V1.0 开发完成 5S一次，实际休眠时间要诚5 上位机设置除以5就行 休眠18ua 功耗

WXK

2025-07-22 e3cc01b77b6f240140d2536e365e559b42d1505c

 keil/uwb_app.c

@@ -116,7 +116,7 @@
    uint8_t phy_work_mode; /* PHY_TX / PHY_RX / PHT_TX|PHY_RX */
    struct UWB_CONFIG_T phy_cfg;
};

extern uint8_t uwb_ch;
static struct mk_uwb_configure config = {
    .phy_work_mode = (uint8_t)(PHY_TX | PHY_RX),
    .phy_cfg.ch_num = 5,                      /* Channel number.                           */
@@ -230,6 +230,8 @@
extern uint16_t mubiao_anchor_ID;
uint8_t Lora_qingqiu_flag;
extern uint16_t Lora_qingqiu_bao;
uint8_t shengji_flag;
extern uint8_t Dtu_shengji_jindu[20];
static void rx_int_callback(struct MAC_HW_REPORT_T *rx_report)
{      uint8_t valid_sts=0;
    uint16_t checksum1 = 0,dest_id;
@@ -251,7 +253,8 @@
        rssi = rx_report->rssi;
        receive_flag=1;
//        uart_send(UART_ID0, rx_buf,rx_length, NULL);
        if(rx_buf[MESSAGE_TYPE_IDX]==MBX_POLL)
        gpio_pin_toggle(IO_PIN_4);
        if(rx_buf[MESSAGE_TYPE_IDX]==MBX_POLL&&!shengji_flag)
        {
        Anchor_App();
        }
@@ -264,6 +267,7 @@
            {
                if(!memcmp(&dev_id,&dest_id,2)/*||dest_id==0xffff||(dest_id==0xfffe&&get_channel==5)*/)
                {
                    shengji_flag=1;
                    switch(rx_buf[MSG_TYPE_IDX])
                    {
                    case LORA_MSGTYPE_UPDATE_CONFIRM:
@@ -285,8 +289,13 @@
                        break;
                    
                    case 0x99:
                    LOG_INFO(TRACE_MODULE_APP, "收到结束升级请求\r\n",Lora_qingqiu_bao);
                        delay_ms(500);
//                    LOG_INFO(TRACE_MODULE_APP, "收到结束升级请求\r\n",Lora_qingqiu_bao);
                    delay_ms(200);
                    Dtu_shengji_jindu[4]=100;
                    memcpy(&Dtu_shengji_jindu[5],&mubiao_anchor_ID,2);
                    uart_send(UART_ID0, Dtu_shengji_jindu,9, NULL);
                    
                        delay_ms(1000);
//                        Lora_upanc_flag=0;
                        Lora_qingqiu_flag=0;
                        NVIC_SystemReset();
@@ -317,7 +326,7 @@
//            }
            }
        }
				

         #ifdef STS_MODE
            valid_sts= sts_valid_check();
      if (valid_sts)
@@ -649,6 +658,33 @@

   if(HIDO_TimerGetTick()-uwbtasktimer >=1)
   {
            
    for(uint16_t i=0;i<taglist_num-1;i++)
    {
        for(uint16_t j=0;j<taglist_num-1-i;j++)
        {
            if(tagdist_list[j]>tagdist_list[j+1])
            {
                uint16_t id,dist,version;
                uint8_t bat;
                id = tagid_list[j];
                dist = tagdist_list[j];
                version = anchordata_version[j];
                tagid_list[j] = tagid_list[j+1];
                tagdist_list[j] = tagdist_list[j+1];
                anchordata_version[j] = anchordata_version[j+1];
                tagid_list[j+1] = id;
                tagdist_list[j+1] = dist;
                anchordata_version[j+1] = version;
            }
        }
    
