO6. (See GDM0). */
|
#define GDM7 GxM7 /* Mask for setting the direction of GPIO7. (See GDM0). */
|
#define GDM8 GxM8 /* Mask for setting the direction of GPIO8. (See GDM0). */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_DOUT_OFFSET 0x0C /* sub-register 0x0C is the GPIO data output register. */
|
#define GPIO_DOUT_LEN (3)
|
#define GPIO_DOUT_MASK GPIO_DIR_MASK
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_IRQE_OFFSET 0x10 /* sub-register 0x10 is the GPIO interrupt enable register */
|
#define GPIO_IRQE_LEN (4)
|
#define GPIO_IRQE_MASK 0x000001FFUL
|
#define GIRQx0 0x00000001UL /* IRQ bit0 */
|
#define GIRQx1 0x00000002UL /* IRQ bit1 */
|
#define GIRQx2 0x00000004UL /* IRQ bit2 */
|
#define GIRQx3 0x00000008UL /* IRQ bit3 */
|
#define GIRQx4 0x00000010UL /* IRQ bit4 */
|
#define GIRQx5 0x00000020UL /* IRQ bit5 */
|
#define GIRQx6 0x00000040UL /* IRQ bit6 */
|
#define GIRQx7 0x00000080UL /* IRQ bit7 */
|
#define GIRQx8 0x00000100UL /* IRQ bit8 */
|
#define GIRQE0 GIRQx0 /* GPIO IRQ Enable for GPIO0 input. Value 1 = enable, 0 = disable*/
|
#define GIRQE1 GIRQx1 /* */
|
#define GIRQE2 GIRQx2 /* */
|
#define GIRQE3 GIRQx3 /* */
|
#define GIRQE4 GIRQx4 /* */
|
#define GIRQE5 GIRQx5 /* */
|
#define GIRQE6 GIRQx6 /* */
|
#define GIRQE7 GIRQx7 /* */
|
#define GIRQE8 GIRQx8 /* Value 1 = enable, 0 = disable */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_ISEN_OFFSET 0x14 /* sub-register 0x14 is the GPIO interrupt sense selection register */
|
#define GPIO_ISEN_LEN (4)
|
#define GPIO_ISEN_MASK GPIO_IRQE_MASK
|
#define GISEN0 GIRQx0 /* GPIO IRQ Sense selection GPIO0 input. Value 0 = High or Rising-Edge, 1 = Low or falling-edge.*/
|
#define GISEN1 GIRQx1 /* */
|
#define GISEN2 GIRQx2 /* */
|
#define GISEN3 GIRQx3 /* */
|
#define GISEN4 GIRQx4 /* */
|
#define GISEN5 GIRQx5 /* */
|
#define GISEN6 GIRQx6 /* */
|
#define GISEN7 GIRQx7 /* */
|
#define GISEN8 GIRQx8 /* Value 0 = High or Rising-Edge, 1 = Low or falling-edge */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_IMODE_OFFSET 0x18 /* sub-register 0x18 is the GPIO interrupt mode selection register */
|
#define GPIO_IMODE_LEN (4)
|
#define GPIO_IMODE_MASK GPIO_IRQE_MASK
|
#define GIMOD0 GIRQx0 /* GPIO IRQ Mode selection for GPIO0 input. Value 0 = Level sensitive interrupt. Value 1 = Edge triggered interrupt */
|
#define GIMOD1 GIRQx1 /* */
|
#define GIMOD2 GIRQx2 /* */
|
#define GIMOD3 GIRQx3 /* */
|
#define GIMOD4 GIRQx4 /* */
|
#define GIMOD5 GIRQx5 /* */
|
#define GIMOD6 GIRQx6 /* */
|
#define GIMOD7 GIRQx7 /* */
|
#define GIMOD8 GIRQx8 /* Value 0 = Level, 1 = Edge. */
|
|
/* offset from EXT_SYNC_ID in bytes */
|
#define GPIO_IBES_OFFSET 0x1C /* sub-register 0x1C is the GPIO interrupt Both Edge?selection register */
|
#define GPIO_IBES_LEN (4)
|
#define GPIO_IBES_MASK GPIO_IRQE_MASK /* */
|
#define GIBES0 GIRQx0 /* GPIO IRQ Both Edge?selection for GPIO0 input. Value 0 = GPIO_IMODE register selects the edge. Value 1 = Both edges trigger the interrupt. */
|
#define GIBES1 GIRQx1 /* */
|
#define GIBES2 GIRQx2 /* */
|
#define GIBES3 GIRQx3 /* */
|
#define GIBES4 GIRQx4 /* */
|
#define GIBES5 GIRQx5 /* */
|
#define GIBES6 GIRQx6 /* */
|
