写完pca555驱动代码未测试

chen

2024-12-03 0ce5b924a576b6aaafced53ba9b44ecd6e0dc09f

 keil/include/main/main.c

@@ -62,7 +62,7 @@
#include "HIDO_Timer.h"
#include "TCPClient.h"

//#define DEBUG_MODE
#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
#define TEST_UART_POLL_MODE 0
@@ -90,13 +90,14 @@
int16_t fVoltage_mv,first_search_flag;
uint8_t bat_percent,g_start_send_flag=1;
uint8_t link_success_flag,motor_count;
uint16_t gps_wait_count;
uint16_t gps_wait_count,gps_wait_count2;
uint8_t state5v = 1;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,chaging_state,changed_state,air780_success_state,first_motor_in_flag;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,red_charge_state,green_charge_state,air780_success_state,first_motor_in_flag;
float nomove_count=0;
static uint32_t sample[NUM_SAMPLES] = {0};
uint8_t recev_error_num,send_messgae_count,send_flag,control_state;
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1;  //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
typedef enum
{      UN_BIND=0,
        LINK_SUCCESS,
@@ -106,7 +107,7 @@


Commend_SendDate send_struct;
static struct ADC_CFG_T usr_adc_cfg = {
struct ADC_CFG_T usr_adc_cfg = {
    .mode = ADC_MODE_CONTINUE,    /* Selected single conversion mode  */
    .clk_sel = ADC_CLK_HIGH,      /* Selected 62.4M high speed clock */
    .vref_sel = ADC_SEL_VREF_INT, /* Using internal reference voltage (1.2V)*/
@@ -146,6 +147,20 @@
{
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
}
void mcu_deep_sleep(void)
{
            uint32_t lock;
            trace_flush();
            lock = int_lock();
                  LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  gps_air780_power_change(0,0);//关闭gps，4G 
                     sleep_timer_stop();	
                  //adc_close();
            power_enter_power_down_mode(1);
                  //LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  sys_reset(0);
            int_unlock(lock);
}
static void adc_callback(void *data, uint32_t number)
{
    uint32_t *result = (uint32_t *)data;
@@ -168,6 +183,17 @@
            bat_percent = ((fVoltage_mv - 3300) /8);
        }
    }
            if(fVoltage_mv<3300)
            {
               power_low_flag=1;
               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
            }else{
               power_low_flag=0;
               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
      gpio_pin_set(ADC_GND_ENABLE);//在拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
//void UartInit(void)
@@ -177,10 +203,12 @@
//board_debug_console_open(TRACE_PORT_UART0);
//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//}
extern gps_uwb_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag;
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2;
extern uint32_t get_in_num,get_out_num;
void MotorPoll(void)
{
    if(UWB_work_state==UN_BIND) {
@@ -190,6 +218,33 @@
    } else { //绑定状态下
        if(anchordata_num==1) {
            if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                fenli_alarm_count = 0;
                if(flag_fenli_alarm)
                {
                    flag_fenli_alarm = 0;
                    fenli_alarm_count = 0;
                    _4GAlarmUpload(2);
                }
            } 
            }
            if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
                     {
                if(fenli_alarm_count++>20)
                {
                           if(!flag_fenli_alarm)
                           {
                    flag_fenli_alarm = 1;
                    _4GAlarmUpload(1);
                           }
                }
                     }
                 if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                if(flag_alam_state)
                {
                    flag_alam_state = 0;