    }
    
        if(taglist_num>6)
        {
        taglist_num=6;
        }
      uwbtasktimer = HIDO_TimerGetTick();
      UWBOneSecondTask();
        uwbsend[0]=0x55;
@@ -885,6 +921,7 @@
    phy_rx_ant_mode_set(RX_ANT_PORTS_COMBINATION);
   #endif
    // Set calibration parameters
//    config.phy_cfg.ch_num=g_com_map[NEARBASE_ID1];
    uwb_calibration_params_set(config.phy_cfg.ch_num);
   #ifndef STS_MODE
   // set advanced parameters
@@ -899,7 +936,7 @@
    struct PHY_ADV_CONFIG_T adv_config = {
        .thres_fap_detect = 40,
        .nth_scale_factor = 4,
        .ranging_performance_mode = 3,
        .ranging_performance_mode = 0,
        .skip_weakest_port_en = 0,
    };
   #endif
@@ -921,218 +958,243 @@
      #endif
      mac_register_process_handler(tx_int_callback, rx_int_callback);//初始化回调
}
//主函数绑定接受逻辑
int UwbSearch(void)
{
    uint8_t i;
    uint16_t tempid;
    // The following peripherals will be initialized in the uwb_open function
    // phy/mac/aes/lsp/phy timers initialized
    uwb_open();
   #ifdef STS_MODE
  // Set STS key and IV
    phy_sts_key_configure(&sts_iv_key);
	
   // which RX ports will be used for AoA/PDoA
    phy_rx_ant_mode_set(RX_ANT_PORTS_COMBINATION);
   #endif
    // Set calibration parameters
    uwb_calibration_params_set(config.phy_cfg.ch_num);
////主函数绑定接受逻辑
//int UwbSearch(void)
//{
//    uint8_t i;
//    uint16_t tempid;
//    // The following peripherals will be initialized in the uwb_open function
//    // phy/mac/aes/lsp/phy timers initialized
//    uwb_open();
//   #ifdef STS_MODE
//  // Set STS key and IV
//    phy_sts_key_configure(&sts_iv_key);
//	
//   // which RX ports will be used for AoA/PDoA
//    phy_rx_ant_mode_set(RX_ANT_PORTS_COMBINATION);
//   #endif
//    // Set calibration parameters
//    uwb_calibration_params_set(config.phy_cfg.ch_num);

   #ifndef STS_MODE
   // set advanced parameters
    struct PHY_ADV_CONFIG_T adv_config = {
        .thres_fap_detect = 40,
        .nth_scale_factor = 4,
        .ranging_performance_mode = 0,
        .skip_weakest_port_en = 0,
    };
      #else
        // set advanced parameters
    struct PHY_ADV_CONFIG_T adv_config = {
        .thres_fap_detect = 40,
        .nth_scale_factor = 4,
        .ranging_performance_mode = 3,
        .skip_weakest_port_en = 0,
    };
      #endif
    phy_adv_params_configure(&adv_config);
//   #ifndef STS_MODE
//   // set advanced parameters
//    struct PHY_ADV_CONFIG_T adv_config = {
//        .thres_fap_detect = 40,
//        .nth_scale_factor = 4,
//        .ranging_performance_mode = 0,
//        .skip_weakest_port_en = 0,
//    };
//      #else
//        // set advanced parameters
//    struct PHY_ADV_CONFIG_T adv_config = {
//        .thres_fap_detect = 40,
//        .nth_scale_factor = 4,
//        .ranging_performance_mode = 3,
//        .skip_weakest_port_en = 0,
//    };
//      #endif
//    phy_adv_params_configure(&adv_config);

    // uwb configure
    uwb_configure(config.phy_work_mode, board_param.tx_power_fcc[CALIB_CH(config.phy_cfg.ch_num)], &config.phy_cfg);
		
      #ifdef STS_MODE
      ranging_lib_init();
      #endif
    ranging_frame_type_set(config.phy_cfg.sts_pkt_cfg);
		
