这个版本专门测试周围基站数量的 通过串口打印 波特率921600 如果要升级读取等功能用上个版本

WXK

2 天以前 2ea6286cc6eeb393d57ace3022634a9e86e7e01d

 keil/include/main/main.c

@@ -61,10 +61,16 @@
#include "HIDO_ATLite.h"
#include "HIDO_Timer.h"
#include "TCPClient.h"
#include "PCA9555.h"
#include "WS2812.h"
#include "dw_app_anchor.h"
#include "ymodem.h"
#include "mk_phy.h"

//#define DEBUG_MODE
#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
void uart_change_check(uint16_t gpio_state);
#define TEST_UART_POLL_MODE 0
#define TEST_UART_INTERUPT_MODE 1
#define TEST_UART_DMA_MODE 2
@@ -90,23 +96,24 @@
int16_t fVoltage_mv,first_search_flag;
uint8_t bat_percent,g_start_send_flag=1;
uint8_t link_success_flag,motor_count;
uint16_t gps_wait_count;
uint8_t state5v;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,chaging_state,changed_state,air780_success_state,first_motor_in_flag;
uint16_t gps_wait_count,gps_wait_count2;
uint8_t state5v = 1;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,red_charge_state,green_charge_state,air780_success_state,first_motor_in_flag;
float nomove_count=0;
static uint32_t sample[NUM_SAMPLES] = {0};
uint8_t recev_error_num,send_messgae_count,send_flag,control_state;
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1;  //4G 串口RX当前是 RX状态，不是GPIO状态
typedef enum
{      UN_BIND=0,
        LINK_SUCCESS,
        SEARCH_DEV,
} Operation_step;
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
extern uint8_t pca9555writedata_config[10];//暂存寄存器所有配置的数组
extern uint8_t pca9555writedata_output[10];//暂存输出高低电平配置的数组
extern uint8_t pca9555writedata_input[10];//暂存输入寄存器所有配置的数组
extern uint8_t pca9555writedata_polarity[10];//暂存输入极性反转寄存器所有配置的数组
uint8_t temp_pca9555writedata_input[10];//暂存上一次输入寄存器所有配置的数组
Operation_step UWB_work_state;


Commend_SendDate send_struct;
static struct ADC_CFG_T usr_adc_cfg = {
struct ADC_CFG_T usr_adc_cfg = {
    .mode = ADC_MODE_CONTINUE,    /* Selected single conversion mode  */
    .clk_sel = ADC_CLK_HIGH,      /* Selected 62.4M high speed clock */
    .vref_sel = ADC_SEL_VREF_INT, /* Using internal reference voltage (1.2V)*/
@@ -127,7 +134,7 @@
    .flow = UART_FLOW_CONTROL_NONE,
    .rx_level = UART_RXFIFO_CHAR_1,
    .tx_level = UART_TXFIFO_EMPTY,
    .baud = BAUD_115200,
    .baud = BAUD_9600,
#if (TEST_UART_MODE == TEST_UART_POLL_MODE)
    .dma_en = false,
    .int_rx = false,
@@ -142,9 +149,23 @@
    .int_tx = false,
#endif
};
static void uart_receive_callback(void *dev, uint32_t err_code)
void uart_receive_callback(void *dev, uint32_t err_code)
{
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
}
void mcu_deep_sleep(void)
{
            uint32_t lock;
            trace_flush();
            lock = int_lock();
                  LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  gps_air780_power_change(0,0);//关闭gps，4G 
                     sleep_timer_stop();	
                  //adc_close();
            power_enter_power_down_mode(1);
                  //LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  sys_reset(0);
            int_unlock(lock);
}
static void adc_callback(void *data, uint32_t number)
{
@@ -168,7 +189,18 @@
            bat_percent = ((fVoltage_mv - 3300) /8);
        }
    }
    LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
            if(fVoltage_mv<3300)
            {
               power_low_flag=1;
               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               //LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
            }else{
               power_low_flag=0;
               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               //LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
      PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
//void UartInit(void)
//{
@@ -177,175 +209,358 @@
//board_debug_console_open(TRACE_PORT_UART0);
//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//}
extern gps_uwb_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag;
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
void MotorPoll(void)
{
    if(UWB_work_state==UN_BIND) {
        gps_uwb_flag=0;//关闭GPS
        moter_open_uwb_flag=0;//关闭震动
        need_open_gps_count=0;//清0计数gps
    } else { //绑定状态下
        if(anchordata_num==1) {
            if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                need_open_gps_count=0;
                moter_open_uwb_flag=0;//关闭震动
                gps_uwb_flag=0;//关闭GPS
            } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            }
        } else if(anchordata_num==0) {
uint32_t keystarttime,keystarttime2,keystarttime3;
extern uint32_t get_in_num,get_out_num;
//void MotorPoll(void)
//{
//    if(UWB_work_state==UN_BIND) {
//        gps_uwb_flag=0;//关闭GPS
//        moter_open_uwb_flag=0;//关闭震动
//        need_open_gps_count=0;//清0计数gps
//    } else { //绑定状态下
//        if(anchordata_num==1) {
//            if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
//                fenli_alarm_count = 0;
//                if(flag_fenli_alarm)
//                {
//                    flag_fenli_alarm = 0;
//                    fenli_alarm_count = 0;
//                    _4GAlarmUpload(2);
//                }
//            } 
//            }
//            if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
//                     {
//                if(fenli_alarm_count++>20)
//                {
//                           if(!flag_fenli_alarm)
//                           {
//                    flag_fenli_alarm = 1;
//                    _4GAlarmUpload(1);
//                           }
//                }
//                     }
//                 if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
//                if(flag_alam_state)
//                {
//                    flag_alam_state = 0;