                }		
							
                need_open_gps_count=0;
                moter_open_uwb_flag=0;//关闭震动
                gps_uwb_flag=0;//关闭GPS
@@ -197,6 +252,10 @@
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
@@ -204,20 +263,56 @@
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            
        } 
                  if(anchordata_num==0) {
            if(!flag_alam_state)
            {
                flag_alam_state = 1;
            }
        } else if(anchordata_num==0) {

            distance = 0x1ffff;
            gps_uwb_flag=1;//开启gps测距流程
            moter_open_uwb_flag=1;//开启震动
            need_open_gps_count=0;
        }
    }
}
void MinuteTask(void)
   }
void IMUTask(void)
{
   if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
   {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
      mcu_deep_sleep();
   }
}
void UserKeyTask(void)
 {
     if(!GET_USERKEY)
     {
        if(HIDO_TimerGetTick() - keystarttime>3)
        {
            userkey_state = 1;
            keystarttime =  HIDO_TimerGetTick();
                  UDPClient_UploadGPS();
        }
        if(HIDO_TimerGetTick() - keystarttime2>10)
        {
            g_com_map[CNT_RESTART] = 1;
        }
     }else
     {
       keystarttime =  HIDO_TimerGetTick(); 
       keystarttime2 =  HIDO_TimerGetTick(); 
     }
 } 
void MinuteTask(void)
{      gpio_pin_clr(ADC_GND_ENABLE);//拉低
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
void SecondTask(void)
@@ -227,63 +322,77 @@
        second_count = 0;
        MinuteTask();
    }
    //UWB更新列表
    TagListUpdate();
    GPS_Poll();
    //UWB状态检测
      TagListUpdate_person_num_car();
      in_table_log();
		
//      if(!power_low_flag)
//      Gps_change();
//      else{
//      gps_power_state=0;//关闭GPS
//      update_led_power_state();
//      //初始化GPS计数数据
//      gps_need_data_flag=1;
//      gps_wait_count2=0;
//      gps_wait_count=0;
//      }
//    //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
//   {
//    if(IfTCPConnected())
//    {
//        TCP_reconnect_timer =0;
//        flag_TCP_reconnectting = 0;
//    } else {
//        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
//        {
//            flag_TCP_reconnectting = 1;
//        } else {
//            flag_TCP_reconnectting = 0;
//        }
//        if(TCP_reconnect_timer++>600)
//        {
//            TCP_reconnect_timer = 0;
//        }

    if(IfTCPConnected())
    {
        TCP_reconnect_timer =0;
        flag_TCP_reconnectting = 0;
    } else {
        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
        {
            flag_TCP_reconnectting = 1;
        } else {
            flag_TCP_reconnectting = 0;
        }
        if(TCP_reconnect_timer++>600)
        {
            TCP_reconnect_timer = 0;
        }

    }
//    }
//   }
    HIDO_TimerTick();
      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
    nomove_count++;
      else{
      nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
      }
}
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count;
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
static void sleep_timer_callback(void *dev, uint32_t time)
{
    IO_control_init();
    UWBPoll();
    if(g_com_map[MOTOR_ENABLE])
    MotorPoll();
    if(secondtask_count++%2==0)
    //IO_control_init();
      if(enbale_blink_flag)
   {
   green_charge_state=0;
   charge_red_on();
   }
	 
   charge_state_change();//充电状态判断
if(secondtask_count++%2==0)
    {
        flag_secondtask = 1;
    }else{
        flag_secondtask = 0;
    }

    flag_sleeptimer = 1;

    //马达震动逻辑
    if(motor_open_air_flag||moter_open_uwb_flag)
    {
       if (motor_count++%2==0)
       {
        motor_power_state = 1;
       }else{
        motor_power_state = 0;
       }
    } else {
        motor_power_state=1;
    }

      if(enbale_blink_flag)
   {
      //delay_us(5000);
   green_charge_state=0;
   charge_red_off();
   }		
 if(delaysleep_count>0)
     delaysleep_count--;
    //GPS工作逻辑

