初步解决按钮第二行到第四行没法相应的问题

chen

2025-03-03 b12f7e7c1514077ab1ac4a66b1b2cea8f3c21a56

 keil/include/main/main.c

@@ -62,7 +62,7 @@
#include "HIDO_Timer.h"
#include "TCPClient.h"

//#define DEBUG_MODE
#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
#define TEST_UART_POLL_MODE 0
@@ -76,7 +76,22 @@
#define WARING_LIMIT_TIME 10
#define UPDATE_TIME 10


#define GREEN 1
#define UP_TOWARD 2
#define DOWN_TOWARD 3
#define RED 4
#define BRT 5
#define SAVE 6
#define STEP 7
#define SCAN 8
#define WIN 9
#define TXP 10
#define SFT_D 11
#define O 12
#define VOX 13
#define SQL 14
#define ROGER 15
#define KEY 16
extern uint8_t mUsartReceivePack[100];
extern uint8_t mUsart2ReceivePack[150];
extern uint8_t state5V_prase_flag,gps_prase_flag;
@@ -90,13 +105,14 @@
int16_t fVoltage_mv,first_search_flag;
uint8_t bat_percent,g_start_send_flag=1;
uint8_t link_success_flag,motor_count;
uint16_t gps_wait_count;
uint16_t gps_wait_count,gps_wait_count2;
uint8_t state5v = 1;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,chaging_state,changed_state,air780_success_state,first_motor_in_flag;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,red_charge_state,green_charge_state,air780_success_state,first_motor_in_flag;
float nomove_count=0;
static uint32_t sample[NUM_SAMPLES] = {0};
uint8_t recev_error_num,send_messgae_count,send_flag,control_state;
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1;  //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
typedef enum
{      UN_BIND=0,
        LINK_SUCCESS,
@@ -106,7 +122,7 @@