      #ifdef STS_MODE
      aoa_aux_info_set(AOA_AUX_ANT_IQ_RSSI_PDOA_AOA_FOM);
    aoa_steering_vector_set((const float *)((uint32_t)((config.phy_cfg.ch_num == 9) ? svec_ch9_ptr : svec_ch5_ptr) | SRAM_BASE));
//    // uwb configure
//    uwb_configure(config.phy_work_mode, board_param.tx_power_fcc[CALIB_CH(config.phy_cfg.ch_num)], &config.phy_cfg);
//		
//      #ifdef STS_MODE
//      ranging_lib_init();
//      #endif
//    ranging_frame_type_set(config.phy_cfg.sts_pkt_cfg);
//		
//      #ifdef STS_MODE
//      aoa_aux_info_set(AOA_AUX_ANT_IQ_RSSI_PDOA_AOA_FOM);
//    aoa_steering_vector_set((const float *)((uint32_t)((config.phy_cfg.ch_num == 9) ? svec_ch9_ptr : svec_ch5_ptr) | SRAM_BASE));

    aoa_param_config();
		
      phy_rx_sts_switch_mode_set(config.phy_cfg.sts_pkt_cfg, STS_SWITCH_EVERY_4SYM, 0, 0);
      #endif
    // Register rx interrupt callback function
    mac_register_process_handler(tx_int_callback, rx_int_callback);
		
    receive_flag = 0;
    temp_count3=phy_timer_count_get();
    gpio_pin_set(SCL_PIN);
      sts_lsp_store();
    flag_temp2=uwb_rx(0, 0, RX_SYNC_WIN_US_TEMP);//开启接收
    start_receive_count=phy_timer_count_get();
    poll_timeout=US_TO_PHY_TIMER_COUNT(2000000);//多一个多0.4ms默认0.4ms计算为0.125*4*100000,默认开启1mss
    end_receive_count=start_receive_count+poll_timeout;
    if(end_receive_count>=UINT32_MAX)
    {
        end_receive_count-=UINT32_MAX;
    }
    current_count=phy_timer_count_get();
    while(current_count<end_receive_count||current_count>end_receive_count+HALF_SECOND_TIME)//循环接受包体,若为124.8K则是+62400000
    {
        while(mac_is_busy())
        {
            IdleTask();
            current_count=phy_timer_count_get();
            if(current_count>end_receive_count&&current_count<end_receive_count+HALF_SECOND_TIME)
            {
                    break;
            }
        }
            sts_lsp_store_stop();
				