#define GIBES7 GIRQx7 /* */
|
#define GIBES8 GIRQx8 /* Value 0 = use GPIO_IMODE, 1 = Both Edges */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_ICLR_OFFSET 0x20 /* sub-register 0x20 is the GPIO interrupt clear register */
|
#define GPIO_ICLR_LEN (4)
|
#define GPIO_ICLR_MASK GPIO_IRQE_MASK /* */
|
#define GICLR0 GIRQx0 /* GPIO IRQ latch clear for GPIO0 input. Write 1 to clear the GPIO0 interrupt latch. Writing 0 has no effect. Reading returns zero */
|
#define GICLR1 GIRQx1 /* */
|
#define GICLR2 GIRQx2 /* */
|
#define GICLR3 GIRQx3 /* */
|
#define GICLR4 GIRQx4 /* */
|
#define GICLR5 GIRQx5 /* */
|
#define GICLR6 GIRQx6 /* */
|
#define GICLR7 GIRQx7 /* */
|
#define GICLR8 GIRQx8 /* Write 1 to clear the interrupt latch */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_IDBE_OFFSET 0x24 /* sub-register 0x24 is the GPIO interrupt de-bounce enable register */
|
#define GPIO_IDBE_LEN (4)
|
#define GPIO_IDBE_MASK GPIO_IRQE_MASK
|
#define GIDBE0 GIRQx0 /* GPIO IRQ de-bounce enable for GPIO0. Value 1 = de-bounce enabled. Value 0 = de-bounce disabled */
|
#define GIDBE1 GIRQx1 /* */
|
#define GIDBE2 GIRQx2 /* */
|
#define GIDBE3 GIRQx3 /* */
|
#define GIDBE4 GIRQx4 /* */
|
#define GIDBE5 GIRQx5 /* */
|
#define GIDBE6 GIRQx6 /* */
|
#define GIDBE7 GIRQx7 /* */
|
#define GIDBE8 GIRQx8 /* Value 1 = de-bounce enabled, 0 = de-bounce disabled */
|
|
/* offset from GPIO_CTRL in bytes */
|
#define GPIO_RAW_OFFSET 0x28 /* sub-register 0x28 allows the raw state of the GPIO pin to be read. */
|
#define GPIO_RAW_LEN (4)
|
#define GPIO_RAW_MASK GPIO_IRQE_MASK
|
#define GRAWP0 GIRQx0 /* This bit reflects the raw state of GPIO0 */
|
#define GRAWP1 GIRQx1 /* */
|
#define GRAWP2 GIRQx2 /* */
|
#define GRAWP3 GIRQx3 /* */
|
#define GRAWP4 GIRQx4 /* */
|
#define GRAWP5 GIRQx5 /* */
|
#define GRAWP6 GIRQx6 /* */
|
#define GRAWP7 GIRQx7 /* */
|
#define GRAWP8 GIRQx8 /* This bit reflects the raw state of GPIO8 */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register DRX_CONF
|
* Digital Receiver configuration block
|
**/
|
#define DRX_CONF_ID 0x27 /* Digital Receiver configuration */
|
#define DRX_CONF_LEN (44)
|
/* offset from DRX_CONF_ID in bytes */
|
#define DRX_TUNE0b_OFFSET (0x02) /* sub-register 0x02 is a 16-bit tuning register. */
|
#define DRX_TUNE0b_LEN (2)
|
#define DRX_TUNE0b_MASK 0xFFFF /* 7.2.40.2 Sub-Register 0x27:02 ?DRX_TUNE0b */
|
|
/* offset from DRX_CONF_ID in bytes */
|
#define DRX_TUNE1a_OFFSET 0x04 /* 7.2.40.3 Sub-Register 0x27:04 ?DRX_TUNE1a */
|
#define DRX_TUNE1a_LEN (2)
|
#define DRX_TUNE1a_MASK 0xFFFF
|
|
/* offset from DRX_CONF_ID in bytes */
|
#define DRX_TUNE1b_OFFSET 0x06 /* 7.2.40.4 Sub-Register 0x27:06 ?DRX_TUNE1b */
|
#define DRX_TUNE1b_LEN (2)
|
#define DRX_TUNE1b_MASK 0xFFFF
|
|
/* offset from DRX_CONF_ID in bytes */
|
#define DRX_TUNE2_OFFSET 0x08 /* 7.2.40.5 Sub-Register 0x27:08 ?DRX_TUNE2 */
|
#define DRX_TUNE2_LEN (4)
|
#define DRX_TUNE2_MASK 0xFFFFFFFFUL
|
|
/* offset from DRX_CONF_ID in bytes */
|
/* WARNING: Please do NOT set DRX_SFDTOC to zero (disabling SFD detection timeout)
|
* since this risks IC malfunction due to prolonged receiver activity in the event of false preamble detection.