Commend_SendDate send_struct;
static struct ADC_CFG_T usr_adc_cfg = {
struct ADC_CFG_T usr_adc_cfg = {
    .mode = ADC_MODE_CONTINUE,    /* Selected single conversion mode  */
    .clk_sel = ADC_CLK_HIGH,      /* Selected 62.4M high speed clock */
    .vref_sel = ADC_SEL_VREF_INT, /* Using internal reference voltage (1.2V)*/
@@ -146,6 +162,20 @@
{
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
}
void mcu_deep_sleep(void)
{
            uint32_t lock;
            trace_flush();
            lock = int_lock();
                  LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  gps_air780_power_change(0,0);//关闭gps，4G 
                     sleep_timer_stop();	
                  //adc_close();
            power_enter_power_down_mode(1);
                  //LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
                  sys_reset(0);
            int_unlock(lock);
}
static void adc_callback(void *data, uint32_t number)
{
    uint32_t *result = (uint32_t *)data;
@@ -168,6 +198,17 @@
            bat_percent = ((fVoltage_mv - 3300) /8);
        }
    }
            if(fVoltage_mv<3300)
            {
               power_low_flag=1;
//               gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G 
               LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
            }else{
               power_low_flag=0;
//               gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
               LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
            }
//      gpio_pin_set(ADC_GND_ENABLE);//在拉高
  //  LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
//void UartInit(void)
@@ -177,125 +218,125 @@
//board_debug_console_open(TRACE_PORT_UART0);
//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//}
extern uint8_t gps_uwb_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag;
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2;
extern int16_t beepontime;
extern uint8_t beep_start_flag;
void MotorPoll(void)
{
    if(UWB_work_state==UN_BIND) {
        gps_uwb_flag=0;//关闭GPS
        moter_open_uwb_flag=0;//关闭震动
        need_open_gps_count=0;//清0计数gps
    } else { //绑定状态下
        if(anchordata_num==1) {
            if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
                if(flag_alam_state)
                {
                    flag_alam_state = 0;
                    _4GAlarmUpload(2);
                }
                need_open_gps_count=0;
                moter_open_uwb_flag=0;//关闭震动
                gps_uwb_flag=0;//关闭GPS
            } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                        _4GAlarmUpload(1);
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
                need_open_gps_count++;
                moter_open_uwb_flag=1;//开启震动
                if(need_open_gps_count>=20) {
                    if(!flag_alam_state)
                    {
                        flag_alam_state = 1;
                        _4GAlarmUpload(1);
                    }
                    gps_uwb_flag=1;//开启gps测距流程
                    need_open_gps_count=0;
                }
            }
        } else if(anchordata_num==0) {
            if(!flag_alam_state)
            {
                flag_alam_state = 1;
                _4GAlarmUpload(1);
            }
            distance = -1;
            gps_uwb_flag=1;//开启gps测距流程
            moter_open_uwb_flag=1;//开启震动
            need_open_gps_count=0;
        }
    }
   if(beep_start_flag)
   {
      if(beepontime-->0)
      {
      motor_power_state=0;
      }else{
      beep_start_flag=0;
      motor_power_state=1;
      }
   }
}
void IMUTask(void)
{
//   if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
//   {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
//      mcu_deep_sleep();
//   }
}
void UserKeyTask(void)
 {
//     if(!GET_USERKEY)
//     {
//        if(HIDO_TimerGetTick() - keystarttime>3)
//        {
//            userkey_state = 1;
//            keystarttime =  HIDO_TimerGetTick();
//                  //UDPClient_UploadGPS();
//        }
//        if(HIDO_TimerGetTick() - keystarttime2>10)
//        {
//            g_com_map[CNT_RESTART] = 1;
//        }
//     }else
//     {
//       keystarttime =  HIDO_TimerGetTick(); 
//       keystarttime2 =  HIDO_TimerGetTick(); 
//     }
 } 
void MinuteTask(void)
{
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
//{      gpio_pin_clr(ADC_GND_ENABLE);//拉低
//    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
uint8_t link_error_time;
void SecondTask(void)
{static uint8_t second_count;
{
   static uint8_t second_count;
    if(second_count++>60)
    {
        second_count = 0;
        MinuteTask();
    }
    //UWB更新列表
    TagListUpdate();
    //GPS_Poll();
      GPS_Poll_1h();
    //UWB状态检测
//      if(!power_low_flag)
//      {Gps_change();
//      MotorPoll();
//      }else{
//      gps_power_state=0;//关闭GPS
//      update_led_power_state();
//      //初始化GPS计数数据
//      gps_need_data_flag=1;
//      gps_wait_count2=0;
//      gps_wait_count=0;
//      }
		
//    //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
//   {
//    if(IfTCPConnected())
//    {
////            link_error_time=0;
//        TCP_reconnect_timer =0;
//        flag_TCP_reconnectting = 0;
//    } else {
//        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
//        {
//            flag_TCP_reconnectting = 1;
//        } else {
//               //flag_TCP_reconnectting = 0;
//            sys_reset(4);//重连不上就复位
//        }
//        if(TCP_reconnect_timer++>600)
//        {
//            TCP_reconnect_timer = 0;
//        }

    if(IfTCPConnected())
    {
        TCP_reconnect_timer =0;
        flag_TCP_reconnectting = 0;
    } else {
        if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
        {
            flag_TCP_reconnectting = 1;
        } else {
            flag_TCP_reconnectting = 0;
        }
        if(TCP_reconnect_timer++>600)
        {
            TCP_reconnect_timer = 0;
        }

    }
    HIDO_TimerTick();
    nomove_count++;
//    }
//   }
//    HIDO_TimerTick();
//      if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
//    nomove_count++;
//      else{
//      nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
//      }
}
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,delaysleep_count;
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
static void sleep_timer_callback(void *dev, uint32_t time)
{
    IO_control_init();
  //  UWBPoll();
    
    
    //MotorPoll();

    if(secondtask_count++%2==0)
if(secondtask_count++%2==0)
    {
        flag_secondtask = 1;
    }else{
        flag_secondtask = 0;
    }

    flag_sleeptimer = 1;

    if(delaysleep_count>0)
        delaysleep_count--;
 if(delaysleep_count>0)
     delaysleep_count--;
    //GPS工作逻辑

