PCA的INT脚加速度计清0判断成功，INT脚中断正常

chen

2024-12-11 ac55307242da6846c2b8fe4b710fb90feaa30978

 keil/include/main/main.c

@@ -61,8 +61,9 @@
#include "HIDO_ATLite.h"
#include "HIDO_Timer.h"
#include "TCPClient.h"
#include "PCA9555.h"

//#define DEBUG_MODE
#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
#define TEST_UART_POLL_MODE 0
@@ -98,6 +99,11 @@
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1;  //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
extern uint8_t pca9555writedata_config[10];//暂存寄存器所有配置的数组
extern uint8_t pca9555writedata_output[10];//暂存输出高低电平配置的数组
extern uint8_t pca9555writedata_input[10];//暂存输入寄存器所有配置的数组
extern uint8_t pca9555writedata_polarity[10];//暂存输入极性反转寄存器所有配置的数组
uint8_t temp_pca9555writedata_input[10];//暂存上一次输入寄存器所有配置的数组
typedef enum
{      UN_BIND=0,
        LINK_SUCCESS,
@@ -191,6 +197,7 @@
            }else{
               power_low_flag=0;
               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
      gpio_pin_set(ADC_GND_ENABLE);//在拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
@@ -207,6 +214,7 @@
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2;
extern uint32_t get_in_num,get_out_num;
void MotorPoll(void)
{
    if(UWB_work_state==UN_BIND) {
@@ -320,35 +328,40 @@
        second_count = 0;
        MinuteTask();
    }
      if(!power_low_flag)
      Gps_change();
      else{
      gps_power_state=0;//关闭GPS
      update_led_power_state();
      //初始化GPS计数数据
      gps_need_data_flag=1;
      gps_wait_count2=0;
      gps_wait_count=0;
      }
    //UWB状态检测
      TagListUpdate_person_num_car();
      in_table_log();
		
//      if(!power_low_flag)
//      Gps_change();
//      else{
//      gps_power_state=0;//关闭GPS
//      update_led_power_state();
//      //初始化GPS计数数据
//      gps_need_data_flag=1;
//      gps_wait_count2=0;
//      gps_wait_count=0;
//      }
//    //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
//   {
//    if(IfTCPConnected())
//    {
//        TCP_reconnect_timer =0;
//        flag_TCP_reconnectting = 0;
//    } else {
//        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
//        {
//            flag_TCP_reconnectting = 1;
//        } else {
//            flag_TCP_reconnectting = 0;
//        }
//        if(TCP_reconnect_timer++>600)
//        {
//            TCP_reconnect_timer = 0;
//        }

    if(IfTCPConnected())
    {
        TCP_reconnect_timer =0;
        flag_TCP_reconnectting = 0;
    } else {
        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
        {
            flag_TCP_reconnectting = 1;
        } else {
            flag_TCP_reconnectting = 0;
        }
        if(TCP_reconnect_timer++>600)
        {
            TCP_reconnect_timer = 0;
        }

    }
//    }
//   }
    HIDO_TimerTick();
      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
    nomove_count++;
@@ -359,14 +372,24 @@
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
void check_input_change(void)
{
   uint16_t gpio_state;
   gpio_state=(uint16_t)pca9555writedata_input[0]<<8|pca9555writedata_input[1];
   if(WAKE_UP_POSITION&gpio_state)
   {
      nomove_count=0;
   }
}
static void sleep_timer_callback(void *dev, uint32_t time)
{
    IO_control_init();
    //IO_control_init();
      if(enbale_blink_flag)
   {
   green_charge_state=0;
   charge_red_on();
   }
	 
   charge_state_change();//充电状态判断
if(secondtask_count++%2==0)
    {
@@ -376,7 +399,7 @@
    }
      if(enbale_blink_flag)
   {
      delay_us(5000);
      //delay_us(5000);
   green_charge_state=0;
   charge_red_off();
   }      
@@ -392,6 +415,11 @@
static void move_handler(enum IO_PIN_T pin)
{
    nomove_count=0;
}
static void pca_handler(enum IO_PIN_T pin)
{
   PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
   check_input_change();
}
uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
@@ -440,9 +468,9 @@
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|10;
    g_com_map[VERSION] = (1<<8)|0;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-4G车载手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}