|
*/
|
#define DRX_SFDTOC_OFFSET 0x20 /* 7.2.40.7 Sub-Register 0x27:20 ?DRX_SFDTOC */
|
#define DRX_SFDTOC_LEN (2)
|
#define DRX_SFDTOC_MASK 0xFFFF
|
|
/* offset from DRX_CONF_ID in bytes */
|
#define DRX_PRETOC_OFFSET 0x24 /* 7.2.40.9 Sub-Register 0x27:24 ?DRX_PRETOC */
|
#define DRX_PRETOC_LEN (2)
|
#define DRX_PRETOC_MASK 0xFFFF
|
|
/* offset from DRX_CONF_ID in bytes */
|
#define DRX_DRX_TUNE4HOFFSET 0x26 /* 7.2.40.10 Sub-Register 0x27:26 ?DRX_TUNE4H */
|
#define DRX_DRX_TUNE4H_LEN (2)
|
#define DRX_DRX_TUNE4H_MASK 0xFFFF
|
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register RF_CONF
|
* Analog RF Configuration block
|
* Refer to section 7.2.41 Register file: 0x28 ?Analog RF configuration block
|
**/
|
#define RF_CONF_ID 0x28 /* Analog RF Configuration */
|
#define RF_CONF_LEN (58)
|
#define RF_CONF_TXEN_MASK 0x00400000UL /* TX enable */
|
#define RF_CONF_RXEN_MASK 0x00200000UL /* RX enable */
|
#define RF_CONF_TXPOW_MASK 0x001F0000UL /* turn on power all LDOs */
|
#define RF_CONF_PLLEN_MASK 0x0000E000UL /* enable PLLs */
|
#define RF_CONF_TXBLOCKSEN_MASK 0x00001F00UL /* enable TX blocks */
|
#define RF_CONF_TXPLLPOWEN_MASK (RF_CONF_PLLEN_MASK | RF_CONF_TXPOW_MASK)
|
#define RF_CONF_TXALLEN_MASK (RF_CONF_TXEN_MASK | RF_CONF_TXPOW_MASK | RF_CONF_PLLEN_MASK | RF_CONF_TXBLOCKSEN_MASK)
|
/* offset from TX_CAL_ID in bytes */
|
#define RF_RXCTRLH_OFFSET 0x0B /* */
|
/* offset from TX_CAL_ID in bytes */
|
#define RF_TXCTRL_OFFSET 0x0C /* Analog TX Control Register */
|
#define RF_TXCTRL_LEN (4)
|
#define RF_TXCTRL_TXMTUNE_MASK 0x000001E0UL /* Transmit mixer tuning register */
|
#define RF_TXCTRL_TXTXMQ_MASK 0x00000E00UL /* Transmit mixer Q-factor tuning register */
|
#define RF_TXCTRL_CH1 0x00005C40UL /* 32-bit value to program to Sub-Register 0x28:0C ?RF_TXCTRL */
|
#define RF_TXCTRL_CH2 0x00045CA0UL /* 32-bit value to program to Sub-Register 0x28:0C ?RF_TXCTRL */
|
#define RF_TXCTRL_CH3 0x00086CC0UL /* 32-bit value to program to Sub-Register 0x28:0C ?RF_TXCTRL */
|
#define RF_TXCTRL_CH4 0x00045C80UL /* 32-bit value to program to Sub-Register 0x28:0C ?RF_TXCTRL */
|
#define RF_TXCTRL_CH5 0x001E3FE0UL /* 32-bit value to program to Sub-Register 0x28:0C ?RF_TXCTRL */
|
#define RF_TXCTRL_CH7 0x001E7DE0UL /* 32-bit value to program to Sub-Register 0x28:0C ?RF_TXCTRL */
|
|
/* offset from TX_CAL_ID in bytes */
|
#define RF_STATUS_OFFSET 0x2C /* */
|
|
//#define RF_RXCTRLH_ 0x00000000UL /* */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register
|
**/
|
#define REG_29_ID_RESERVED 0x29
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register TX_CAL
|
* Refer to section 7.2.43 Register file: 0x2A ?Transmitter Calibration block
|
**/
|
#define TX_CAL_ID 0x2A /* Transmitter calibration block */
|
#define TX_CAL_LEN (52)
|
/* offset from TX_CAL_ID in bytes */
|
#define TC_SARL_SAR_C (0) /* SAR control */
|
//#define TC_SARL_OFFSET 0x03 /* Transmitter Calibration ?Latest SAR readings. RO */
|
//#define TC_SARL_LEN (2)
|
/*cause bug in register block TX_CAL, we need to read 1 byte in a time*/
|
#define TC_SARL_SAR_LVBAT_OFFSET (3) /* Latest SAR reading for Voltage level */
|
#define TC_SARL_SAR_LTEMP_OFFSET (4) /* Latest SAR reading for Temperature level */
|
/* offset from TX_CAL_ID in bytes */
|
//#define TC_SARW_OFFSET 0x06 /* Transmitter Calibration ?SAR readings at last Wake-Up */
|
//#define TC_SARW_LEN (2)
|
#define TC_SARW_SAR_WTEMP_OFFSET 0x06 /* SAR reading of Temperature level taken at last wakeup event */
|
#define TC_SARW_SAR_WVBAT_OFFSET 0x07 /* SAR reading of Voltage level taken at last wakeup event */
|
/* offset from TX_CAL_ID in bytes */
|
#define TC_PGDELAY_OFFSET 0x0B /* Transmitter Calibration ?Pulse Generator Delay */
|
#define TC_PGDELAY_LEN (1)
|
#define TC_PGDELAY_CH1 0xC9 /* Recommended value for channel 1 */
|
#define TC_PGDELAY_CH2 0xC2 /* Recommended value for channel 2 */
|
#define TC_PGDELAY_CH3 0xC5 /* Recommended value for channel 3 */
|
#define TC_PGDELAY_CH4 0x95 /* Recommended value for channel 4 */
|