            gps_uwb_flag=1;//开启gps测距流程
            moter_open_uwb_flag=1;//开启震动
            need_open_gps_count=0;
//                }		
//							
//                need_open_gps_count=0;
//                moter_open_uwb_flag=0;//关闭震动
//                gps_uwb_flag=0;//关闭GPS
//            } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
//                need_open_gps_count++;
//                moter_open_uwb_flag=1;//开启震动
//                if(need_open_gps_count>=20) {
//                    if(!flag_alam_state)
//                    {
//                        flag_alam_state = 1;
//                    }
//                    gps_uwb_flag=1;//开启gps测距流程
//                    need_open_gps_count=0;
//                }
//            } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
//                need_open_gps_count++;
//                moter_open_uwb_flag=1;//开启震动
//                if(need_open_gps_count>=20) {
//                    if(!flag_alam_state)
//                    {
//                        flag_alam_state = 1;
//                    }
//                    gps_uwb_flag=1;//开启gps测距流程
//                    need_open_gps_count=0;
//                }
//            
//        } 
//                  if(anchordata_num==0) {
//            if(!flag_alam_state)
//            {
//                flag_alam_state = 1;
//            }
//            distance = 0x1ffff;
//            gps_uwb_flag=1;//开启gps测距流程
//            moter_open_uwb_flag=1;//开启震动
//            need_open_gps_count=0;
//        }
//    }
//   }
void IMUTask(void)
{
   if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
   {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
      mcu_deep_sleep();
   }
}
void UserKeyTask(void)
{
if(!read_userkey_input_pca())
     {
        if(HIDO_TimerGetTick() - keystarttime3>2)
        {
            userkey_state = 1;
            keystarttime3 =  HIDO_TimerGetTick();
                  //UDPClient_UploadGPS();
        }
    }
//        if(HIDO_TimerGetTick() - keystarttime2>10)
//        {
//						
//            g_com_map[CNT_RESTART] = 1;
//        }
     }else
     {
       keystarttime3 =  HIDO_TimerGetTick(); 
     }
} 
void PowerTask(void)
{
     if(read_powerkey_input_pca())
     {
        if(HIDO_TimerGetTick() - keystarttime>2)
        {
            keystarttime =  HIDO_TimerGetTick();
                  PCA9555_Set_One_Value_Output(PWR_ENABLE,0);//低电平关闭
                  PCA9555_Set_One_Value_Output(GPS_LED,0);//输出低电平关闭LED
        }
//        if(HIDO_TimerGetTick() - keystarttime2>10)
//        {
//						
//            g_com_map[CNT_RESTART] = 1;
//        }
     }else
     {
       keystarttime =  HIDO_TimerGetTick(); 
       keystarttime2 =  HIDO_TimerGetTick(); 
     }
}
void MinuteTask(void)
{		
      PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
void SecondTask(void)
{
    //UWB更新列表
    TagListUpdate();
    GPS_Poll();
    g_com_map[ALARM_DISTANCE1]=30;//测试
    g_com_map[ALARM_DISTANCE2]=40;
    //UWB状态检测

