V1.1铁鞋专属升级工卡，修改uwb配置参数为64len并且修改回包时间让其能测距升级

chen

2025-06-06 3b7f39134908d81041e9550f75169d671f95d0e5

 keil/uwb_app.c

@@ -78,7 +78,7 @@
#define RANGING_PERIOD_MS (1000)

/* This is the delay from Frame RX POLL frame to send RESP Frame */
#define POLL_RX_TO_RESP_TX_DLY_US 550U //yuan600 success 并且不卡busy
#define POLL_RX_TO_RESP_TX_DLY_US 1100U //yuan600 success 并且不卡busy

#define RESP_TX_TO_FINAL_RX_DLY_US 500U

@@ -116,14 +116,14 @@
    uint8_t phy_work_mode; /* PHY_TX / PHY_RX / PHT_TX|PHY_RX */
    struct UWB_CONFIG_T phy_cfg;
};

extern uint8_t uwb_ch;
static struct mk_uwb_configure config = {
    .phy_work_mode = (uint8_t)(PHY_TX | PHY_RX),
    .phy_cfg.ch_num = 5,                      /* Channel number.                           */
    .phy_cfg.code_index = 9,                  /* TRX preamble code                         */
    .phy_cfg.mean_prf = MEAN_PRF_64M,         /* Mean prf 64/128/256M                      */
    .phy_cfg.data_bit_rate = DATA_BR_6M8,     /* Data rate 6.8M                            */
    .phy_cfg.sync_sym = PREAM_LEN_128,        /* Preamble duration, length of preamble 128 */
    .phy_cfg.sync_sym = PREAM_LEN_64,        /* Preamble duration, length of preamble 128 */
    .phy_cfg.sfd_sym = NON_STD_NSFD5_8,          /* Identifier for SFD sequence               */
    .phy_cfg.ranging_bit = 1,                 /* ranging bit set 1                         */
    .phy_cfg.trx_mode = TRX_MODE_15_4A,  /* IEEE802.15.4z - BPRF mode                 */
@@ -230,6 +230,8 @@
extern uint16_t mubiao_anchor_ID;
uint8_t Lora_qingqiu_flag;
extern uint16_t Lora_qingqiu_bao;
uint8_t shengji_flag;
extern uint8_t Dtu_shengji_jindu[20];
static void rx_int_callback(struct MAC_HW_REPORT_T *rx_report)
{      uint8_t valid_sts=0;
    uint16_t checksum1 = 0,dest_id;
@@ -251,7 +253,8 @@
        rssi = rx_report->rssi;
        receive_flag=1;
//        uart_send(UART_ID0, rx_buf,rx_length, NULL);
        if(rx_buf[MESSAGE_TYPE_IDX]==MBX_POLL)
        gpio_pin_toggle(IO_PIN_4);
        if(rx_buf[MESSAGE_TYPE_IDX]==MBX_POLL&&!shengji_flag)
        {
        Anchor_App();
        }
@@ -264,6 +267,7 @@
            {
                if(!memcmp(&dev_id,&dest_id,2)/*||dest_id==0xffff||(dest_id==0xfffe&&get_channel==5)*/)
                {
                    shengji_flag=1;
                    switch(rx_buf[MSG_TYPE_IDX])
                    {
                    case LORA_MSGTYPE_UPDATE_CONFIRM:
@@ -285,8 +289,13 @@
                        break;
                    
                    case 0x99:
                    LOG_INFO(TRACE_MODULE_APP, "收到结束升级请求\r\n",Lora_qingqiu_bao);
                        delay_ms(500);
//                    LOG_INFO(TRACE_MODULE_APP, "收到结束升级请求\r\n",Lora_qingqiu_bao);
                    delay_ms(200);
                    Dtu_shengji_jindu[4]=100;
                    memcpy(&Dtu_shengji_jindu[5],&mubiao_anchor_ID,2);
                    uart_send(UART_ID0, Dtu_shengji_jindu,9, NULL);
                    
                        delay_ms(1000);
//                        Lora_upanc_flag=0;
                        Lora_qingqiu_flag=0;
                        NVIC_SystemReset();
@@ -317,7 +326,7 @@
//            }
            }
        }
				

         #ifdef STS_MODE
            valid_sts= sts_valid_check();
      if (valid_sts)
@@ -518,6 +527,11 @@
                //while(mac_is_busy());
                gpio_pin_clr(SCL_PIN);
                cmd_flag=1;
                if(send_buffer[RW_FLAG_IDX]==0x01)
                {
                delay_ms(100);
                NVIC_SystemReset();    
                }
                break;
            }
        }
@@ -644,6 +658,33 @@

   if(HIDO_TimerGetTick()-uwbtasktimer >=1)
   {
            
    for(uint16_t i=0;i<taglist_num-1;i++)
    {
        for(uint16_t j=0;j<taglist_num-1-i;j++)
        {
            if(tagdist_list[j]>tagdist_list[j+1])
            {
                uint16_t id,dist,version;
                uint8_t bat;
                id = tagid_list[j];
                dist = tagdist_list[j];
                version = anchordata_version[j];
                tagid_list[j] = tagid_list[j+1];
                tagdist_list[j] = tagdist_list[j+1];
                anchordata_version[j] = anchordata_version[j+1];
                tagid_list[j+1] = id;
                tagdist_list[j+1] = dist;
                anchordata_version[j+1] = version;
            }
        }
    
    }
    
        if(taglist_num>6)
        {
        taglist_num=6;
        }
      uwbtasktimer = HIDO_TimerGetTick();
      UWBOneSecondTask();
        uwbsend[0]=0x55;
@@ -654,6 +695,7 @@
        memcpy(&uwbsend[4+taglist_num*2],&tagdist_list,taglist_num*2);
        memcpy(&uwbsend[4+taglist_num*4],&anchordata_version,taglist_num*2);
        uart_send(UART_ID0, uwbsend,taglist_num*6+4, NULL);
        taglist_num=0;
//        for(int i=0;i<anchordata_num;i++)
//        {
//        LOG_INFO(TRACE_MODULE_APP,"当前测距基站ID:%x,距离:%d.\r\n",tagid_list[0],tagdist_list[0]);
@@ -879,6 +921,7 @@
    phy_rx_ant_mode_set(RX_ANT_PORTS_COMBINATION);
   #endif
    // Set calibration parameters
//    config.phy_cfg.ch_num=g_com_map[NEARBASE_ID1];
    uwb_calibration_params_set(config.phy_cfg.ch_num);
   #ifndef STS_MODE
   // set advanced parameters