GPS手环V1.13，修改蓝灯闪灯逻辑

chen

2025-04-09 1a2264ab2e625c29f8f9454fd6238ae8598124bb

 keil/include/main/main.c

@@ -90,12 +90,12 @@
int16_t fVoltage_mv,first_search_flag;
uint8_t bat_percent,g_start_send_flag=1;
uint8_t link_success_flag,motor_count;
uint16_t gps_wait_count;
uint16_t gps_wait_count,gps_wait_count2;
uint8_t state5v = 1;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,red_charge_state,green_charge_state,air780_success_state,first_motor_in_flag;
float nomove_count=0;
static uint32_t sample[NUM_SAMPLES] = {0};
uint8_t recev_error_num,send_messgae_count,send_flag,control_state;
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1;  //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
typedef enum
@@ -147,6 +147,20 @@
{
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
}
void mcu_deep_sleep(void)
{
            uint32_t lock;
            trace_flush();
            lock = int_lock();
                  LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  gps_air780_power_change(0,0);//关闭gps，4G 
                     sleep_timer_stop();	
                  //adc_close();
            power_enter_power_down_mode(1);
                  //LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  sys_reset(0);
            int_unlock(lock);
}
static void adc_callback(void *data, uint32_t number)
{
    uint32_t *result = (uint32_t *)data;
@@ -169,6 +183,16 @@
            bat_percent = ((fVoltage_mv - 3300) /8);
        }
    }
            if(fVoltage_mv<3300)
            {
               power_low_flag=1;
               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
            }else{
               power_low_flag=0;
               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
      gpio_pin_set(ADC_GND_ENABLE);//在拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
@@ -179,94 +203,32 @@
//board_debug_console_open(TRACE_PORT_UART0);
//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//}
extern uint8_t gps_uwb_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state,deep_sleep_flag;
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2;
extern int16_t beepontime;
extern uint8_t beep_start_flag;
void MotorPoll(void)
{
    if(UWB_work_state==UN_BIND) {
        gps_uwb_flag=0;//关闭GPS
        moter_open_uwb_flag=0;//关闭震动
        need_open_gps_count=0;//清0计数gps
    } else { //绑定状态下
        if(anchordata_num==1) {
            if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                fenli_alarm_count = 0;
                if(flag_fenli_alarm)
                {
                    flag_fenli_alarm = 0;
                    fenli_alarm_count = 0;
                    _4GAlarmUpload(2);
                }
            } 
            }
            if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
                     {
                if(fenli_alarm_count++>20)
                {
                           if(!flag_fenli_alarm)
                           {
                    flag_fenli_alarm = 1;
                    _4GAlarmUpload(1);
                           }
                }
                     }
                 if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                if(flag_alam_state)
                {
                    flag_alam_state = 0;

                }		
							
                need_open_gps_count=0;
                moter_open_uwb_flag=0;//关闭震动
                gps_uwb_flag=0;//关闭GPS
            } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            
        } 
                  if(anchordata_num==0) {
            if(!flag_alam_state)
            {
                flag_alam_state = 1;
            }
            distance = 0x1ffff;
            gps_uwb_flag=1;//开启gps测距流程
            moter_open_uwb_flag=1;//开启震动
            need_open_gps_count=0;
        }
    }
   if(beep_start_flag)
   {
      if(beepontime-->0)
      {
      motor_power_state=0;
      }else{
      beep_start_flag=0;
      motor_power_state=1;
      }
   }
}
void IMUTask(void)
{
if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
    { 
       deep_sleep_flag=1;
    }else{
          deep_sleep_flag=0;
      }
   if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
   {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
      mcu_deep_sleep();
   }
}
void UserKeyTask(void)
 {
@@ -292,6 +254,7 @@
{      gpio_pin_clr(ADC_GND_ENABLE);//拉低
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
uint8_t link_error_time;
void SecondTask(void)
{static uint8_t second_count;
    if(second_count++>60)
@@ -299,14 +262,24 @@
        second_count = 0;
        MinuteTask();
    }
    //UWB更新列表
    TagListUpdate();
      Gps_change();
    //GPS_Poll();
      if(!power_low_flag)
      {Gps_change();
      MotorPoll();
      }else{
      gps_power_state=0;//关闭GPS
      update_led_power_state();
      //初始化GPS计数数据
      gps_need_data_flag=1;
      gps_wait_count2=0;
      gps_wait_count=0;
      }
		