}

static void voltage_input_handler(enum IO_PIN_T pin)
{

@@ -304,27 +345,24 @@
{
    nomove_count=0;
}
uint8_t flag_4G_recdata,flag_entersleep;
uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
{
   // if(!gpio_pin_get_val(_4G_USART_RX_Pin))
    {
        LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
     //LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
        flag_4G_recdata = 1;
        delaysleep_count = 3;
    }
    
   
}
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
uint8_t bat_bercent_hex; 
void Program_Init(void)
{
    Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
    parameter_init_anchor();//g_com_map表初始化角色默认为基站
    dev_id=g_com_map[DEV_ID];//这里不太对
    group_id=g_com_map[GROUP_ID];//组ID
    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
//    tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
    memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
//    g_com_map[ALARM_DISTANCE1] = 40;
//    g_com_map[ALARM_DISTANCE2] = 40;
@@ -335,78 +373,270 @@
    memcpy(&send_struct.gunLableId,&g_com_map[BIND_DEV_ID],2);//更新绑定ID
    send_struct.tagId=dev_id;//更新设备ID

    if(g_com_map[BIND_DEV_ID]==0)
    {
        UWB_work_state = UN_BIND;
    }else{
        UWB_work_state = SEARCH_DEV;
    }
    if(g_com_map[SEND_4G_SECOND]<60)
        g_com_map[SEND_4G_SECOND]=60;
//    if(g_com_map[BIND_DEV_ID]==0)
//    {
//        UWB_work_state = UN_BIND;
//    }else{
//        UWB_work_state = SEARCH_DEV;
//    }
      //g_com_map[SEND_4G_SECOND]
//    if(g_com_map[SEND_4G_SECOND]<30)
//      {
//      gps_open_flag=0;
//      }else{
//      gps_open_flag=1;
//      }
    g_com_map[MODBUS_MODE] = 0;
      log_4g_enable_flag=g_com_map[LOG_4G_ENABLE];
    ip0 = (g_com_map[TCP_IP_0]>>12&0xf)*1000+(g_com_map[TCP_IP_0]>>8&0xf)*100+(g_com_map[TCP_IP_0]>>4&0xf)*10+(g_com_map[TCP_IP_0]&0xf);
    ip1 = (g_com_map[TCP_IP_1]>>12&0xf)*1000+(g_com_map[TCP_IP_1]>>8&0xf)*100+(g_com_map[TCP_IP_1]>>4&0xf)*10+(g_com_map[TCP_IP_1]&0xf);
    ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
    ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
    port = g_com_map[TCP_PORT];
    g_com_map[VERSION] = (1<<8)|6;
    g_com_map[VERSION] = (1<<8)|0;
    LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-4G手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_对讲机 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
    LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}



uint8_t key_num;
 void board_key_scan(uint8_t *key)
 {
    uint8_t key_down_flag=0;
   //第一行拉低做检测
    gpio_pin_clr(CN1);
    gpio_pin_set(CN2);
    gpio_pin_set(CN3);
    gpio_pin_set(CN4);
    if(!gpio_pin_get_val(COM1)||!gpio_pin_get_val(COM2)||!gpio_pin_get_val(COM3)||!gpio_pin_get_val(COM4))
    {
    if(!gpio_pin_get_val(COM1))
    {
    key_down_flag=1;
    *key=GREEN; 
       while(!gpio_pin_get_val(COM1));
    }else if(!gpio_pin_get_val(COM2))
    {
    key_down_flag=1;
    *key=UP_TOWARD; 
       while(!gpio_pin_get_val(COM2));
    }else if (!gpio_pin_get_val(COM3))
    {
    key_down_flag=1;
    *key=DOWN_TOWARD; 
       while(!gpio_pin_get_val(COM3));
    }else if (!gpio_pin_get_val(COM4))
    {
    key_down_flag=1;
    *key=RED; 
      while(!gpio_pin_get_val(COM4));
    }else{
    key_down_flag=0;
    gpio_pin_set(CN1);
    gpio_pin_set(CN2);
    gpio_pin_set(CN3);
    gpio_pin_set(CN4); 
    }
   }
       //第二行拉低做检测
    gpio_pin_set(CN1);
    gpio_pin_clr(CN2);
    gpio_pin_set(CN3);
    gpio_pin_set(CN4);
   if(!gpio_pin_get_val(COM1)||!gpio_pin_get_val(COM2)||!gpio_pin_get_val(COM3)||!gpio_pin_get_val(COM4))
    {
        if(!gpio_pin_get_val(COM1))
    {
    key_down_flag=1;
    *key=BRT; 
       while(!gpio_pin_get_val(COM1));
    }else if(!gpio_pin_get_val(COM2))
    {
    key_down_flag=1;
    *key=SAVE; 
       while(!gpio_pin_get_val(COM2));
    }else if (!gpio_pin_get_val(COM3))
    {
    key_down_flag=1;
    *key=STEP; 
       while(!gpio_pin_get_val(COM3));
    }else if (!gpio_pin_get_val(COM4))
    {
    key_down_flag=1;
    *key=SCAN; 
      while(!gpio_pin_get_val(COM4));
    }else{
    key_down_flag=0;
    gpio_pin_set(CN1);
    gpio_pin_set(CN2);
    gpio_pin_set(CN3);
    gpio_pin_set(CN4); 
    }
 }
	 
