11111111111111

WXK

2025-03-12 3ec132c58bc4130f79390cebca35c176173cb67c

 keil/include/main/main.c

@@ -61,8 +61,10 @@
#include "HIDO_ATLite.h"
#include "HIDO_Timer.h"
#include "TCPClient.h"
#include "PCA9555.h"
#include "WS2812.h"

#define DEBUG_MODE
//#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
#define TEST_UART_POLL_MODE 0
@@ -98,6 +100,11 @@
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1;  //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
extern uint8_t pca9555writedata_config[10];//暂存寄存器所有配置的数组
extern uint8_t pca9555writedata_output[10];//暂存输出高低电平配置的数组
extern uint8_t pca9555writedata_input[10];//暂存输入寄存器所有配置的数组
extern uint8_t pca9555writedata_polarity[10];//暂存输入极性反转寄存器所有配置的数组
uint8_t temp_pca9555writedata_input[10];//暂存上一次输入寄存器所有配置的数组
typedef enum
{      UN_BIND=0,
        LINK_SUCCESS,
@@ -153,11 +160,13 @@
            trace_flush();
            lock = int_lock();
                  LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  gps_air780_power_change(0,0);//关闭gps，4G 
//                  gps_air780_power_change(0,0);//关闭gps，4G 
            PCA9555_Set_One_Value_Output(GPS_POWER,0);//关闭gps，4G 
            PCA9555_Set_One_Value_Output(AIR780E_ENBALE,0);//关闭gps，4G 
                     sleep_timer_stop();   
                  //adc_close();
            power_enter_power_down_mode(1);
                  //LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  LOG_INFO(TRACE_MODULE_APP, "从休眠出来\r\n");
                  sys_reset(0);
            int_unlock(lock);
}
@@ -185,135 +194,116 @@
    }
            if(fVoltage_mv<3300)
            {
               power_low_flag=1;
               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               //power_low_flag=1;
               //gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
            }else{
               power_low_flag=0;
               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               //power_low_flag=0;
               //gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
      gpio_pin_set(ADC_GND_ENABLE);//在拉高
      PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
//void UartInit(void)
//{
//board_pins_config();
//uart_open(UART_ID1, &test_uart_cfg);
//board_debug_console_open(TRACE_PORT_UART0);
//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//}
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2;
uint32_t keystarttime,keystarttime2,keystarttime3;
extern uint32_t get_in_num,get_out_num;
void MotorPoll(void)
{
    if(UWB_work_state==UN_BIND) {
        gps_uwb_flag=0;//关闭GPS
        moter_open_uwb_flag=0;//关闭震动
        need_open_gps_count=0;//清0计数gps
    } else { //绑定状态下
        if(anchordata_num==1) {
            if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                fenli_alarm_count = 0;
                if(flag_fenli_alarm)
                {
                    flag_fenli_alarm = 0;
                    fenli_alarm_count = 0;
                    _4GAlarmUpload(2);
                }
            } 
            }
            if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
                     {
                if(fenli_alarm_count++>20)
                {
                           if(!flag_fenli_alarm)
                           {
                    flag_fenli_alarm = 1;
                    _4GAlarmUpload(1);
                           }
                }
                     }
                 if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                if(flag_alam_state)
                {
                    flag_alam_state = 0;