    //UWB状态检测

if(!power_low_flag)//低供电下不需要检测重连
   {
    if(IfTCPConnected())
    {
            link_error_time=0;
        TCP_reconnect_timer =0;
        flag_TCP_reconnectting = 0;
    } else {
@@ -314,7 +287,8 @@
        {
            flag_TCP_reconnectting = 1;
        } else {
            flag_TCP_reconnectting = 0;
               //flag_TCP_reconnectting = 0;
            sys_reset(4);//重连不上就复位
        }
        if(TCP_reconnect_timer++>600)
        {
@@ -322,15 +296,20 @@
        }

    }
   }
    HIDO_TimerTick();
      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
    nomove_count++;
      else{
      nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
      }
}
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
static void sleep_timer_callback(void *dev, uint32_t time)
{
   // IO_control_init();
    IO_control_init();
      if(enbale_blink_flag)
   {
   green_charge_state=0;
@@ -345,6 +324,7 @@
    }
      if(enbale_blink_flag)
   {
      delay_us(5000);
   green_charge_state=0;
   charge_red_off();
   }      
@@ -371,6 +351,7 @@
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
uint8_t bat_bercent_hex; 
void Program_Init(void)
{
    Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
@@ -394,6 +375,7 @@
    }else{
        UWB_work_state = SEARCH_DEV;
    }
      //g_com_map[SEND_4G_SECOND]
    if(g_com_map[SEND_4G_SECOND]<30)
      {
      gps_open_flag=0;
@@ -407,9 +389,9 @@
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|10;
    g_com_map[VERSION] = (1<<8)|13;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-4G车载手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}

@@ -480,11 +462,23 @@
}
uint8_t flag_4guart_needinit=0;
uint8_t index1,index2,index3;

int16_t Voltage_input;
int tt2;
int test1,test3;
uint32_t test4;
uint32_t time_count;

static void app_wdt_callback(void *dev, uint32_t status)
{
    ASSERT(status, "WDT TIMEOUT，程序复位");
      //LOG_INFO(TRACE_MODULE_APP, "程序卡死，看门狗复位");
}
 struct WDT_CFG_T app_wdt_cfg = {
        .timeout = 32768 * 30,
        .rst_en = true,
        .int_en = true,
        .callback = app_wdt_callback,
    };
int main(void)
{
    board_clock_run();
@@ -514,6 +508,7 @@

    // Disable watchdog timer
    wdt_close(WDT_ID0);
      wdt_open(WDT_ID0,&app_wdt_cfg);//30s检测喂狗
    LOG_INFO(TRACE_MODULE_APP, "UWB simple example\r\n");

    // open system timer
@@ -526,6 +521,9 @@

    gpio_open();
      board_output_init();//配置adcGND引脚
//      battery_monitor_open();
//      Voltage_input=battery_monitor_get();
//      battery_monitor_close();
    adc_open(&usr_adc_cfg);
      
    IIC2_Init();
@@ -534,10 +532,10 @@
    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
    gps_air780_power_change(0,1);//开启gps，4G 
    //gps_air780_power_change(0,1);//开启gps，4G 
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
      gpio_pin_clr(ADC_GND_ENABLE);
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
   
         Program_Init();
    //uart_open(UART_ID1, &test_uart_cfg);
 
@@ -547,21 +545,28 @@
   
// Initialize low power mode
    power_init();
      AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
      //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
 //   board_5V_input_init(voltage_input_handler);
		
       adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    board_acceleration_detection_init(move_handler);
//       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
      board_4GUsart_detection_init(_4gUsart_handler);
		
    while (1)
    { test4=gpio_pin_get_val(SCL_PIN);
//         if(!deep_sleep_flag)//确认是否休眠下才开启功能
//         {
    { 
         test4=gpio_pin_get_val(SCL_PIN);
         wdt_ping(WDT_ID0);//喂狗
         if(!power_low_flag)//确认是否休眠下才开启功能
         {
        if(flag_TCP_reconnectting||IfTCPConnected())
        {
//               if(flag_TCP_reconnectting)
//               {
//               link_error_time++;
//               }//后加的
        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
           
//            if(flag_4guart_needinit)
@@ -583,12 +588,12 @@
            TCPClient_Poll();
//            air780_led_off();
        }
//      }
      }
        if(flag_secondtask)
        {
            flag_secondtask = 0;
            SecondTask();
					
            //   time_count++;
        }
            UserKeyTask();
            IMUTask();
@@ -615,16 +620,15 @@
//        }//yuan

            if(delaysleep_count==0)
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected()))) 
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
        {
//               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
            uint32_t lock;
            //flag_4guart_needinit = 1;
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();
         //   power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)_4G_USART_RX_Pin, POWER_WAKEUP_LEVEL_LOW);
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
            
           // delay_us(300000);
            trace_flush();