#define TC_PGDELAY_CH5 0xC0 /* Recommended value for channel 5 */
|
#define TC_PGDELAY_CH7 0x93 /* Recommended value for channel 7 */
|
/* offset from TX_CAL_ID in bytes */
|
#define TC_PGTEST_OFFSET 0x0C /* Transmitter Calibration ?Pulse Generator Test */
|
#define TC_PGTEST_LEN (1)
|
#define TC_PGTEST_NORMAL 0x00 /* Normal operation */
|
#define TC_PGTEST_CW 0x13 /* Continuous Wave (CW) Test Mode */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register
|
* Refer to section 7.2.44 Register file: 0x2B ?Frequency synthesiser control block
|
**/
|
#define FS_CTRL_ID 0x2B /* Frequency synthesiser control block */
|
#define FS_CTRL_LEN (21)
|
/* offset from FS_CTRL_ID in bytes */
|
#define FS_RES1_OFFSET 0x00 /* reserved area. Please take care not to write to this area as doing so may cause the DW1000 to malfunction. */
|
#define FS_RES1_LEN (7)
|
/* offset from FS_CTRL_ID in bytes */
|
#define FS_PLLCFG_OFFSET 0x07 /* Frequency synthesiser ?PLL configuration */
|
#define FS_PLLCFG_LEN (5)
|
#define FS_PLLCFG_CH1 0x09000407UL /* Operating Channel 1 */
|
#define FS_PLLCFG_CH2 0x08400508UL /* Operating Channel 2 (same as 4) */
|
#define FS_PLLCFG_CH3 0x08401009UL /* Operating Channel 3 */
|
#define FS_PLLCFG_CH4 0x08400508UL /* Operating Channel 4 (same as 2) */
|
#define FS_PLLCFG_CH5 0x0800041DUL /* Operating Channel 5 (same as 7) */
|
#define FS_PLLCFG_CH7 0x0800041DUL /* Operating Channel 7 (same as 5) */
|
/* offset from FS_CTRL_ID in bytes */
|
#define FS_PLLTUNE_OFFSET 0x0B /* Frequency synthesiser ?PLL Tuning */
|
#define FS_PLLTUNE_LEN (1)
|
#define FS_PLLTUNE_CH1 0x1E /* Operating Channel 1 */
|
#define FS_PLLTUNE_CH2 0x26 /* Operating Channel 2 (same as 4) */
|
#define FS_PLLTUNE_CH3 0x5E /* Operating Channel 3 */
|
#define FS_PLLTUNE_CH4 0x26 /* Operating Channel 4 (same as 2) */
|
#define FS_PLLTUNE_CH5 0xA6 /* Operating Channel 5 (same as 7) */
|
#define FS_PLLTUNE_CH7 0xA6 /* Operating Channel 7 (same as 5) */
|
/* offset from FS_CTRL_ID in bytes */
|
#define FS_RES2_OFFSET 0x0C /* reserved area. Please take care not to write to this area as doing so may cause the DW1000 to malfunction. */
|
#define FS_RES2_LEN (2)
|
/* offset from FS_CTRL_ID in bytes */
|
#define FS_XTALT_OFFSET 0x0E /* Frequency synthesiser ?Crystal trim */
|
#define FS_XTALT_LEN (1)
|
#define FS_XTALT_MASK 0x1F /* Crystal Trim. Crystals may be trimmed using this register setting to tune out errors, see 8.1 ?IC Calibration ?Crystal Oscillator Trim. */
|
#define FS_XTALT_MIDRANGE 0x10
|
/* offset from FS_CTRL_ID in bytes */
|
#define FS_RES3_OFFSET 0x0F /* reserved area. Please take care not to write to this area as doing so may cause the DW1000 to malfunction. */
|
#define FS_RES3_LEN (6)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register
|
**/
|
#define AON_ID 0x2C /* Always-On register set */
|
#define AON_LEN (12)
|
/* offset from AON_ID in bytes */
|
#define AON_WCFG_OFFSET 0x00 /* used to control what the DW1000 IC does as it wakes up from low-power SLEEP or DEEPSLEEPstates. */
|
#define AON_WCFG_LEN (2)
|
#define AON_WCFG_MASK 0x09CB /* access mask to AON_WCFG register*/
|
#define AON_WCFG_ONW_RADC 0x0001 /* On Wake-up Run the (temperature and voltage) Analog-to-Digital Convertors */
|
#define AON_WCFG_ONW_RX 0x0002 /* On Wake-up turn on the Receiver */
|
#define AON_WCFG_ONW_LEUI 0x0008 /* On Wake-up load the EUI from OTP memory into Register file: 0x01 ?Extended Unique Identifier. */
|
#define AON_WCFG_ONW_LDC 0x0040 /* On Wake-up load configurations from the AON memory into the host interface register set */
|
#define AON_WCFG_ONW_L64P 0x0080 /* On Wake-up load the Length64 receiver operating parameter set */
|
#define AON_WCFG_PRES_SLEEP 0x0100 /* Preserve Sleep. This bit determines what the DW1000 does with respect to the ARXSLP and ATXSLP sleep controls */
|
#define AON_WCFG_ONW_LLDE 0x0800 /* On Wake-up load the LDE microcode. */
|
#define AON_WCFG_ONW_LLDO 0x1000 /* On Wake-up load the LDO tune value. */
|
/* offset from AON_ID in bytes */
|