           //第三行拉低做检测
    gpio_pin_set(CN1);
    gpio_pin_set(CN2);
    gpio_pin_clr(CN3);
    gpio_pin_set(CN4);
 if(!gpio_pin_get_val(COM1)||!gpio_pin_get_val(COM2)||!gpio_pin_get_val(COM3)||!gpio_pin_get_val(COM4))
    {
    if(!gpio_pin_get_val(COM1))
    {
    key_down_flag=1;
    *key=WIN; 
       while(!gpio_pin_get_val(COM1));
    }else if(!gpio_pin_get_val(COM2))
    {
    key_down_flag=1;
    *key=TXP; 
       while(!gpio_pin_get_val(COM2));
    }else if (!gpio_pin_get_val(COM3))
    {
    key_down_flag=1;
    *key=SFT_D; 
       while(!gpio_pin_get_val(COM3));
    }else if (!gpio_pin_get_val(COM4))
    {
    key_down_flag=1;
    *key=O; 
      while(!gpio_pin_get_val(COM4));
    }else{
    key_down_flag=0;
    gpio_pin_set(CN1);
    gpio_pin_set(CN2);
    gpio_pin_set(CN3);
    gpio_pin_set(CN4); 
    }
   }
       //第四行拉低做检测
    gpio_pin_set(CN1);
    gpio_pin_set(CN2);
    gpio_pin_set(CN3);
    gpio_pin_clr(CN4);
   if(!gpio_pin_get_val(COM1)||!gpio_pin_get_val(COM2)||!gpio_pin_get_val(COM3)||!gpio_pin_get_val(COM4))
    {
    if(!gpio_pin_get_val(COM1))
    {
    key_down_flag=1;
    *key=VOX; 
       while(!gpio_pin_get_val(COM1));
    }else if(!gpio_pin_get_val(COM2))
    {
    key_down_flag=1;
    *key=SQL; 
       while(!gpio_pin_get_val(COM2));
    }else if (!gpio_pin_get_val(COM3))
    {
    key_down_flag=1;
    *key=ROGER; 
       while(!gpio_pin_get_val(COM3));
    }else if (!gpio_pin_get_val(COM4))
    {
    key_down_flag=1;
    *key=KEY; 
      while(!gpio_pin_get_val(COM4));
    }else{
    key_down_flag=0;
    gpio_pin_set(CN1);
    gpio_pin_set(CN2);
    gpio_pin_set(CN3);
    gpio_pin_set(CN4); 
    }
    }
 }
 
void board_key_message(uint8_t *key)
{
   switch(*key){
      case 0:
			
      break;
      case 1:
			
      break;
		
      case 2:
		
      break;
		
      case 3:
		
      break;
      case 4:
		
      break;
      case 5:
		
      break;
      case 6:
		
      break;
      case 7:
		
      break;
      case 8:
		
      break;
      case 9:
		
      break;
      case 10:
		
      break;
      case 11:
		
      break;
      case 12:
		
