开发完成

WXK

9 天以前 31a18a379b5d7073705895dba364ca3b76d5d44e

 keil/include/main/main.c

@@ -118,6 +118,7 @@
uint8_t group_id,enable_sleep_count;
uint32_t dev_id;
uint16_t disoffset;
uint16_t set_mk_time;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count;
float nomove_count;
// Default pool descriptor.
@@ -129,6 +130,8 @@
{
    // LOG_INFO(TRACE_MODULE_APP, "Wake up by sleep timer %d\r\n", time);
}
extern uint8_t start_wait_flag;
extern int16_t end_count1;
static void sleep_timer_callback_normal(void *dev, uint32_t time)
{
   if(secondtask_count++%2==0)
@@ -137,12 +140,18 @@
    }else{
        flag_secondtask = 0;
    }
      if(start_wait_flag)//lora升级等待超时标志
      {
      if(end_count1--<=0)
      start_wait_flag=0;
      }
// if(delaysleep_count>0)
//     delaysleep_count--;
}
void Program_Init(void)
{
    Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
		
    parameter_init_anchor();//g_com_map表初始化角色默认为基站
    dev_id=g_com_map[DEV_ID];//这里不太对
    group_id=(uint8_t)g_com_map[GROUP_ID];//组ID
@@ -168,7 +177,11 @@
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|0;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
//      if(gpio_pin_get_val(MODE_CHANGE_PIN))
//    LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_Air_tag模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
//      else{
//      LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_免布线模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
//      }
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}
void MinuteTask(void)
@@ -182,12 +195,14 @@
}
void SecondTask(void)
{static uint8_t second_count;
	
    if(second_count++>60)
    {
        second_count = 0;
        MinuteTask();
    }
      lora_tx_flag=1;
   lora_tx_flag=1;
		
      //Lora_Tx_Poll();
//    //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
@@ -296,11 +311,12 @@
    // Configure IO_04 for RF Switch
    gpio_pin_set_dir(IO_PIN_4, GPIO_DIR_OUT, 0);
#else
      Program_Init();

      spi_init();
    // 模式判断脚和spi nrst脚初始化
//    // 模式判断脚和spi nrst脚初始化
    board_mode_pin_init();
//    board_led_on(BOARD_LED_1);
    Program_Init();
    //board_led_on(BOARD_LED_1);
#endif
      Board_LORA_NVIC_Init(Lora_irq_handler);
    board_configure();
@@ -336,144 +352,73 @@
{
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
}

void uart0_receive_callback(void *dev, uint32_t err_code)
{
    uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
}
uint8_t bat_percent;
uint8_t  stationary_flag;
extern uint8_t send_flag;
extern uint8_t txdone;
void mcu_deep_sleep(void)
{
            uint32_t lock;
            trace_flush();
	
            lock = int_lock();
                     sleep_timer_stop();	
            power_enter_power_down_mode(1);
            int_unlock(lock);
}
uint8_t result11;
int main(void)
{		
{		  
   // Initialize MCU system
    board_init();
    // Disable watchdog timer
    wdt_close(WDT_ID0);
    LOG_INFO(TRACE_MODULE_APP, "UCI FiRa example\r\n");
   if(gpio_pin_get_val(MODE_CHANGE_PIN))
   {
   
		
      // Platform init for WSF
    PalSysInit();

    // Initialize os

    //
    // Set up timers for the WSF scheduler.
    //
    WsfOsInit();
    WsfTimerInit();
    sys_tick_callback_set(WsfTimerUpdateTicks);

    //
    // Initialize a buffer pool for WSF dynamic memory needs.
    //
    uint32_t wsfBufMemLen = WsfBufInit(WSF_BUF_POOLS, poolDescriptors);

    if (wsfBufMemLen > FREE_MEM_SIZE)
    {
        LOG_INFO(TRACE_MODULE_APP, "Memory pool is not enough %d\r\n", wsfBufMemLen - FREE_MEM_SIZE);
    }
//
    // Create app task
    //
   wsfHandlerId_t handlerId = WsfOsSetNextHandler(app_handler);
    app_init(handlerId);

    //
    // Create ranging task or test task
    //
    handlerId = WsfOsSetNextHandler(ranging_handler);
    ranging_init(handlerId);

#ifdef UWB_UCI_TEST_EN
    // Create test task
    handlerId = WsfOsSetNextHandler(uwb_test_handler);
    uwb_test_init(handlerId);
#endif

