注释掉了串口逻辑，加入了与蓝牙串口通信逻辑，能够修改参数，但网关下发配置会出现hardfault未解决

chen

6 天以前 62f6fe8e906f8c17493d154f5567ba8a7ab4c0cf

 keil/include/src/Radio/lora_1268.c

@@ -313,7 +313,7 @@
   checksum = Checksum_u16(lora_sendbuffer,9+data_length);
   memcpy(&lora_sendbuffer[9+data_length],&checksum,2);
   Radio.Send(lora_sendbuffer,data_length+11);

LOG_INFO(TRACE_MODULE_APP, "进入回复\r\n");
  //LORA_3029_SINGLE_SEND(lora_sendbuffer,data_length+11,0);
  //  Delay_Ms(100);
}
@@ -360,7 +360,19 @@

     
}

void lora_in_sleep(void)
{
             //SPI0/MOSI/MISO/CLK/CS
//   gpio_pin_set(LORA_CS);
//   gpio_pin_clr(LORA_MOSI);
//   gpio_pin_clr(LORA_MISO);
//   gpio_pin_clr(LORA_CLK);
//   gpio_pin_clr(LORA_IRQ);
   //gpio_pin_clr(LORA_NRST);
   //gpio_pin_clr(LORA_NRST);//lora休眠
    Radio.Standby();
    Radio.Sleep();
}
////States_t State = LOWPOWER;

//////int8_t RssiValue = 0;
@@ -377,9 +389,11 @@
//uint16_t current_count;
//extern wg_state_enum wg_state;
uint8_t txdone=0;
uint8_t send_flag;
void OnTxDone( void )
{ 
     txdone++;
		
    if(flag_writepara_needreset) //配置写入完成设备需要重启
    {
        printf("网关下发配置写入完成，重启");
@@ -393,7 +407,9 @@
    }
    else
    {
			
    Radio.Rx( 50 );
         send_flag=1;
    //LORA_LED_OFF;
    }
}
@@ -427,6 +443,8 @@
uint8_t LoraUp_flag;
uint16_t REV_WG_pack=0; 
uint8_t rxdone=0;
extern uint16_t set_mk_time;
extern mk_send_message_to_BLE(void);
void OnRxDone( uint8_t *payload, uint16_t size, int16_t rssi, int8_t snr )
{  
            uint16_t checksum1;
@@ -516,7 +534,13 @@
                        default :
                            memcpy(&rec_value,&RX_Buffer[PWTAG_WRITE_VALUE_IDX],2);
                            g_com_map[rec_index/2] = rec_value;
                            save_com_map_to_flash();
//                                          if(rec_index/2==POWER)//新增判断
//                                          {
//                                           memcpy(&set_mk_time,&RX_Buffer[PWTAG_WRITE_VALUE_IDX],2);
//                                             //mk_send_message_to_BLE();   //发送给蓝牙
//                                             //LOG_INFO(TRACE_MODULE_APP, "修改成功g_com表为%#x,时间为%#x\r\n",g_com_map[POWER],set_mk_time);
//                                          }
                           // save_com_map_to_flash();
                            LoraRspWriteCommap(SUBMSG_WRITE_ANCPARA);
                            flag_writepara_needreset = 1;
                            no_rx_flag = 1;                           
@@ -546,7 +570,8 @@
                           }
                        }

                     }						
                     }
LOG_INFO(TRACE_MODULE_APP, "进入回复2\r\n");						
    if(!no_rx_flag)
    {
        if(lora_jianting_flag&&LoraUp_flag==0)
@@ -570,6 +595,7 @@
void OnRxTimeout( void )
{
    Radio.Standby();
	
    if(lora_jianting_flag)
    {
        SwitchLoraSettings(UWB_CHANNEL_FRQ+group_id,UWB_CHANNEL_SF,0);