				
        temp_count2=phy_timer_count_get();
        if(receive_flag==1)//成功接收
        {
//            if(group_id==rx_buf[GROUP_ID_IDX]&&rx_buf[MESSAGE_TYPE_IDX] == MBX_POLL&&!memcmp(&rx_buf[TAG_ID_IDX],&g_com_map[BIND_DEV_ID],2))//判断是否是和自己是同一组通讯的且为poll包
            if(group_id==rx_buf[GROUP_ID_IDX]&&rx_buf[MESSAGE_TYPE_IDX] == MBX_POLL)//判断是否是和自己是同一组通讯的且为poll包
                  {   
                       sleep_timer_start(__MS_TO_32K_CNT(UWB_DELAY_TIME_US-13));//测试
                        range_timeout_us=20000;//将下次range开启后超时时间设为20ms之后再range里恢复
                        temp_count2=phy_timer_count_get();
                frame_seq_nb2 = rx_buf[SEQUENCE_IDX];//获取包序
                battary = rx_buf[BATTARY_IDX];
                rec_nearbase_num=rx_buf[FZ_NEARBASENUM_INDEX];  //标签传过来的他与基站交互的基站id数目
                memcpy(&tag_id_recv,&rx_buf[TAG_ID_IDX],2);
                memcpy(rec_ancidlist,&rx_buf[FZ_NEARBASEID_INDEX],2*rec_nearbase_num);
                memcpy(rec_ancdistlist,&rx_buf[FZ_NEARBASEID_INDEX+2*rec_nearbase_num],2*rec_nearbase_num);
                memcpy(&rec_antdelay,&rx_buf[FZ_NEARBASEID_INDEX+rec_nearbase_num*4],2);
                for(i=0; i<rec_nearbase_num; i++)
                {
                    if(rec_ancidlist[i] == dev_id)
                    {
                                    temp_recdist_before_offset=rec_ancdistlist[i];
                                    rec_ancdistlist[i]+=(int16_t)g_com_map[DIST_OFFSET];
                        PushAnchorDataArray(tag_id_recv,rec_ancdistlist[i],battary);
                    }
                }
                for(i=0; i<rec_nearbase_num; i++)
                {
                    memcpy(&tempid,&rx_buf[FZ_NEARBASEID_INDEX+i*2],2);
                    if(tempid==dev_id)//也是比id如果有就更新没有就抢占
                    {
                        seize_anchor=0;  //非抢占。已存在列表中
                        Anchor_RecNearPoll(i);
                        break;
                    }
                }
//    aoa_param_config();
//		
//      phy_rx_sts_switch_mode_set(config.phy_cfg.sts_pkt_cfg, STS_SWITCH_EVERY_4SYM, 0, 0);
//      #endif
//    // Register rx interrupt callback function
//    mac_register_process_handler(tx_int_callback, rx_int_callback);
//		
//    receive_flag = 0;
//    temp_count3=phy_timer_count_get();
//    gpio_pin_set(SCL_PIN);
//      sts_lsp_store();
//    flag_temp2=uwb_rx(0, 0, RX_SYNC_WIN_US_TEMP);//开启接收
//    start_receive_count=phy_timer_count_get();
//    poll_timeout=US_TO_PHY_TIMER_COUNT(2000000);//多一个多0.4ms默认0.4ms计算为0.125*4*100000,默认开启1mss
//    end_receive_count=start_receive_count+poll_timeout;
//    if(end_receive_count>=UINT32_MAX)
//    {
//        end_receive_count-=UINT32_MAX;
//    }
//    current_count=phy_timer_count_get();
//    while(current_count<end_receive_count||current_count>end_receive_count+HALF_SECOND_TIME)//循环接受包体,若为124.8K则是+62400000
//    {
//        while(mac_is_busy())
//        {
//            IdleTask();
//            current_count=phy_timer_count_get();
//            if(current_count>end_receive_count&&current_count<end_receive_count+HALF_SECOND_TIME)
//            {
//                    break;
//            }
//        }
//            sts_lsp_store_stop();
//				
//				
//        temp_count2=phy_timer_count_get();
//        if(receive_flag==1)//成功接收
//        {
////            if(group_id==rx_buf[GROUP_ID_IDX]&&rx_buf[MESSAGE_TYPE_IDX] == MBX_POLL&&!memcmp(&rx_buf[TAG_ID_IDX],&g_com_map[BIND_DEV_ID],2))//判断是否是和自己是同一组通讯的且为poll包
//            if(group_id==rx_buf[GROUP_ID_IDX]&&rx_buf[MESSAGE_TYPE_IDX] == MBX_POLL)//判断是否是和自己是同一组通讯的且为poll包
//                  {   
//                       sleep_timer_start(__MS_TO_32K_CNT(UWB_DELAY_TIME_US-13));//测试
//                        range_timeout_us=20000;//将下次range开启后超时时间设为20ms之后再range里恢复
//                        temp_count2=phy_timer_count_get();
//                frame_seq_nb2 = rx_buf[SEQUENCE_IDX];//获取包序
//                battary = rx_buf[BATTARY_IDX];
//                rec_nearbase_num=rx_buf[FZ_NEARBASENUM_INDEX];  //标签传过来的他与基站交互的基站id数目
//                memcpy(&tag_id_recv,&rx_buf[TAG_ID_IDX],2);
//                memcpy(rec_ancidlist,&rx_buf[FZ_NEARBASEID_INDEX],2*rec_nearbase_num);
//                memcpy(rec_ancdistlist,&rx_buf[FZ_NEARBASEID_INDEX+2*rec_nearbase_num],2*rec_nearbase_num);
//                memcpy(&rec_antdelay,&rx_buf[FZ_NEARBASEID_INDEX+rec_nearbase_num*4],2);
//                for(i=0; i<rec_nearbase_num; i++)
//                {
//                    if(rec_ancidlist[i] == dev_id)
//                    {
//                                    temp_recdist_before_offset=rec_ancdistlist[i];
//                                    rec_ancdistlist[i]+=(int16_t)g_com_map[DIST_OFFSET];
//                        PushAnchorDataArray(tag_id_recv,rec_ancdistlist[i],battary);
//                    }
//                }
//                for(i=0; i<rec_nearbase_num; i++)
//                {
//                    memcpy(&tempid,&rx_buf[FZ_NEARBASEID_INDEX+i*2],2);
//                    if(tempid==dev_id)//也是比id如果有就更新没有就抢占
//                    {
//                        seize_anchor=0;  //非抢占。已存在列表中
//                        Anchor_RecNearPoll(i);
//                        break;
//                    }
//                }