    if(IfTCPConnected())
{static uint8_t second_count;
    if(second_count++>60)
    {
        TCP_reconnect_timer =0;
        flag_TCP_reconnectting = 0;
    } else {
        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
        {
            flag_TCP_reconnectting = 1;
        } else {
            flag_TCP_reconnectting = 0;
        }
        if(TCP_reconnect_timer++>600)
        {
            TCP_reconnect_timer = 0;
        }

        second_count = 0;
        MinuteTask();
    }
		
//      if(!power_low_flag)
//      Gps_change();
//      else{
//      gps_power_state=0;//关闭GPS
//      update_led_power_state();
//      //初始化GPS计数数据
//      gps_need_data_flag=1;
//      gps_wait_count2=0;
//      gps_wait_count=0;
//      }
//    //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
//   {
//    if(IfTCPConnected())
//    {
//        TCP_reconnect_timer =0;
//        flag_TCP_reconnectting = 0;
//    } else {
//        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
//        {
//            flag_TCP_reconnectting = 1;
//        } else {
//            flag_TCP_reconnectting = 0;
//        }
//        if(TCP_reconnect_timer++>600)
//        {
//            TCP_reconnect_timer = 0;
//        }

//    }
//   }
    HIDO_TimerTick();
      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
    nomove_count++;
      else{
      nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
      }
}
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count;
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;

void PwtagTimeTask(void)
{
    for(uint8_t i=0; i<PWTAG_MAXGROUPNUM; i++)
    {
        if(pwtag.remain_time[i]>0)
        {
            pwtag.remain_time[i]--;
        }
    }
}
void check_input_change(void)
{
   uint16_t gpio_state;
   gpio_state=(uint16_t)pca9555writedata_input[0]<<8|pca9555writedata_input[1];
   if(WAKE_UP_POSITION&gpio_state)
   {
      nomove_count=0;
   }
   //uart_change_check(gpio_state);
}
uint8_t Get_anchor_appdata_flag;
uint8_t Get_anchor_appdata_num;
extern uint8_t update_tag_time;
static void sleep_timer_callback(void *dev, uint32_t time)
{
    IO_control_init();
    UWBPoll();
 //   MotorPoll();
    if(secondtask_count++%2==0)
    {
if(secondtask_count++%2==0)
    {   
        flag_secondtask = 1;
        PwtagTimeTask();
        if(update_tag_time>0)
        {
            update_tag_time--;
            if(update_tag_time==0)
            {
            NVIC_SystemReset();
            }
        }
        if(Get_anchor_appdata_flag==1)
        {
        Get_anchor_appdata_num++;
            if(Get_anchor_appdata_num>40)
            {
            g_com_map[YAOGEIANC_UPWENJIAN_FLAG]=0;
            save_com_map_to_flash();  
            delay_ms(300);                        
                NVIC_SystemReset();
            }
        }
    }else{
        flag_secondtask = 0;
    }

    flag_sleeptimer = 1;