#define AON_CTRL_OFFSET 0x02 /* The bits in this register in general cause direct activity within the AON block with respect to the stored AON memory */
|
#define AON_CTRL_LEN (1)
|
#define AON_CTRL_MASK 0x8F /* access mask to AON_CTRL register */
|
#define AON_CTRL_RESTORE 0x01 /* When this bit is set the DW1000 will copy the user configurations from the AON memory to the host interface register set. */
|
#define AON_CTRL_SAVE 0x02 /* When this bit is set the DW1000 will copy the user configurations from the host interface register set into the AON memory */
|
#define AON_CTRL_UPL_CFG 0x04 /* Upload the AON block configurations to the AON */
|
#define AON_CTRL_DCA_READ 0x08 /* Direct AON memory access read */
|
#define AON_CTRL_DCA_ENAB 0x80 /* Direct AON memory access enable bit */
|
/* offset from AON_ID in bytes */
|
#define AON_RDAT_OFFSET 0x03 /* AON Direct Access Read Data Result */
|
#define AON_RDAT_LEN (1)
|
/* offset from AON_ID in bytes */
|
#define AON_ADDR_OFFSET 0x04 /* AON Direct Access Address */
|
#define AON_ADDR_LEN (1)
|
|
/* offset from AON_ID in bytes */
|
#define AON_CFG0_OFFSET 0x06 /* 32-bit configuration register for the always on block. */
|
#define AON_CFG0_LEN (4)
|
#define AON_CFG0_SLEEP_EN 0x00000001UL /* This is the sleep enable configuration bit */
|
#define AON_CFG0_WAKE_PIN 0x00000002UL /* Wake using WAKEUP pin */
|
#define AON_CFG0_WAKE_SPI 0x00000004UL /* Wake using SPI access SPICSn */
|
#define AON_CFG0_WAKE_CNT 0x00000008UL /* Wake when sleep counter elapses */
|
#define AON_CFG0_LPDIV_EN 0x00000010UL /* Low power divider enable configuration */
|
#define AON_CFG0_LPCLKDIVA_MASK 0x0000FFE0UL /* divider count for dividing the raw DW1000 XTAL oscillator frequency to set an LP clock frequency */
|
#define AON_CFG0_LPCLKDIVA_SHIFT (5)
|
#define AON_CFG0_SLEEP_TIM 0xFFFF0000UL /* Sleep time. This field configures the sleep time count elapse value */
|
#define AON_CFG0_SLEEP_SHIFT (16)
|
/* offset from AON_ID in bytes */
|
#define AON_CFG1_OFFSET 0x0A
|
#define AON_CFG1_LEN (2)
|
#define AON_CFG1_MASK 0x0007 /* aceess mask to AON_CFG1 */
|
#define AON_CFG1_SLEEP_CEN 0x0001 /* This bit enables the sleep counter */
|
#define AON_CFG1_SMXX 0x0002 /* This bit needs to be set to 0 for correct operation in the SLEEP state within the DW1000 */
|
#define AON_CFG1_LPOSC_CAL 0x0004 /* This bit enables the calibration function that measures the period of the ICs internal low powered oscillator */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register OTP_IF
|
* Refer to section 7.2.46 Register file: 0x2D ?OTP Memory Interface
|
**/
|
#define OTP_IF_ID 0x2D /* One Time Programmable Memory Interface */
|
#define OTP_IF_LEN (18)
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_WDAT 0x00 /* 32-bit register. The data value to be programmed into an OTP location */
|
#define OTP_WDAT_LEN (4)
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_ADDR 0x04 /* 16-bit register used to select the address within the OTP memory block */
|
#define OTP_ADDR_LEN (2)
|
#define OTP_ADDR_MASK 0x07FF /* This 11-bit field specifies the address within OTP memory that will be accessed read or written. */
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_CTRL 0x06 /* used to control the operation of the OTP memory */
|
#define OTP_CTRL_LEN (2)
|
#define OTP_CTRL_MASK 0x8002
|
#define OTP_CTRL_OTPRDEN 0x0001 /* This bit forces the OTP into manual read mode */
|
#define OTP_CTRL_OTPREAD 0x0002 /* This bit commands a read operation from the address specified in the OTP_ADDR register */
|
#define OTP_CTRL_LDELOAD 0x8000 /* This bit forces a load of LDE microcode */
|
#define OTP_CTRL_OTPPROG 0x0040 /* Setting this bit will cause the contents of OTP_WDAT to be written to OTP_ADDR. */
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_STAT 0x08
|
#define OTP_STAT_LEN (2)
|
#define OTP_STAT_MASK 0x0003
|
#define OTP_STAT_OTPPRGD 0x0001 /* OTP Programming Done */
|
//#define OTP_STAT_OTPVLTOK 0x0002 /* OTP Programming Voltage OK */ !!!!!!!!!!!!