                }		
							
                need_open_gps_count=0;
                moter_open_uwb_flag=0;//关闭震动
                gps_uwb_flag=0;//关闭GPS
            } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            
        } 
                  if(anchordata_num==0) {
            if(!flag_alam_state)
            {
                flag_alam_state = 1;
            }
            distance = 0x1ffff;
            gps_uwb_flag=1;//开启gps测距流程
            moter_open_uwb_flag=1;//开启震动
            need_open_gps_count=0;
        }
    }
   }
uint8_t flag_4G_recdata;
uint8_t ledonflag;
uint32_t ledontime;
void IMUTask(void)
{
   if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
   {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
   {//power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
      mcu_deep_sleep();
   }
}
void UserKeyTask(void)
 {
     if(!GET_USERKEY)
{
if(!read_userkey_input_pca())
     {
        if(HIDO_TimerGetTick() - keystarttime>3)
        if(HIDO_TimerGetTick() - keystarttime3>2)
        {
            userkey_state = 1;
            keystarttime =  HIDO_TimerGetTick();
                  UDPClient_UploadGPS();
            keystarttime3 =  HIDO_TimerGetTick();
                  //UDPClient_UploadGPS();
        }
        if(HIDO_TimerGetTick() - keystarttime2>10)
//        if(HIDO_TimerGetTick() - keystarttime2>10)
//        {
//						
//            g_com_map[CNT_RESTART] = 1;
//        }
     }else
     {
       keystarttime3 =  HIDO_TimerGetTick(); 
     }
} 
void PowerTask(void)
{
     if(read_powerkey_input_pca())
     {
        if(HIDO_TimerGetTick() - keystarttime>2)
        {
            g_com_map[CNT_RESTART] = 1;
              rtkled=WHITE;
              uwbled=WHITE;
              led4g=WHITE;
              powerled=WHITE;
              Set4LEDColor(uwbled,rtkled,led4g,powerled);
            delay_ms(500);
            keystarttime =  HIDO_TimerGetTick();
            PCA9555_Set_One_Value_Output(LED_POWER,0);//输出低电平关闭LED
            PCA9555_Set_One_Value_Output(AIR780E_ENBALE,0);
            PCA9555_Set_One_Value_Output(GPS_POWER,0);//关GPS
            PCA9555_Set_One_Value_Output(PWR_ENABLE,0);//低电平关闭

        }
//        if(HIDO_TimerGetTick() - keystarttime2>10)
//        {
//						
//            g_com_map[CNT_RESTART] = 1;
//        }
     }else
     {
       keystarttime =  HIDO_TimerGetTick(); 
       keystarttime2 =  HIDO_TimerGetTick(); 
     }
 } 
}
void MinuteTask(void)
{      gpio_pin_clr(ADC_GND_ENABLE);//拉低
{		
      PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
void Air780eTask(void)
{
//         if(!power_low_flag)//确认是否休眠下才开启功能
//         {
        if(flag_TCP_reconnectting||IfTCPConnected())
        {
//        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
//           
////            if(flag_4guart_needinit)
////            {
////                flag_4guart_needinit = 0;
////                AIR780EUartInit();
////            }//yuan
         if(flag_4G_recdata==1)
            {
                flag_4G_recdata = 2;
               
                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
                Socket_RecvAll();
            }
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();

        }
//      }

}
void SecondTask(void)
{static uint8_t second_count;
@@ -322,86 +312,95 @@
        second_count = 0;
        MinuteTask();
    }
      TagListUpdate_person_num_car();
      in_table_log();
		
//      if(!power_low_flag)
//      Gps_change();
//      else{
//      gps_power_state=0;//关闭GPS
//      update_led_power_state();
//      //初始化GPS计数数据
//      gps_need_data_flag=1;
//      gps_wait_count2=0;
//      gps_wait_count=0;
//      }
//    //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
//   {
//    if(IfTCPConnected())
//    {
//        TCP_reconnect_timer =0;
//        flag_TCP_reconnectting = 0;
//    } else {
//        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
//        {
//            flag_TCP_reconnectting = 1;
//        } else {
//            flag_TCP_reconnectting = 0;
//        }
//        if(TCP_reconnect_timer++>600)
//        {
//            TCP_reconnect_timer = 0;
//        }
    //UWB状态检测
if(!power_low_flag)//低供电下不需要检测重连
   {
    if(IfTCPConnected())
    {
        TCP_reconnect_timer =0;
        flag_TCP_reconnectting = 0;
    } else {
        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
        {
            flag_TCP_reconnectting = 1;
        } else {
            flag_TCP_reconnectting = 0;
        }
        if(TCP_reconnect_timer++>600)
        {
            TCP_reconnect_timer = 0;
        }

