1.9，加入电量新计算方法 测试电池能干多久问题 目前1s检测一下adc

WXK

2 天以前 7d13fbde75b58ff4c9deaef95ca0c03a1083f8e8

 keil/include/main/main.c

@@ -68,7 +68,7 @@
#include "mk_phy.h"
#include "mk_pwm.h"

#define DEBUG_MODE
//#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
void uart_change_check(uint16_t gpio_state);
@@ -183,31 +183,32 @@
//        LOG_INFO(TRACE_MODULE_APP, "The voltage measured %d mv\r\n",
//        ADC_INTERNAL_VREF_MV + adc_code_to_mv((int16_t)*result, ADC_INTERNAL_VREF_MV));
        fVoltage_mv=ADC_INTERNAL_VREF_MV + adc_code_to_mv((int16_t)*result, ADC_INTERNAL_VREF_MV);
        fVoltage_mv=fVoltage_mv*2;
        if(fVoltage_mv < 3300)
        fVoltage_mv=fVoltage_mv*2+1100;
        if(fVoltage_mv < 2000)
        {
            bat_percent = 0;
        }
        else if(fVoltage_mv > 4100)
        else if(fVoltage_mv > 3100)
        {
            bat_percent = 100;
        }
        else
        {
            bat_percent = ((fVoltage_mv - 3300) /8);
            bat_percent = ((fVoltage_mv - 2000) /11);
        }
    }
            if(fVoltage_mv<3300)
            {
               power_low_flag=1;
               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               //LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
            }else{
               power_low_flag=0;
               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               //LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
      PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
//    LOG_INFO(TRACE_MODULE_APP, "当前静止:%d 电量:%d\r\n",nomove_count,fVoltage_mv);
//            if(fVoltage_mv<3300)
//            {
//               power_low_flag=1;
//               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
//               //LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
//            }else{
//               power_low_flag=0;
//               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
//               //LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
//            }
//      PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
extern uint8_t gps_uwb_flag,gps_need_data_flag;
@@ -219,7 +220,9 @@
void IMUTask(void)
{
   if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
   {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
   {
        LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
        power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
      mcu_deep_sleep();
   }
}
@@ -266,16 +269,18 @@
}
void MinuteTask(void)
{      
      PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
//      PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
//uint16_t adc_count;
//uint8_t adc_start_flag;
void SecondTask(void)
{static uint8_t second_count;
    if(second_count++>60)
    {
        second_count = 0;
        MinuteTask();
    }
//    if(adc_count++>3600&&adc_start_flag)
//    {
//        adc_count = 0;
//        MinuteTask();
//    }
      
//      if(!power_low_flag)
//      Gps_change();
@@ -342,8 +347,9 @@
uint8_t Get_anchor_appdata_flag;
uint8_t Get_anchor_appdata_num;
extern uint8_t update_tag_time;
uint8_t sleep_limit_time=1;
uint8_t sleep_limit_time=10;
uint8_t enable_sleep_count,sleep_flag;
extern  float motor_keeptime;
static void sleep_timer_callback(void *dev, uint32_t time)
{
 
@@ -354,7 +360,10 @@
    enable_sleep_count=0;
    sleep_flag=1;
    }
    
    if(motor_keeptime>0)
    {
    motor_keeptime--;
    }
    
    g_start_send_flag=1;
//    if(delaysleep_count>0)
@@ -365,7 +374,9 @@
static void move_handler(enum IO_PIN_T pin)
{
    nomove_count=0;
    Motion_Detection_callback();
//    LOG_INFO(TRACE_MODULE_APP, "加速度唤醒了\r\n");
//    LOG_INFO(TRACE_MODULE_APP, "当前静止:%d 电量:%d\r\n",nomove_count,fVoltage_mv);
//    Motion_Detection_callback();
}
static void pca_handler(enum IO_PIN_T pin)
{
@@ -420,7 +431,7 @@
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|4;
    g_com_map[VERSION] = (1<<8)|9;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
@@ -504,7 +515,7 @@
        if(state5v==1)
        {
        state5v=0;
        sleep_limit_time=1;//新增插入串口后30s不休眠
        sleep_limit_time=10;//新增插入串口后30s不休眠
        enable_sleep_count=0;//重新插拔可以重置时间
        }

@@ -617,6 +628,9 @@

}
extern uint8_t shengji_flag;
extern uint16_t adc_caiji;
uint8_t send_frame1[10];
extern uint8_t adc_one;
int main(void)
{
    board_clock_run();
@@ -646,7 +660,7 @@
    LOG_INFO(TRACE_MODULE_APP, "UWB simple example\r\n");
    
    struct PWM_CFG_T usr_pwm_cfg = {
        .general_prescale = 15,
        .general_prescale = 7,
        .int_en = 1,
        .callback = pwm_callback,
    };
@@ -658,7 +672,7 @@
      
    IIC2_Init();
    SC7A22H_Motion_Detection_Init();
    gpio_pin_clr(ADC_GND_ENABLE);
//    gpio_pin_clr(ADC_GND_ENABLE);
    Program_Init();
    uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
    power_init();
@@ -670,10 +684,11 @@
    sleep_timer_start(__MS_TO_32K_CNT(5000));//测试
    #endif
    board_5V_input_init(voltage_input_handler);
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
//    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    board_acceleration_detection_init(move_handler);
    Uwb_init();
    Dw1000_App_Init();
//    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    while (1)
    { 
        if(flag_secondtask)
@@ -683,8 +698,33 @@
        }
        if(g_start_send_flag)
        {
            
//                adc_caiji++;
//    if(adc_caiji>5&&adc_one==0)
//    {
//    adc_one=1;  
//    adc_caiji=0;  
//    MinuteTask();
//    }
//    else if(adc_one==1&&adc_caiji>3600)
//    {
//    adc_caiji=0;  
//    MinuteTask(); 
//    }
    
//    send_frame1[0] = 0x55;
//    send_frame1[1] = 0xAA;
//    send_frame1[2] = nomove_count;
//    memcpy(&send_frame1[3],&fVoltage_mv,2);        
////    send_frame1[3] = data_length+5;
////    send_frame1[4] = CMD_REPLY;
////    send_frame1[5] = index;
////    send_frame1[6] = data_length;
//    uart_send(UART_ID0, send_frame1,5, NULL);
    
            g_start_send_flag = 0;
            gpio_pin_set(IO_PIN_7);//亮
//            LOG_INFO(TRACE_MODULE_APP, "当前静止:%d 电量:%d\r\n",nomove_count,fVoltage_mv);
          SwitchTagState();   
            gpio_pin_clr(IO_PIN_7);//灭
        }
@@ -695,7 +735,7 @@
        LoraUp_Poll();
#ifndef DEBUG_MODE
        
         if(sleep_flag&&state5v==0){//开始一段时间无休眠
         if(sleep_flag&&state5v==0&&motor_keeptime==0){//开始一段时间无休眠
                  trace_flush();
            uint32_t lock = int_lock();
                  //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");