      break;
      case 13:
		
      break;
      case 14:
		
      break;
      case 15:
		
      break;
      case 16:
		
      break;
}
										
}
void IdleTask(void)
{
    if(gpio_pin_get_val(INPUT_5V_Pin))
    {
//    if(gpio_pin_get_val(INPUT_5V_Pin))
//    {

        if(state5v==0)
        {
            state5v=1;
            state5V_prase_flag=state5v;
            gps_prase_flag=0;//解除gps解析
            uart1_change_from_gps_to_debug();
         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartInit();
        }
//        if(state5v==0)
//        {
//            state5v=1;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=0;//解除gps解析
//            uart1_change_from_gps_to_debug();//测试
//         //   uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartInit();
//        }

        //UART_CheckSend();
    } else {
        if(state5v==1)
        {
            g_com_map[MODBUS_MODE] = 0;
            state5v=0;
            state5V_prase_flag=state5v;
            gps_prase_flag=1;//恢复gps解析
            uart1_change_from_debug_to_gps();
          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
            //UartDeinit();
        }
    }
//        //UART_CheckSend();
//    } else {
//        if(state5v==1)
//        {
//            g_com_map[MODBUS_MODE] = 0;
//            state5v=0;
//            state5V_prase_flag=state5v;
//            gps_prase_flag=1;//恢复gps解析
//            uart1_change_from_debug_to_gps();//测试
//          //  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
//            //UartDeinit();
//        }
//    }
      board_key_scan(&key_num);
      board_key_message(&key_num);
      UART_CheckReceive();
}
int bind_check(void)
{
    if(g_com_map[BIND_DEV_ID]!=0x00)
    {
        return 1;
//绑定信息为1说明设备已经被下发绑定
    } else {
        return 0;
//绑定信息为0说明设备未被绑定
    }
}
void check_if_in_search(void)
{
    if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
        UWB_work_state=LINK_SUCCESS;
    } else { //否则进入搜索模式
        UWB_work_state=SEARCH_DEV;
        if(first_search_flag==0)
            first_search_flag=1;
    }
}
void boot_deinit(void)
{
@@ -420,13 +650,32 @@
    uart_close(UART_ID1);//解绑原来串口1
    uart_close(UART_ID0);//解绑原来串口0
}
uint8_t flag_4guart_needinit=0,tt2;
uint8_t flag_4guart_needinit=0;
uint8_t index1,index2,index3;
int16_t Voltage_input;
int tt2;
int test1,test3;
uint32_t test4;
uint32_t time_count;

static void app_wdt_callback(void *dev, uint32_t status)
{
    ASSERT(status, "WDT TIMEOUT，程序复位");
      //LOG_INFO(TRACE_MODULE_APP, "程序卡死，看门狗复位");
}
 struct WDT_CFG_T app_wdt_cfg = {
        .timeout = 32768 * 30,
        .rst_en = true,
        .int_en = true,
        .callback = app_wdt_callback,
    };
 
int main(void)
{
    board_clock_run();
    boot_deinit();
    board_pins_config();
    board_debug_console_open(TRACE_PORT_UART1);
    board_debug_console_open(TRACE_PORT_UART0);//4G串口
    // Reset reason
    reset_cause_get();
    reset_cause_clear();
@@ -450,95 +699,124 @@

    // Disable watchdog timer
    wdt_close(WDT_ID0);

    LOG_INFO(TRACE_MODULE_APP, "UWB simple example\r\n");

    // open system timer
    //sys_timer_open();

    // TODO 4G
    Uart_Register(UART_ID_4G, UART_ID0);
    Internet_Init();
    TCPClient_Init();

    gpio_open();
    //board_led_init();

    adc_open(&usr_adc_cfg);
    IIC2_Init();
    Accelerometer_Init();
    IO_control_init();
    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_OUT, 0);
    io_pull_set(SCL_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
    gps_air780_power_change(0,1);//开启gps，4G 
//    adc_open(&usr_adc_cfg);
      board_gpio_init();
//    IIC2_Init();
//    Accelerometer_Init();
//    io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
//    gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
//    io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
    //gps_air780_power_change(0,1);//开启gps，4G 
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
    adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
   