//    }
//   }
    }
   }
    HIDO_TimerTick();
      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
//      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
    nomove_count++;
      else{
      nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
      }
//      else{
//      nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
//      }
}
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
uint8_t input5v_time;
extern uint8_t taglist_num;
static void sleep_timer_callback(void *dev, uint32_t time)
{
    IO_control_init();
      if(enbale_blink_flag)
   {
   green_charge_state=0;
   charge_red_on();
   }
	 
   charge_state_change();//充电状态判断
if(secondtask_count++%2==0)
    {
    {   
        input5v_time=1;
        flag_secondtask = 1;
        if(!read_5v_input_pca())
        {
        if(bat_percent>15)
        {
            powerled = BLUE;
        }else{
             powerled = RED;
        }
        ledonflag=1;
//        ledontime=HIDO_TimerGetTick();
        Set4LEDColor(uwbled,rtkled,led4g,powerled); 
        }
        input5v_time=1;
        if(taglist_num==0)
        {
        CloseUWB();
        Uwb_init();
        OpenUWB();
        }
    }else{
        flag_secondtask = 0;
    }
      if(enbale_blink_flag)
   {
      //delay_us(5000);
   green_charge_state=0;
   charge_red_off();
   }		
 if(delaysleep_count>0)
     delaysleep_count--;
    //GPS工作逻辑
}
uint8_t test11,test21,test31,test41,test51;
static void pca_handler(enum IO_PIN_T pin)
{
   PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
   uint16_t gpio_state;
   gpio_state=(uint16_t)pca9555writedata_input[0]<<8|pca9555writedata_input[1];
    test41++;
   if(WAKE_UP_POSITION&gpio_state)
   {
      nomove_count=0;
        test11++;
   }
//   if(!(MAIN_RI_POSITION&gpio_state))
//   {
//       flag_4G_recdata = 1;
//     delaysleep_count = 3;
//        test21++;
//   }
    if((PWR_ON_POSITION&gpio_state))
   {
        PowerTask();
        test31++;
   }
}

static void voltage_input_handler(enum IO_PIN_T pin)
{

}
static void move_handler(enum IO_PIN_T pin)
{
    nomove_count=0;
}
uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
{
     //LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
@@ -410,12 +409,13 @@
}
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
uint8_t gps_need_data_flag,gps_open_flag;
void Program_Init(void)
{
    Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
    parameter_init_anchor();//g_com_map表初始化角色默认为基站
    dev_id=g_com_map[DEV_ID];//这里不太对
    g_com_map[GROUP_ID]=9;
    group_id=g_com_map[GROUP_ID];//组ID
//    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
    memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
@@ -448,64 +448,117 @@
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|0;
    g_com_map[VERSION] = (1<<8)|3;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}



uint32_t adctick = 0;
uint8_t only_one_flag;
uint16_t chongman_time;
uint8_t bat_percent_old=100;
uint8_t input5vflag;
void IdleTask(void)
{
//    if(gpio_pin_get_val(INPUT_5V_Pin))
//    {

//        if(state5v==0)
//        {
//            state5v=1;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=0;//解除gps解析
//            uart1_change_from_gps_to_debug();//测试
//         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartInit();
//        }