                if(i==rec_nearbase_num)
                {
                    seize_anchor=1;   //抢占anchor
                    Anchor_RecNearPoll(i);
                }
                
                gpio_pin_clr(SCL_PIN);//测试
                        LOG_INFO(TRACE_MODULE_APP,"标签ID：%X,距离: %d 信号强度ANT0:%f,信号强度ANT2: %f\r\n",g_com_map[BIND_DEV_ID],distance,sts_rssi[0],sts_rssi[2]);
                return 1;//返回发送成功标志
            }
//                if(i==rec_nearbase_num)
//                {
//                    seize_anchor=1;   //抢占anchor
//                    Anchor_RecNearPoll(i);
//                }
//                
//                gpio_pin_clr(SCL_PIN);//测试
//                        LOG_INFO(TRACE_MODULE_APP,"标签ID：%X,距离: %d 信号强度ANT0:%f,信号强度ANT2: %f\r\n",g_com_map[BIND_DEV_ID],distance,sts_rssi[0],sts_rssi[2]);
//                return 1;//返回发送成功标志
//            }

        }
            temp_count3=phy_timer_count_get();
            sts_lsp_store();
        flag_temp2=uwb_rx(0, 0, RX_SYNC_WIN_US_TEMP);//再次开启接收
    }
      delay_us(2);
      sts_lsp_store_stop();
      uwb_rx_force_off(1);
    // LOG_INFO(TRACE_MODULE_APP,"超时定时器：%x,%x,%x\r\n",start_receive_count,end_receive_count,current_count);
    gpio_pin_clr(SCL_PIN);//测试
    return 0;//返回绑定失败标志
}
//        }
//            temp_count3=phy_timer_count_get();
//            sts_lsp_store();
//        flag_temp2=uwb_rx(0, 0, RX_SYNC_WIN_US_TEMP);//再次开启接收
//    }
//      delay_us(2);
//      sts_lsp_store_stop();
//      uwb_rx_force_off(1);
//    // LOG_INFO(TRACE_MODULE_APP,"超时定时器：%x,%x,%x\r\n",start_receive_count,end_receive_count,current_count);
//    gpio_pin_clr(SCL_PIN);//测试
//    return 0;//返回绑定失败标志
//}
//}

#define SEARCH_TIMESTEMP 20
void UWBPoll(void)
{
    switch(UWB_work_state)
    {
    case LINK_SUCCESS:
    {   //连接成功进行轮询测距
//void UWBPoll(void)
//{
//    switch(UWB_work_state)
//    {
//    case LINK_SUCCESS:
//    {   //连接成功进行轮询测距

        uwb_led_on();
        UwbRange();
        uwb_led_off();
//        uwb_led_on();
//        UwbRange();
//        uwb_led_off();