}

static void voltage_input_handler(enum IO_PIN_T pin)
{

@@ -293,20 +402,22 @@
    nomove_count=0;
}
uint8_t flag_4G_recdata;
static void _4gUsart_handler(enum IO_PIN_T pin)
void _4gUsart_handler(enum IO_PIN_T pin)
{
    LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
    // flag_4G_recdata = 1;
    // AIR780EUartInit();
     //LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
        flag_4G_recdata = 1;
        delaysleep_count = 3;
}
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
void Program_Init(void)
{
    Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
    parameter_init_anchor();//g_com_map表初始化角色默认为基站
    dev_id=g_com_map[DEV_ID];//这里不太对
    group_id=g_com_map[GROUP_ID];//组ID
    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
//    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
    memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
//    g_com_map[ALARM_DISTANCE1] = 40;
//    g_com_map[ALARM_DISTANCE2] = 40;
@@ -316,57 +427,63 @@
    send_struct.alarmDistence=prewarning_distance;//更新报警距离
    memcpy(&send_struct.gunLableId,&g_com_map[BIND_DEV_ID],2);//更新绑定ID
    send_struct.tagId=dev_id;//更新设备ID
    

    if(g_com_map[BIND_DEV_ID]==0)
    {
        UWB_work_state = UN_BIND;
    }else{
        UWB_work_state = SEARCH_DEV;
    }
    if(g_com_map[SEND_4G_SECOND]<60)
        g_com_map[SEND_4G_SECOND]=60;
      //g_com_map[SEND_4G_SECOND]
    if(g_com_map[SEND_4G_SECOND]<30)
      {
      gps_open_flag=0;
      }else{
      gps_open_flag=1;
      }
    g_com_map[MODBUS_MODE] = 0;
      log_4g_enable_flag=g_com_map[LOG_4G_ENABLE];
    ip0 = (g_com_map[TCP_IP_0]>>12&0xf)*1000+(g_com_map[TCP_IP_0]>>8&0xf)*100+(g_com_map[TCP_IP_0]>>4&0xf)*10+(g_com_map[TCP_IP_0]&0xf);
    ip1 = (g_com_map[TCP_IP_1]>>12&0xf)*1000+(g_com_map[TCP_IP_1]>>8&0xf)*100+(g_com_map[TCP_IP_1]>>4&0xf)*10+(g_com_map[TCP_IP_1]&0xf);
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|2;
    LOG_INFO("设备ID: %x .\r\n",dev_id);
    LOG_INFO("固件版本:UWB-4G手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO("服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
    g_com_map[VERSION] = (1<<8)|0;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}



void IdleTask(void)
{
    if(gpio_pin_get_val(INPUT_5V_Pin))
    {
//    if(gpio_pin_get_val(INPUT_5V_Pin))
//    {

        if(state5v==0)
        {
            state5v=1;
            state5V_prase_flag=state5v;
            gps_prase_flag=0;//解除gps解析
            uart1_change_from_gps_to_debug();
         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartInit();
        }
//        if(state5v==0)
//        {
//            state5v=1;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=0;//解除gps解析
//            uart1_change_from_gps_to_debug();//测试
//         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartInit();
//        }

        //UART_CheckSend();
    } else {
        if(state5v==1)
        {
            g_com_map[MODBUS_MODE] = 0;
            state5v=0;
            state5V_prase_flag=state5v;
            gps_prase_flag=1;//恢复gps解析
            uart1_change_from_debug_to_gps();
          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartDeinit();
        }
    }
//        //UART_CheckSend();
//    } else {
//        if(state5v==1)
//        {
//            g_com_map[MODBUS_MODE] = 0;
//            state5v=0;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=1;//恢复gps解析
//            uart1_change_from_debug_to_gps();//测试
//          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartDeinit();
//        }
//    }
      UART_CheckReceive();
}
int bind_check(void)
@@ -403,12 +520,18 @@
    uart_close(UART_ID0);//解绑原来串口0
}
uint8_t flag_4guart_needinit=0;
uint8_t index1,index2,index3;
int16_t Voltage_input;
int tt2;
int test1,test3;
uint32_t test4;

int main(void)
{
    board_clock_run();
    boot_deinit();
    board_pins_config();
    board_debug_console_open(TRACE_PORT_UART1);
   board_debug_console_open(TRACE_PORT_UART1);
    // Reset reason
    reset_cause_get();
    reset_cause_clear();
@@ -439,89 +562,125 @@