    //马达震动逻辑
    if(motor_open_air_flag||moter_open_uwb_flag)
    {
       if (motor_count++%2==0)
       {
        motor_power_state = 1;
       }else{
        motor_power_state = 0;
       }
    } else {
        motor_power_state=1;
    }

 if(delaysleep_count>0)
     delaysleep_count--;
    //GPS工作逻辑

}
static void voltage_input_handler(enum IO_PIN_T pin)
{

}
static void move_handler(enum IO_PIN_T pin)
{
    nomove_count=0;
}
uint8_t flag_4G_recdata;
static void _4gUsart_handler(enum IO_PIN_T pin)
static void pca_handler(enum IO_PIN_T pin)
{
    LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
    // flag_4G_recdata = 1;
    // AIR780EUartInit();
   PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
   check_input_change();
}
uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
{
     //LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
        flag_4G_recdata = 1;
        delaysleep_count = 3;
}
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
uint8_t uwb_ch;
void Program_Init(void)
{
    Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
    parameter_init_anchor();//g_com_map表初始化角色默认为基站
    dev_id=g_com_map[DEV_ID];//这里不太对
    group_id=g_com_map[GROUP_ID];//组ID
    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
//    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
    memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
    g_com_map[ALARM_DISTANCE1] = 40;
    g_com_map[ALARM_DISTANCE2] = 40;
//    g_com_map[ALARM_DISTANCE1] = 40;
//    g_com_map[ALARM_DISTANCE2] = 40;
    warning_distance=g_com_map[ALARM_DISTANCE1];
    prewarning_distance=g_com_map[ALARM_DISTANCE2];
    send_struct.warnDistence=warning_distance;
    send_struct.alarmDistence=prewarning_distance;//更新报警距离
    memcpy(&send_struct.gunLableId,&g_com_map[BIND_DEV_ID],2);//更新绑定ID
    send_struct.tagId=dev_id;//更新设备ID
    g_com_map[BIND_DEV_ID] = 0x1234;
    if(g_com_map[BIND_DEV_ID]==0)
    {
        UWB_work_state = UN_BIND;
    }else{
        UWB_work_state = SEARCH_DEV;
    }
//    uwb_ch=g_com_map[NEARBASE_ID1];
//    if(g_com_map[BIND_DEV_ID]==0)
//    {
//        UWB_work_state = UN_BIND;
//    }else{
//        UWB_work_state = SEARCH_DEV;
//    }
      //g_com_map[SEND_4G_SECOND]
    if(g_com_map[SEND_4G_SECOND]<30)
      {
      gps_open_flag=0;
      }else{
      gps_open_flag=1;
      }
    g_com_map[MODBUS_MODE] = 0;
      log_4g_enable_flag=g_com_map[LOG_4G_ENABLE];
    ip0 = (g_com_map[TCP_IP_0]>>12&0xf)*1000+(g_com_map[TCP_IP_0]>>8&0xf)*100+(g_com_map[TCP_IP_0]>>4&0xf)*10+(g_com_map[TCP_IP_0]&0xf);
    ip1 = (g_com_map[TCP_IP_1]>>12&0xf)*1000+(g_com_map[TCP_IP_1]>>8&0xf)*100+(g_com_map[TCP_IP_1]>>4&0xf)*10+(g_com_map[TCP_IP_1]&0xf);
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|0;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}



void IdleTask(void)
void uart_change_check(uint16_t gpio_state)
{
    if(gpio_pin_get_val(INPUT_5V_Pin))
    {

        if(state5v==0)
   if(INPUT_5V_POSITION&gpio_state)
      {
              if(state5v==0)
        {
            state5v=1;
            state5V_prase_flag=state5v;
            gps_prase_flag=0;//解除gps解析
            uart1_change_from_gps_to_debug();
            uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartInit();
        }