         Program_Init();
    uart_open(UART_ID1, &test_uart_cfg);
    Program_Init();
   // uart1_change_from_gps_to_debug();   
    //Uart1GpsRecDebugSend();   
    uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
   
// Initialize low power mode
    power_init();
      AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
      //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
    sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
    //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
    sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
 //   board_5V_input_init(voltage_input_handler);
    board_acceleration_detection_init(move_handler);
//       adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
    //board_acceleration_detection_init(move_handler);
//       LOG_INFO(TRACE_MODULE_APP, "测试进入app");
    board_4GUsart_detection_init(_4gUsart_handler);
    tt2 = gpio_pin_get_val(_4G_USART_RX_Pin);
      //board_4GUsart_detection_init(_4gUsart_handler);
		
    while (1)
    {
        if(flag_TCP_reconnectting||IfTCPConnected())
        {
            if(flag_4G_recdata==1)
            {
                flag_4G_recdata = 2;
               
                LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll\r\n");
                Socket_RecvAll();
            }
            air780_led_on();
//LOG_INFO(TRACE_MODULE_APP, "处理4G\r\n");
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();
            air780_led_off();
        }
			
//         if(!power_low_flag)//确认是否休眠下才开启功能
//         {
//        if(flag_TCP_reconnectting||IfTCPConnected())
//        {
////               if(flag_TCP_reconnectting)
////               {
////               link_error_time++;
////               }//后加的
//        //    LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
//           
////            if(flag_4guart_needinit)
////            {
////                flag_4guart_needinit = 0;
////                AIR780EUartInit();
////            }//yuan
//                 if(flag_4G_recdata==1)
//            {
//                flag_4G_recdata = 2;
//               
//                //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
//                Socket_RecvAll();
//            }
////                  air780_led_on();
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
////            air780_led_off();
//        }
//      }
        if(flag_secondtask)
        {
            flag_secondtask = 0;
            SecondTask();
            //   time_count++;
        }
            UserKeyTask();
            //IMUTask();
        IdleTask();
 
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
       // if(!gpio_pin_get_val(INPUT_5V_Pin))//AIR780E_IsIPIdle() Socket_IsSendQueueEmpty(0)
      //  if(flag_4G_recdata!=2)
        //if(((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected()))) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
        if(delaysleep_count==0)
        if((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0)))
//        if(!gps_need_data_flag&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&Socket_IsSendQueueEmpty(0))||!flag_TCP_reconnectting&&!IfTCPConnected())) //进入休眠条件（与关系，全满足才进）：1.没有5V输入 2 TCP已连接时发送队列为空||TCP无连接时不在重连状态。
//        {
//                 if(!flag_4guart_needinit)
//            {
//                           LOG_INFO(TRACE_MODULE_APP, "4G RX 中断打开\r\n");
//                             board_4GUsart_detection_init(_4gUsart_handler);

//            }
//               flag_sleeptimer =0;
            //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
//                flag_4guart_needinit = 1;

//        trace_flush();
//        uint32_t lock = int_lock();
//        //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
//        power_enter_power_down_mode(0);
//        int_unlock(lock);
//        }//yuan

            if(delaysleep_count==0)
        if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag)) 
        {
//               test1=gpio_pin_get_val(_4G_USART_RX_Pin);
            uint32_t lock;
            flag_4guart_needinit = 1;
            Internet_Poll();
            HIDO_ATLitePoll();
            HIDO_TimerPoll();
            TCPClient_Poll();
            //flag_4guart_needinit = 1;
//            Internet_Poll();
//            HIDO_ATLitePoll();
//            HIDO_TimerPoll();
//            TCPClient_Poll();
            
         //   power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)_4G_USART_RX_Pin, POWER_WAKEUP_LEVEL_LOW);
            LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
           // delay_us(300000);
            trace_flush();
            lock = int_lock();            
            power_enter_power_down_mode(0);
                  uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
//               test3=gpio_pin_get_val(_4G_USART_RX_Pin);
               //LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
            int_unlock(lock);
        }

#endif
    }
}