    // TODO 4G
    Uart_Register(UART_ID_4G, UART_ID0);
    Internet_Init();
    TCPClient_Init();
//    Internet_Init();
//    TCPClient_Init();

    gpio_open();
    //board_led_init();

      board_output_init();//配置adcGND引脚
//      battery_monitor_open();
//      Voltage_input=battery_monitor_get();
//      battery_monitor_close();
    adc_open(&usr_adc_cfg);
    IIC2_Init();
    Accelerometer_Init();
    IO_control_init();
    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_OUT, 0);
    io_pull_set(SCL_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
    gps_air780_power_change(0,1);//开启gps，4G 
		
//    IIC2_Init();
//    Accelerometer_Init();
      PCA9555_init();
    //IO_control_init();
//    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
//    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
//    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
    //gps_air780_power_change(0,1);//开启gps，4G 
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
   // uart_open(UART_ID1, &test_uart_cfg);
    Program_Init();
      gpio_pin_clr(ADC_GND_ENABLE);
   
         Program_Init();
    //uart_open(UART_ID1, &test_uart_cfg);
 
   // uart1_change_from_gps_to_debug();   
    //Uart1GpsRecDebugSend();   
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
   
// Initialize low power mode
    power_init();
      //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
    sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    //sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
 //   board_5V_input_init(voltage_input_handler);
       adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    board_acceleration_detection_init(move_handler);
//       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
    AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
      board_4GUsart_detection_init(_4gUsart_handler);
    while (1)
    {
        if(flag_TCP_reconnectting||IfTCPConnected())
        {
            
        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
            air780_led_on();
            if(flag_4guart_needinit)
            {
                flag_4guart_needinit = 0;
                AIR780EUartInit();
            }
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();
            air780_led_off();
        }
    { test4=gpio_pin_get_val(SCL_PIN);
         //UWBPoll();
//         if(!power_low_flag)//确认是否休眠下才开启功能
//         {
//        if(flag_TCP_reconnectting||IfTCPConnected())
//        {
//        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
//           
////            if(flag_4guart_needinit)
////            {
////                flag_4guart_needinit = 0;
////                AIR780EUartInit();
////            }//yuan
//                 if(flag_4G_recdata==1)
//            {
//                flag_4G_recdata = 2;
//               
//                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
//                Socket_RecvAll();
//            }
////                  air780_led_on();
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
////            air780_led_off();
//        }
//      }
        if(flag_secondtask)
        {
            flag_secondtask = 0;
            SecondTask();
					
        }
//            UserKeyTask();
//            IMUTask();
        IdleTask();
        //3种情况后都要发包和休眠
        //if(send_flag){
        //message_construct();
        //send_udp;
        //air780_success_state=0;//关闭4G成功发送灯
        //blink_led(&air780_success_state);//成功测距闪烁4G状态灯
        //air780_success_state=0;
        //}
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
    //    if(!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())&&!flag_4G_recdata) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
        {
            //     if(!flag_4guart_needinit)
            {
                //           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
                //             board_4GUsart_detection_init(_4gUsart_handler);
//
            }
//        if(!gps_need_data_flag&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
//        {
//                 if(!flag_4guart_needinit)
//            {
//                           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
//                             board_4GUsart_detection_init(_4gUsart_handler);

//            }
//               flag_sleeptimer =0;
//            LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
            //    flag_4guart_needinit = 1;
//
            //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
//                flag_4guart_needinit = 1;

//        trace_flush();
//        uint32_t lock = int_lock();
//        //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
//        power_enter_power_down_mode(0);
//        int_unlock(lock);
//        }//yuan

            if(delaysleep_count==0)
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
        {
//               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
            uint32_t lock;
            //flag_4guart_needinit = 1;
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
            
           // delay_us(300000);
            trace_flush();
            lock = int_lock();            
            power_enter_power_down_mode(0);
                  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//               test3=gpio_pin_get_val(_4G_USART_RX_Pin);
               //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
            int_unlock(lock);
        }

#endif
    }
}