@@ -450,32 +478,32 @@

void IdleTask(void)
{
    if(gpio_pin_get_val(INPUT_5V_Pin))
    {
//    if(gpio_pin_get_val(INPUT_5V_Pin))
//    {

        if(state5v==0)
        {
            state5v=1;
            state5V_prase_flag=state5v;
            gps_prase_flag=0;//解除gps解析
            uart1_change_from_gps_to_debug();//测试
         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartInit();
        }
//        if(state5v==0)
//        {
//            state5v=1;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=0;//解除gps解析
//            uart1_change_from_gps_to_debug();//测试
//         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartInit();
//        }

        //UART_CheckSend();
    } else {
        if(state5v==1)
        {
            g_com_map[MODBUS_MODE] = 0;
            state5v=0;
            state5V_prase_flag=state5v;
            gps_prase_flag=1;//恢复gps解析
            uart1_change_from_debug_to_gps();//测试
          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartDeinit();
        }
    }
//        //UART_CheckSend();
//    } else {
//        if(state5v==1)
//        {
//            g_com_map[MODBUS_MODE] = 0;
//            state5v=0;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=1;//恢复gps解析
//            uart1_change_from_debug_to_gps();//测试
//          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartDeinit();
//        }
//    }
      UART_CheckReceive();
}
int bind_check(void)
@@ -523,7 +551,7 @@
    board_clock_run();
    boot_deinit();
    board_pins_config();
    board_debug_console_open(TRACE_PORT_UART1);
   board_debug_console_open(TRACE_PORT_UART1);
    // Reset reason
    reset_cause_get();
    reset_cause_clear();
@@ -554,8 +582,8 @@

    // TODO 4G
    Uart_Register(UART_ID_4G, UART_ID0);
    Internet_Init();
    TCPClient_Init();
//    Internet_Init();
//    TCPClient_Init();

    gpio_open();
      board_output_init();//配置adcGND引脚
@@ -566,17 +594,17 @@
      
    IIC2_Init();
    Accelerometer_Init();
    IO_control_init();
    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
      PCA9555_init();
    //IO_control_init();
//    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
//    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
//    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
    //gps_air780_power_change(0,1);//开启gps，4G 
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
      gpio_pin_clr(ADC_GND_ENABLE);
   
         Program_Init();
    //uart_open(UART_ID1, &test_uart_cfg);
 
   // uart1_change_from_gps_to_debug();   
    //Uart1GpsRecDebugSend();   
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
@@ -585,50 +613,51 @@
    power_init();
      //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
    sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    //sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
 //   board_5V_input_init(voltage_input_handler);
       adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    board_acceleration_detection_init(move_handler);
//       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
      board_4GUsart_detection_init(_4gUsart_handler);
      pca_input_detection_init(pca_handler);//pca检测输入
      //       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
      //board_4GUsart_detection_init(_4gUsart_handler);
    while (1)
    { test4=gpio_pin_get_val(SCL_PIN);
		
         if(!power_low_flag)//确认是否休眠下才开启功能
         {
        if(flag_TCP_reconnectting||IfTCPConnected())
        {
        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
           
//            if(flag_4guart_needinit)
         //UWBPoll();
//         if(!power_low_flag)//确认是否休眠下才开启功能
//         {
//        if(flag_TCP_reconnectting||IfTCPConnected())
//        {
//        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
//           
////            if(flag_4guart_needinit)
////            {
////                flag_4guart_needinit = 0;
////                AIR780EUartInit();
////            }//yuan
//                 if(flag_4G_recdata==1)
//            {
//                flag_4guart_needinit = 0;
//                AIR780EUartInit();
//            }//yuan
                 if(flag_4G_recdata==1)
            {
                flag_4G_recdata = 2;
               
                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
                Socket_RecvAll();
            }
//                  air780_led_on();
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();
//            air780_led_off();
        }
      }
//                flag_4G_recdata = 2;
//               
//                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
//                Socket_RecvAll();
//            }
////                  air780_led_on();
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
////            air780_led_off();
//        }
//      }
        if(flag_secondtask)
        {
            flag_secondtask = 0;
            SecondTask();
               
        }
            UserKeyTask();
            IMUTask();
//            UserKeyTask();
//            IMUTask();
        IdleTask();
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
@@ -652,7 +681,7 @@
//        }//yuan

            if(delaysleep_count==0)
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected()))) 
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
        {
//               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
            uint32_t lock;