        //UART_CheckSend();
    } else {
            uart1_change_from_gps_to_debug();//测试
                  PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
        } 
      }else {
        if(state5v==1)
        {
            g_com_map[MODBUS_MODE] = 0;
            state5v=0;
            state5V_prase_flag=state5v;
            gps_prase_flag=1;//恢复gps解析
            uart1_change_from_debug_to_gps();
            uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartDeinit();
            uart1_change_from_debug_to_gps();//测试
                  PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
        }
    }
      UART_CheckReceive();
         }
}
void IdleTask(void)
{
//if(read_5v_input_pca())
//      {
//              if(state5v==0)
//        {
////            state5v=1;
////            state5V_prase_flag=state5v;
////            gps_prase_flag=0;//解除gps解析
////            uart1_change_from_gps_to_debug();//测试
////                  PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
//        } 
//      }else {
//        if(state5v==1)
//        {
////            g_com_map[MODBUS_MODE] = 0;
////            state5v=0;
////            state5V_prase_flag=state5v;
////            gps_prase_flag=1;//恢复gps解析
////            uart1_change_from_debug_to_gps();//测试
////                  PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
//        }
//         }
      UART0_CheckReceive();
}
int bind_check(void)
{
@@ -358,16 +573,16 @@
//绑定信息为0说明设备未被绑定
    }
}
void check_if_in_search(void)
{
    if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
        UWB_work_state=LINK_SUCCESS;
    } else { //否则进入搜索模式
        UWB_work_state=SEARCH_DEV;
        if(first_search_flag==0)
            first_search_flag=1;
    }
}
//void check_if_in_search(void)
//{
//    if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
//        UWB_work_state=LINK_SUCCESS;
//    } else { //否则进入搜索模式
//        UWB_work_state=SEARCH_DEV;
//        if(first_search_flag==0)
//            first_search_flag=1;
//    }
//}
void boot_deinit(void)
{
   //将boot中串口返回普通gpio
@@ -381,16 +596,120 @@
    uart_close(UART_ID0);//解绑原来串口0
}
uint8_t flag_4guart_needinit=0;
uint8_t index1,index2,index3;
int16_t Voltage_input;
int tt2;
int test1,test3;
uint32_t test4;
void Chuanshuwenjian_Poll()
{
    if(g_com_map[YAOGEIANC_UPWENJIAN_FLAG]==1)
    {
        calib_chip();
        wdt_close(WDT_ID0);
        Get_anchor_appdata_flag=1;
        struct UART_CFG_T test_uart_cfg =
        {
        .parity = UART_PARITY_NONE,
        .stop = UART_STOP_BITS_1,
        .data = UART_DATA_BITS_8,
        .flow = UART_FLOW_CONTROL_NONE,
        .rx_level = UART_RXFIFO_CHAR_1,
        .tx_level = UART_TXFIFO_EMPTY,
        .baud = BAUD_115200,
        .dma_en = true,
        .int_rx = false,
        .int_tx = false,