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_RDAT 0x0A /* 32-bit register. The data value read from an OTP location will appear here */
|
#define OTP_RDAT_LEN (4)
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_SRDAT 0x0E /* 32-bit register. The data value stored in the OTP SR (0x400) location will appear here after power up */
|
#define OTP_SRDAT_LEN (4)
|
/* offset from OTP_IF_ID in bytes */
|
#define OTP_SF 0x12 /*8-bit special function register used to select and load special receiver operational parameter */
|
#define OTP_SF_LEN (1)
|
#define OTP_SF_MASK 0x63
|
#define OTP_SF_OPS_KICK 0x01 /* This bit when set initiates a load of the operating parameter set selected by the OPS_SEL */
|
#define OTP_SF_LDO_KICK 0x02 /* This bit when set initiates a load of the LDO tune code */
|
#define OTP_SF_OPS_SEL_L64 0x00 /* Operating parameter set selection: Length64 */
|
#define OTP_SF_OPS_SEL_TIGHT 0x40 /* Operating parameter set selection: Tight */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register LDE_IF
|
* Refer to section 7.2.47 Register file: 0x2E ?Leading Edge Detection Interface
|
* PLEASE NOTE: Other areas within the address space of Register file: 0x2E ?Leading Edge Detection Interface
|
* are reserved. To ensure proper operation of the LDE algorithm (i.e. to avoid loss of performance or a malfunction),
|
* care must be taken not to write to any byte locations other than those defined in the sub-sections below.
|
**/
|
#define LDE_IF_ID 0x2E /* Leading edge detection control block */
|
#define LDE_IF_LEN (0)
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_THRESH_OFFSET 0x0000 /* 16-bit status register reporting the threshold that was used to find the first path */
|
#define LDE_THRESH_LEN (2)
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_CFG1_OFFSET 0x0806 /*8-bit configuration register*/
|
#define LDE_CFG1_LEN (1)
|
#define LDE_CFG1_NSTDEV_MASK 0x1F /* Number of Standard Deviations mask. */
|
#define LDE_CFG1_PMULT_MASK 0xE0 /* Peak Multiplier mask. */
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_PPINDX_OFFSET 0x1000 /* reporting the position within the accumulator that the LDE algorithm has determined to contain the maximum */
|
#define LDE_PPINDX_LEN (2)
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_PPAMPL_OFFSET 0x1002 /* reporting the magnitude of the peak signal seen in the accumulator data memory */
|
#define LDE_PPAMPL_LEN (2)
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_RXANTD_OFFSET 0x1804 /* 16-bit configuration register for setting the receive antenna delay */
|
#define LDE_RXANTD_LEN (2)
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_CFG2_OFFSET 0x1806 /* 16-bit LDE configuration tuning register */
|
#define LDE_CFG2_LEN (2)
|
/* offset from LDE_IF_ID in bytes */
|
#define LDE_REPC_OFFSET 0x2804 /* 16-bit configuration register for setting the replica avoidance coefficient */
|
#define LDE_REPC_LEN (2)
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register DIG_DIAG
|
* Digital Diagnostics interface.
|
* It contains a number of sub-registers that give diagnostics information.