//        //UART_CheckSend();
//    } else {
//        if(state5v==1)
//        {
//            g_com_map[MODBUS_MODE] = 0;
//            state5v=0;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=1;//恢复gps解析
//            uart1_change_from_debug_to_gps();//测试
//          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartDeinit();
//        }
//    }
if(read_5v_input_pca())
      {
            if(state5v==0)
            {
                state5v=1;
                state5V_prase_flag=state5v;
                gps_prase_flag=0;//解除gps解析
                uart1_change_from_gps_to_debug();//测试
                PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
            } 
            chongman_time=0;
            only_one_flag=0;
            uwbled=0;
            rtkled=0;
            led4g=0;
            powerled=0;
//            PCA9555_Set_One_Value_Output(AIR780E_ENBALE,0);
            while(1)
            {
                nomove_count = 0;
                if(HIDO_TimerGetTick()-adctick>6000)  //10分钟采样一次 电量
                {
                    chongman_time=chongman_time+6;
                    adctick = HIDO_TimerGetTick();
                    PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
                    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
                }
                if(bat_percent>=99&&!only_one_flag)
                {
                only_one_flag=1;
                chongman_time=0;
                }
                if(bat_percent>=99&&chongman_time>=1800)
                {
                    powerled = GREEN;
                }else{
                    powerled = RED;
                }
                UART_CheckReceive();
                Internet_Poll();
                HIDO_TimerPoll();
                HIDO_ATLitePoll();
                TCPClient_Poll();
                if(flag_secondtask)
                {
                    flag_secondtask = 0;
                    SecondTask();
                }
                Set4LEDColor(0,0,0,powerled);
                if(input5v_time)
                {
                if(!read_5v_input_pca())
                {
                break;
                }
                }
            }
            NVIC_SystemReset();
            input5vflag=1;
      }
        else 
        {
            if(state5v==1)
            {
                g_com_map[MODBUS_MODE] = 0;
                state5v=0;
                state5V_prase_flag=state5v;
                gps_prase_flag=1;//恢复gps解析
                uart1_change_from_debug_to_gps();//测试
                            PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
            }
//            input5vflag=0;
        }
      UART_CheckReceive();
}
int bind_check(void)
{
    if(g_com_map[BIND_DEV_ID]!=0x00)
    {
        return 1;
//绑定信息为1说明设备已经被下发绑定
    } else {
        return 0;
//绑定信息为0说明设备未被绑定
    }
}
void check_if_in_search(void)
{
    if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
        UWB_work_state=LINK_SUCCESS;
    } else { //否则进入搜索模式
        UWB_work_state=SEARCH_DEV;
        if(first_search_flag==0)
            first_search_flag=1;
    }
        if(g_com_map[CNT_RESTART]==1)
        {
            g_com_map[CNT_RESTART]=0;
//            printf("%s URTRestart",__debug_info__);
//            URTRestart(); 
            NVIC_SystemReset();
            
        }
        if(g_com_map[MAP_SIGN_INDEX]!=0x55AA||g_com_map[COM_INTERVAL]==0)
        {
//            printf("%s URTRestart",__debug_info__);
//            URTRestart();
//              //  SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
            NVIC_SystemReset();
        }
        HIDO_TimerPoll();
        if(ledonflag==1)
        {
        ledonflag=0;
        uwbled=0;
        rtkled=0;
        led4g=0;
        powerled=0;
        Set4LEDColor(LEDOFF,LEDOFF,LEDOFF,LEDOFF); 
        }
}
void boot_deinit(void)
{
@@ -525,17 +578,17 @@
int tt2;
int test1,test3;
uint32_t test4;

extern uint8_t receive_flag;
int main(void)
{
    board_clock_run();
    boot_deinit();
    board_pins_config();
    board_debug_console_open(TRACE_PORT_UART1);
      board_debug_console_open_baud(TRACE_PORT_UART1,BAUD_115200);
    // Reset reason
    reset_cause_get();
    reset_cause_clear();

//注意串口一波特率改为9600了为了能和GPS通信上
    // Load calibration parameters from NVM
    uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
    uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
@@ -559,126 +612,113 @@

    // open system timer
    //sys_timer_open();

    // TODO 4G
      // TODO 4G
    Uart_Register(UART_ID_4G, UART_ID0);
//    Internet_Init();
//    TCPClient_Init();

    Internet_Init();
    TCPClient_Init();
    gpio_open();
      board_output_init();//配置adcGND引脚
//      battery_monitor_open();
//      Voltage_input=battery_monitor_get();
//      battery_monitor_close();
    adc_open(&usr_adc_cfg);
		
    LED_output_init();//配置彩色灯引脚
    IIC2_Init();
    Accelerometer_Init();
    IO_control_init();
    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
    //gps_air780_power_change(0,1);//开启gps，4G 
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
      gpio_pin_clr(ADC_GND_ENABLE);
   
    PCA9555_init();
 