      };
       flash_open(FLASH_ID0, NULL);
       //uart_open(UART_ID1, &test_uart_cfg);
        uart_open(UART_ID0, &test_uart_cfg);
       //uart_receive(UART_ID1, trx_buf, 1, uart_receive_callback);
       Serial0PutString("MK8000-文件传输启动\r\n");
//        Get_anchor_appdata_flag=1;
//        HAL_TIM_Base_Start_IT(&htim4);
        while(1)
        {
            if(SerialDownload()==0)
            {
//                Get_anchor_appdata_flag=0;
                g_com_map[YAOGEIANC_UPWENJIAN_FLAG]=0;
                save_com_map_to_flash();  
                delay_ms(300);              
//                Get_anchor_appdata_flag=0;                
                SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader 
                  }
//                  else{
//                  SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader 
//                  }
        }
    }
}
uint16_t final_bag_num;
extern uint8_t Lora_qingqiu_flag;
uint8_t send_lora_data[250];
uint16_t mubiao_anchor_ID;
uint16_t Lora_qingqiu_bao;
uint8_t jindu;
uint8_t shengji_changdu;
uint8_t Dtu_shengji_jindu[20]= {0x55,0xAA,0x34,0x05};
extern uint32_t tempflag;
    uint32_t tx_en_start_u32;
    uint32_t tx_en_start_u321;
uint8_t baifenbi=5;
void Lora_upanc_ing_Poll( void )
{   uint16_t crc16;
//    if(Lora_upanc_flag==1)
//    {
//        Lora_deinit_Poll();
        if(Lora_qingqiu_flag==1)
        {
            CloseUWB();
//            mubiao_anchor_ID=0x1872;
            final_bag_num=(g_com_map[YAOGEIANC_UPWENJIAN_DAXIAO]/ONE_BAG_DAXIAO)+1;//计算一共要发都是包
//            final_bag_num=651;
            Lora_qingqiu_flag=0;
            send_lora_data[MSG_TYPE_IDX]=LORA_MSGTYPE_UPDATEFILE_RESP;//LORA MSG TYPE 定义
            memcpy(&send_lora_data[SOURCE_ID_IDX],&dev_id,2);//自己ID 占用2个字节
            memcpy(&send_lora_data[DEST_ID_IDX],&mubiao_anchor_ID,2);//标签或者基站的设备ID 2个字节
            memcpy(&send_lora_data[MUQIAN_BAG],&Lora_qingqiu_bao,2);
            memcpy(&send_lora_data[DATA_IDX], (HIDO_VOID *)(APP_CONFIG_APPLICATION_ADDRESS+Lora_qingqiu_bao*ONE_BAG_DAXIAO), ONE_BAG_DAXIAO);
            crc16=Cal_CRC16(send_lora_data,DATA_IDX+ONE_BAG_DAXIAO);
            memcpy(&send_lora_data[DATA_IDX+ONE_BAG_DAXIAO],&crc16,2);
//            Lora_status=1;
            jindu=(Lora_qingqiu_bao*100)/final_bag_num;
//            LOG_INFO(TRACE_MODULE_APP, "升级进度%d\r\n",jindu);
            Dtu_shengji_jindu[4]=jindu;
            memcpy(&Dtu_shengji_jindu[5],&mubiao_anchor_ID,2);
            if(jindu>baifenbi)
            {
            uart_send(UART_ID0, Dtu_shengji_jindu,9, NULL);
                baifenbi=baifenbi+10;
            }
            tx_en_start_u32 = phy_timer_count_get()+US_TO_PHY_TIMER_COUNT(100U);//发送必须要延时发送才可以用于测距否则立即发送会获取时间戳不对，需要计算程序运行时间，避免设置过去时间
            tempflag=uwb_tx(send_lora_data,DATA_IDX+ONE_BAG_DAXIAO+2+2,1,tx_en_start_u32);//立即发送  
            tx_en_start_u321= phy_timer_count_get();
//            while(mac_is_busy());//等待发送完成    
            
        }
//    }
}
extern uint8_t shengji_flag;
int main(void)
{
    board_clock_run();
      boot_deinit();
    boot_deinit();
    board_pins_config();
    board_debug_console_open(TRACE_PORT_UART0);
   board_debug_console_open_baud(TRACE_PORT_UART0,BAUD_921600);
    // Reset reason
    reset_cause_get();
    reset_cause_clear();

    Program_Init();
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    sleep_timer_start(__MS_TO_32K_CNT(500));//测试
    Chuanshuwenjian_Poll();
//注意串口一波特率改为9600了为了能和GPS通信上
    // Load calibration parameters from NVM
    uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
    uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
@@ -410,93 +729,149 @@

    // Disable watchdog timer
    wdt_close(WDT_ID0);
    //  LOG_INFO(TRACE_MODULE_APP, "UWB simple example\r\n");
    LOG_INFO(TRACE_MODULE_APP, "UWB simple example\r\n");

    // open system timer
    //sys_timer_open();

    // TODO 4G
    Uart_Register(UART_ID_4G, UART_ID0);
    Internet_Init();
    TCPClient_Init();
//    Uart_Register(UART_ID_4G, UART_ID0);
//    Internet_Init();
//    TCPClient_Init();

    gpio_open();
    //board_led_init();

//      adc_open(&usr_adc_cfg);
    IIC2_Init();
      LED_output_init();//配置adcGND引脚
//      battery_monitor_open();
//      Voltage_input=battery_monitor_get();
//      battery_monitor_close();
	
    adc_open(&usr_adc_cfg);
		