|
**/
|
#define DIG_DIAG_ID 0x2F /* Digital Diagnostics Interface */
|
#define DIG_DIAG_LEN (41)
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_CTRL_OFFSET 0x00 /* Event Counter Control */
|
#define EVC_CTRL_LEN (4)
|
#define EVC_CTRL_MASK 0x00000003UL/* access mask to Register for bits should always be set to zero to avoid any malfunction of the device. */
|
#define EVC_EN 0x00000001UL/* Event Counters Enable bit */
|
#define EVC_CLR 0x00000002UL
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_PHE_OFFSET 0x04 /* PHR Error Event Counter */
|
#define EVC_PHE_LEN (2)
|
#define EVC_PHE_MASK 0x0FFF
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_RSE_OFFSET 0x06 /* Reed Solomon decoder (Frame Sync Loss) Error Event Counter */
|
#define EVC_RSE_LEN (2)
|
#define EVC_RSE_MASK 0x0FFF
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_FCG_OFFSET 0x08 /* The EVC_FCG field is a 12-bit counter of the frames received with good CRC/FCS sequence. */
|
#define EVC_FCG_LEN (2)
|
#define EVC_FCG_MASK 0x0FFF
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_FCE_OFFSET 0x0A /* The EVC_FCE field is a 12-bit counter of the frames received with bad CRC/FCS sequence. */
|
#define EVC_FCE_LEN (2)
|
#define EVC_FCE_MASK 0x0FFF
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_FFR_OFFSET 0x0C /* The EVC_FFR field is a 12-bit counter of the frames rejected by the receive frame filtering function. */
|
#define EVC_FFR_LEN (2)
|
#define EVC_FFR_MASK 0x0FFF
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_OVR_OFFSET 0x0E /* The EVC_OVR field is a 12-bit counter of receive overrun events */
|
#define EVC_OVR_LEN (2)
|
#define EVC_OVR_MASK 0x0FFF
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_STO_OFFSET 0x10 /* The EVC_STO field is a 12-bit counter of SFD Timeout Error events */
|
#define EVC_OVR_LEN (2)
|
#define EVC_OVR_MASK 0x0FFF
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_PTO_OFFSET 0x12 /* The EVC_PTO field is a 12-bit counter of Preamble detection Timeout events */
|
#define EVC_PTO_LEN (2)
|
#define EVC_PTO_MASK 0x0FFF
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_FWTO_OFFSET 0x14 /* The EVC_FWTO field is a 12-bit counter of receive frame wait timeout events */
|
#define EVC_FWTO_LEN (2)
|
#define EVC_FWTO_MASK 0x0FFF
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_TXFS_OFFSET 0x16 /* The EVC_TXFS field is a 12-bit counter of transmit frames sent. This is incremented every time a frame is sent */
|
#define EVC_TXFS_LEN (2)
|
#define EVC_TXFS_MASK 0x0FFF
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_HPW_OFFSET 0x18 /* The EVC_HPW field is a 12-bit counter of Half Period Warnings? */
|
#define EVC_HPW_LEN (2)
|
#define EVC_HPW_MASK 0x0FFF
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_TPW_OFFSET 0x1A /* The EVC_TPW field is a 12-bit counter of Transmitter Power-Up Warnings? */
|
#define EVC_TPW_LEN (2)
|
#define EVC_TPW_MASK 0x0FFF
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define EVC_RES1_OFFSET 0x1C /* Please take care not to write to this register as doing so may cause the DW1000 to malfunction. */
|
|
/* offset from DIG_DIAG_ID in bytes */
|
#define DIAG_TMC_OFFSET 0x24
|
#define DIAG_TMC_LEN (2)
|
#define DIAG_TMC_MASK 0x0010
|
#define DIAG_TMC_TX_PSTM 0x0010 /* This test mode is provided to help support regulatory approvals spectral testing. When the TX_PSTM bit is set it enables a repeating transmission of the data from the TX_BUFFER */
|
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x30-0x35
|
* Please take care not to write to these registers as doing so may cause the DW1000 to malfunction.
|
**/
|
#define REG_30_ID_RESERVED 0x30
|
#define REG_31_ID_RESERVED 0x31
|
#define REG_32_ID_RESERVED 0x32
|
#define REG_33_ID_RESERVED 0x33
|
#define REG_34_ID_RESERVED 0x34
|
#define REG_35_ID_RESERVED 0x35
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register PMSC
|
**/
|
#define PMSC_ID 0x36 /* Power Management System Control Block */
|
#define PMSC_LEN (48)
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_CTRL0_OFFSET 0x00
|
#define PMSC_CTRL0_LEN (4)
|
#define PMSC_CTRL0_MASK 0xF08F847FUL /* access mask to register PMSC_CTRL0 */
|
#define PMSC_CTRL0_SYSCLKS_AUTO 0x00000000UL /* The system clock will run off the 19.2 MHz XTI clock until the PLL is calibrated and locked, then it will switch over the 125 MHz PLL clock */