		
      //AIR780E_Reset(); 
	
    adc_open(&usr_adc_cfg);
		
    if(!read_5v_input_pca())
    {
     Set4LEDColor(BLUE,GREEN,WHITE,RED);
     delay_ms(500);
     Set4LEDColor(RED,WHITE,RED,WHITE);
     delay_ms(500);		
     Set4LEDColor(LEDOFF,LEDOFF,LEDOFF,LEDOFF);       
    }
//    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
//    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
//    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
         Program_Init();
    //uart_open(UART_ID1, &test_uart_cfg);
 
   // uart1_change_from_gps_to_debug();   
    //Uart1GpsRecDebugSend();   
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
   
// Initialize low power mode
   // Initialize low power mode
    power_init();
      //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    //sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
 //   board_5V_input_init(voltage_input_handler);
    //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
      PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
       adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    board_acceleration_detection_init(move_handler);
//       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
      board_4GUsart_detection_init(_4gUsart_handler);
    //board_acceleration_detection_init(move_handler);
      pca_input_detection_init(pca_handler);//pca检测输入
      //board_4GUsart_detection_init(_4gUsart_handler);
      Uwb_init();
      OpenUWB();
//                        state5v=1;
//                state5V_prase_flag=state5v;
//                gps_prase_flag=0;//解除gps解析
//                uart1_change_from_gps_to_debug();//测试
//                PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
    while (1)
    { test4=gpio_pin_get_val(SCL_PIN);
         UWBPoll();
//         if(!power_low_flag)//确认是否休眠下才开启功能
//         {
//        if(flag_TCP_reconnectting||IfTCPConnected())
//        {
//        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
//           
////            if(flag_4guart_needinit)
////            {
////                flag_4guart_needinit = 0;
////                AIR780EUartInit();
////            }//yuan
//                 if(flag_4G_recdata==1)
//            {
//                flag_4G_recdata = 2;
//               
//                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
//                Socket_RecvAll();
//            }
////                  air780_led_on();
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
////            air780_led_off();
//        }
//      }
    { 
      uwb_app_poll();
        Internet_Poll();
        HIDO_TimerPoll();
        HIDO_ATLitePoll();
        TCPClient_Poll();
        if(flag_secondtask)
        {
            flag_secondtask = 0;
            SecondTask();
					
        }
//            UserKeyTask();
//            IMUTask();
      PowerTask();
      IMUTask();
      UserKeyTask();
        IdleTask();
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
//        if(!gps_need_data_flag&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
////if(flag_sleeptimer)
////        if(!gps_need_data_flag&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
////        {
////                 if(!flag_4guart_needinit)
////            {
////                           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
////                             board_4GUsart_detection_init(_4gUsart_handler);

////            }
////               flag_sleeptimer =0;
//            //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
////                flag_4guart_needinit = 1;

////        trace_flush();
////        uint32_t lock = int_lock();
////        //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
////        power_enter_power_down_mode(0);
////        int_unlock(lock);
////        }//yuan

//            if(delaysleep_count==0)
//        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
//        {
//                 if(!flag_4guart_needinit)
//            {
//                           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
//                             board_4GUsart_detection_init(_4gUsart_handler);

//            }
//               flag_sleeptimer =0;
            //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
//                flag_4guart_needinit = 1;

//        trace_flush();
//        uint32_t lock = int_lock();
//        //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
//        power_enter_power_down_mode(0);
//        int_unlock(lock);
//        }//yuan

            if(delaysleep_count==0)
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
        {
//               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
            uint32_t lock;
            //flag_4guart_needinit = 1;
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
            
           // delay_us(300000);
            trace_flush();
            lock = int_lock();            
            power_enter_power_down_mode(0);
                  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//               test3=gpio_pin_get_val(_4G_USART_RX_Pin);
               //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
            int_unlock(lock);
        }
////               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
//            uint32_t lock;
//            //flag_4guart_needinit = 1;
////            Internet_Poll();
////            HIDO_ATLitePoll();
////            HIDO_TimerPoll();
////            TCPClient_Poll();
//            
//           // delay_us(300000);
//            trace_flush();
//            lock = int_lock();            
//            power_enter_power_down_mode(0);
//                  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
////               test3=gpio_pin_get_val(_4G_USART_RX_Pin);
//               //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
//            int_unlock(lock);
//        }

#endif
    }