    }
    break;
    case SEARCH_DEV:
    {   
         UWB_work_state=LINK_SUCCESS;
         Uwb_init();
//         //接包不成功或者通讯失败进入搜索模式
//        if(search_open_flag)
//    }
//    break;
//    case SEARCH_DEV:
//    {   
//         UWB_work_state=LINK_SUCCESS;
//         Uwb_init();
////         //接包不成功或者通讯失败进入搜索模式
////        if(search_open_flag)
////        {
////            LOG_INFO(TRACE_MODULE_APP,"开启搜索\r\n");
////            search_open_flag=0;
////            uwb_led_on();
////            link_success_flag=UwbSearch();//第一次开启接收2s绑定失败后则进行下面1分钟后重新开启2s绑定流程
////            uwb_led_off();
////            if(link_success_flag)
////                UWB_work_state=LINK_SUCCESS;
////        }else{
////            LOG_INFO(TRACE_MODULE_APP,"等待进入搜索模式：%d\r\n",SEARCH_TIMESTEMP-uwb_searchcount);
////        }

//    }
//    break;
//    case UN_BIND:
//    {
//        uwb_led_off();//关闭uwb指示灯
//    }
//    break;
//    }
//    if(UWB_work_state==LINK_SUCCESS)
//    {   //成功时清0错误计数
//        uwb_searchcount=0;
//    }
//    if(UWB_work_state==SEARCH_DEV)
//    {
//        if(!search_open_flag)
//        {
//            LOG_INFO(TRACE_MODULE_APP,"开启搜索\r\n");
//            search_open_flag=0;
//            uwb_led_on();
//            link_success_flag=UwbSearch();//第一次开启接收2s绑定失败后则进行下面1分钟后重新开启2s绑定流程
//            uwb_led_off();
//            if(link_success_flag)
//                UWB_work_state=LINK_SUCCESS;
//        }else{
//            LOG_INFO(TRACE_MODULE_APP,"等待进入搜索模式：%d\r\n",SEARCH_TIMESTEMP-uwb_searchcount);
//            if(uwb_searchcount++>SEARCH_TIMESTEMP)
//            {
//                uwb_searchcount=0;
//                search_open_flag=1;
//            }
//        }
//        //link_error_count+=g_com_map[COM_INTERVAL];
//        //if(link_error_count>=g_com_map[4G_INTERNAL])
//        //link_error_count=0;
//       // update_led_power_state();//更新灯状态
//    }
//     //LOG_INFO(TRACE_MODULE_APP,"UWB状态：%d\r\n",UWB_work_state);
//}

    }
    break;
    case UN_BIND:
    {
        uwb_led_off();//关闭uwb指示灯
    }
    break;
    }
    if(UWB_work_state==LINK_SUCCESS)
    {   //成功时清0错误计数
        uwb_searchcount=0;
    }
    if(UWB_work_state==SEARCH_DEV)
    {
        if(!search_open_flag)
        {
            if(uwb_searchcount++>SEARCH_TIMESTEMP)
            {
                uwb_searchcount=0;
                search_open_flag=1;
            }
        }
        //link_error_count+=g_com_map[COM_INTERVAL];
        //if(link_error_count>=g_com_map[4G_INTERNAL])
        //link_error_count=0;
       // update_led_power_state();//更新灯状态
    }
     //LOG_INFO(TRACE_MODULE_APP,"UWB状态：%d\r\n",UWB_work_state);
}

uint8_t GetUWBBindState(void)
//uint8_t GetUWBBindState(void)
//{
//    if(UWB_work_state == UN_BIND)
//    {
//        return 0;
//    }
//    return 1;
//}
void Tag_App(void)//发送模式(TAG标签)
{
    if(UWB_work_state == UN_BIND)
    {
        return 0;
    }
    return 1;
	
   //LED0_ON;
//   SPIx_CS_GPIO->BRR = SPIx_CS;
//   delay_us(700);
//   SPIx_CS_GPIO->BSRR = SPIx_CS;
//   id =  dwt_readdevid() ;
//       while (DWT_DEVICE_ID != id) 
//    {
//      //   Dw1000_Init();
//         id =  dwt_readdevid() ;
//        IdleTask();	
//        if(error_times++>20)
//        {
//            printf("DW ID ERROR.\r\n");
//            SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader   
//        }
//    }
//    error_times = 0;
//    SwitchTagState();
//     userkey_state = !GET_USERKEY;
//   dwt_entersleep();
}