#ifndef MY_MODE
    uwb_open();

    // set advanced parameters
    struct PHY_ADV_CONFIG_T adv_config =
    {
        // RPM0: 40, RPM3: 60
        .thres_fap_detect = 60,
        // RPM0: 4, RPM3: 8
        .nth_scale_factor = 8,
        // RFrame SP0: 0/1, Others: 0/1/2/3
        .ranging_performance_mode = 3,
#if RX_ANT_PORTS_NUM == 4
        .skip_weakest_port_en = 1,
#else
        .skip_weakest_port_en = 0,
#endif
    };
    phy_adv_params_configure(&adv_config);

    // which RX ports will be used for AoA/PDoA
    phy_rx_ant_mode_set(RX_ANT_PORTS_COMBINATION);

    uwbs_init();
    uwb_app_config.ranging_flow_mode = (uint8_t)(RANGING_FLOW_FIRA);
    uwb_app_config.filter_en = (uint8_t)(FILTER_EN);
    uwb_app_config.session_param.tx_power_level = board_param.tx_power_fcc[CALIB_CH(uwb_app_config.ppdu_params.ch_num)];
    uwb_app_config.ppdu_params.rx_ant_id = (uint8_t)(RX_MAIN_ANT_PORT);
	
#elif defined MY_MODE
      Uwb_init();//默认为我们测距配置
      OpenUWB();
      uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
#endif
    //
    // Create UCI transmission layer task
    //
    handlerId = WsfOsSetNextHandler(uci_tl_handler);
    uci_tl_init(handlerId);

    // Initialize low power mode
    power_init();
#if LOW_POWER_EN
    power_mode_request(POWER_UNIT_USER, POWER_MODE_POWER_DOWN);
    uwb_app_config.low_power_en = 1;
#else
    power_mode_request(POWER_UNIT_USER, POWER_MODE_SLEEP);
    uwb_app_config.low_power_en = 0;
#endif

    // Enable sleep timer
    sleep_timer_open(true, SLEEP_TIMER_MODE_ONESHOT, sleep_timer_callback);
		
    while (1)
    {
        wsfOsDispatcher();
#ifdef MY_MODE
            if(normal_flag)
            {
            IdleTask();
            }
#endif
        power_manage();
    }
   }else{
//             adc_open(&usr_adc_cfg);
      LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_lora升级模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
      uart0_Init_normal();
      Lora_1268_Init();
      SwitchLoraSettings(478,7,22);
      Uwb_init();//默认为我们测距配置
      OpenUWB();
       //LOG_INFO(TRACE_MODULE_APP," 切换6\r\n");
      SwitchLoraSettings(0x1f4,7,22);
//      Uwb_init();//默认为我们测距配置
//      OpenUWB();
      uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
    power_init();
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback_normal);
      sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
          while (1)
            {
            uwb_app_poll();//我们的测距逻辑
               Lora_Tx_Poll();
					
            if(flag_secondtask)
      uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
        power_init();
        uint16_t tmp = 0xFFFF;
        result11 = flash_open(FLASH_ID0,NULL);
        if(!result11)
        {
            flag_secondtask = 0;
            SecondTask();
        LOG_INFO(TRACE_MODULE_APP," 打开flash成功\r\n");
        }
            IdleTask();
            }
        result11 = flash_erase(FLASH_ID0, APP_CONFIG_IAPFLAG_SECTOR_ADDR, FLASH_SECTOR_SIZE);//擦除APPFLAG
        if(!result11)
        {
        LOG_INFO(TRACE_MODULE_APP," 擦除标志位成功\r\n");
        }
        result11 = flash_write_nbytes(FLASH_ID0,APP_CONFIG_IAPFLAG_MAP,(uint8_t*)&tmp,2);
        if(!result11)
        {
        LOG_INFO(TRACE_MODULE_APP," 写入标志位FFFF成功\r\n");
        }
        delay_ms(100);
        sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback_normal);
      sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
        while (1)
        {
//            uwb_app_poll();//我们的测距逻辑
//            if(flag_secondtask)
//            {
//            flag_secondtask = 0;
//            SecondTask();
//                    //Lora_Tx_Poll();
//            }
//            Lora_Tx_Poll();	
            LoraUp_Poll();//网关升级
            IdleTask();
        }
   }    

}