//    IIC2_Init();
    Accelerometer_Init();
    IO_control_init();
    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_OUT, 0);
    io_pull_set(SCL_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
    gps_air780_power_change(1,1);//开启gps，4G 
//      PCA9555_init();
      if(!read_5v_input_pca())
      {
     Set4LEDColor(BLUE,GREEN,WHITE,GREEN);
     delay_ms(500);
     Set4LEDColor(RED,WHITE,RED,WHITE);
     delay_ms(500);		
     //Set4LEDColor(LEDOFF,LEDOFF,LEDOFF,LEDOFF);       
    }
         //IO_control_init();
//    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
//    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
//    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
    //gps_air780_power_change(0,1);//开启gps，4G 
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    uart_open(UART_ID1, &test_uart_cfg);
    Program_Init();
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
      gpio_pin_clr(ADC_GND_ENABLE);
         Program_Init();
    //uart_open(UART_ID1, &test_uart_cfg);
   // uart1_change_from_gps_to_debug();   
    //Uart1GpsRecDebugSend();   
    uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
   
// Initialize low power mode
    power_init();
    //  LOG_INFO(TRACE_MODULE_APP, "测试数据");
   

      //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
    board_5V_input_init(voltage_input_handler);
    sleep_timer_start(__MS_TO_32K_CNT(500));//测试
    //sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
 //   board_5V_input_init(voltage_input_handler);
//         PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
       adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    board_acceleration_detection_init(move_handler);
//       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
    //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
      pca_input_detection_init(pca_handler);//pca检测输入
      Uwb_init();
      OpenUWB();
        LOG_INFO(TRACE_MODULE_APP,"初始化_uwb_rx打开\r\n");
		
      //board_4GUsart_detection_init(_4gUsart_handler);
    while (1)
    {
        if(flag_TCP_reconnectting||IfTCPConnected())
        {
            //   LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
            if(flag_4guart_needinit)
            {
                flag_4guart_needinit = 0;
                AIR780EUartInit();
            }
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();
        }
    { 
        if(!shengji_flag)
         uwb_app_poll();
//         Lora_upanc_ing_Poll();
         //test4=gpio_pin_get_val(SCL_PIN);
         //UWBPoll();
//         if(!power_low_flag)//确认是否休眠下才开启功能
//         {
//        if(flag_TCP_reconnectting||IfTCPConnected())
//        {
//        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
//           
////            if(flag_4guart_needinit)
////            {
////                flag_4guart_needinit = 0;
////                AIR780EUartInit();
////            }//yuan
//                 if(flag_4G_recdata==1)
//            {
//                flag_4G_recdata = 2;
//               
//                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
//                Socket_RecvAll();
//            }
////                  air780_led_on();
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
////            air780_led_off();
//        }
//      }
        if(flag_secondtask)
        {
            flag_secondtask = 0;
            SecondTask();
					
        }
//            PowerTask();
//            IMUTask();
//            UserKeyTask();
        IdleTask();
        //3种情况后都要发包和休眠
        //if(send_flag){
        //message_construct();
        //send_udp;
        //air780_success_state=0;//关闭4G成功发送灯
        //blink_led(&air780_success_state);//成功测距闪烁4G状态灯
        //air780_success_state=0;
        //}
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
    //    if(!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())&&!flag_4G_recdata) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
        {
            //     if(!flag_4guart_needinit)
            {
                //           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
                //             board_4GUsart_detection_init(_4gUsart_handler);
//
            }
//        if(!gps_need_data_flag&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
//        {
//                 if(!flag_4guart_needinit)
//            {
//                           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
//                             board_4GUsart_detection_init(_4gUsart_handler);

//            }
//               flag_sleeptimer =0;
//            LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
            //    flag_4guart_needinit = 1;
//
            //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
//                flag_4guart_needinit = 1;

//        trace_flush();
//        uint32_t lock = int_lock();
//        //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
//        power_enter_power_down_mode(0);
//        int_unlock(lock);
//        }//yuan

            if(delaysleep_count==0)
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
        {
//               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
            uint32_t lock;
            //flag_4guart_needinit = 1;
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
            
           // delay_us(300000);
            trace_flush();
            lock = int_lock();            
            power_enter_power_down_mode(0);
                  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//               test3=gpio_pin_get_val(_4G_USART_RX_Pin);
               //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
            int_unlock(lock);
        }

#endif
    }
}