|
#define PMSC_CTRL0_SYSCLKS_19M 0x00000001UL /* Force system clock to be the 19.2 MHz XTI clock. */
|
#define PMSC_CTRL0_SYSCLKS_125M 0x00000002UL /* Force system clock to the 125 MHz PLL clock. */
|
#define PMSC_CTRL0_RXCLKS_AUTO 0x00000000UL /* The RX clock will be disabled until it is required for an RX operation */
|
#define PMSC_CTRL0_RXCLKS_19M 0x00000004UL /* Force RX clock enable and sourced clock from the 19.2 MHz XTI clock */
|
#define PMSC_CTRL0_RXCLKS_125M 0x00000008UL /* Force RX clock enable and sourced from the 125 MHz PLL clock */
|
#define PMSC_CTRL0_RXCLKS_OFF 0x0000000CUL /* Force RX clock off. */
|
#define PMSC_CTRL0_TXCLKS_AUTO 0x00000000UL /* The TX clock will be disabled until it is required for a TX operation */
|
#define PMSC_CTRL0_TXCLKS_19M 0x00000010UL /* Force TX clock enable and sourced clock from the 19.2 MHz XTI clock */
|
#define PMSC_CTRL0_TXCLKS_125M 0x00000020UL /* Force TX clock enable and sourced from the 125 MHz PLL clock */
|
#define PMSC_CTRL0_TXCLKS_OFF 0x00000030UL /* Force TX clock off */
|
#define PMSC_CTRL0_FACE 0x00000040UL /* Force Accumulator Clock Enable */
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_CTRL1_OFFSET 0x04
|
#define PMSC_CTRL1_LEN (4)
|
#define PMSC_CTRL1_MASK 0xFC02F802UL /* access mask to register PMSC_CTRL1 */
|
#define PMSC_CTRL1_ARX2INIT 0x00000002UL /* Automatic transition from receive mode into the INIT state */
|
#define PMSC_CTRL1_ATXSLP 0x00000800UL /* If this bit is set then the DW1000 will automatically transition into SLEEP or DEEPSLEEP mode after transmission of a frame */
|
#define PMSC_CTRL1_ARXSLP 0x00001000UL /* this bit is set then the DW1000 will automatically transition into SLEEP mode after a receive attempt */
|
#define PMSC_CTRL1_SNOZE 0x00002000UL /* Snooze Enable */
|
#define PMSC_CTRL1_SNOZR 0x00004000UL /* The SNOZR bit is set to allow the snooze timer to repeat twice */
|
#define PMSC_CTRL1_PLLSYN 0x00008000UL /* This enables a special 1 GHz clock used for some external SYNC modes */
|
#define PMSC_CTRL1_LDERUNE 0x00020000UL /* This bit enables the running of the LDE algorithm */
|
#define PMSC_CTRL1_KHZCLKDIV_MASK 0xFC000000UL /* Kilohertz clock divisor */
|
#define PMSC_CTRL1_PKTSEQ_DISABLE 0x00 /* writing this to PMSC CONTROL 1 register (bits 10-3) disables PMSC control of analog RF subsystems */
|
#define PMSC_CTRL1_PKTSEQ_ENABLE 0xE7 /* writing this to PMSC CONTROL 1 register (bits 10-3) enables PMSC control of analog RF subsystems */
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_RES1_OFFSET 0x08
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_SNOZT_OFFSET 0x0C /* PMSC Snooze Time Register */
|
#define PMSC_SNOZT_LEN (1)
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_RES2_OFFSET 0x10
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_RES3_OFFSET 0x24
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_TXFINESEQ_OFFSET 0x26 /* Writing PMSC_TXFINESEQ_DIS_MASK disables fine grain sequencing in the transmitter*/
|
#define PMSC_TXFINESEQ_DIS_MASK (0x0)
|
#define PMSC_TXFINESEQ_EN_MASK (0B74) /* Writing PMSC_TXFINESEQ_EN_MASK enables fine grain sequencing in the transmitter*/
|
/* offset from PMSC_ID in bytes */
|
#define PMSC_LEDC_OFFSET 0x28
|
#define PMSC_LEDC_LEN (4)
|
#define PMSC_LEDC_MASK 0x000001FFUL /* 32-bit LED control register. */
|
#define PMSC_LEDC_BLINK_TIM_MASK 0x000000FFUL /* This field determines how long the LEDs remain lit after an event that causes them to be set on. default 0x20 give 0x20 * 14mS = 400mS */
|
#define PMSC_LEDC_BLNKEN 0x00000100UL /* Blink Enable. When this bit is set to 1 the LED blink feature is enabled. */
|
|
/****************************************************************************//**
|
* @brief Bit definitions for register 0x37-0x3F
|
* Please take care not to write to these registers as doing so may cause the DW1000 to malfunction.
|
**/
|
#define REG_37_ID_RESERVED 0x37
|
#define REG_38_ID_RESERVED 0x38
|
#define REG_39_ID_RESERVED 0x39
|
#define REG_3A_ID_RESERVED 0x3A
|
#define REG_3B_ID_RESERVED 0x3B
|
#define REG_3C_ID_RESERVED 0x3C
|
#define REG_3D_ID_RESERVED 0x3D
|
#define REG_3E_ID_RESERVED 0x3E
|
#define REG_3F_ID_RESERVED 0x3F
|
|
/* END DW1000 REGISTER DEFINITION */
|
|
#ifdef __cplusplus
|
}
|
#endif
|
|
#endif
|
