V1.59 测试完成 防撞汇总

zhyinch

2022-01-20 5a0d34ccd87bf08fc9dcce08208c2b5f764fe804

 Ô´Âë/ºËÐÄ°å/Src/application/dw_app.c

@@ -50,7 +50,7 @@
LPFilter_Frac* p_Dis_Filter;      //测距用的低通滤波器
int32_t g_Tagdist[TAG_NUM_IN_SYS];
uint8_t g_flag_Taggetdist[256];

extern u16 supergroupid;
static uint64_t get_tx_timestamp_u64(void)
{
    uint8_t ts_tab[5];
@@ -316,8 +316,8 @@
u8 test=0;
u8 anclost_times=0;
u8 exsistbase_list[MAX_NEARBASE_NUM],report_num,get_newbase=0;
u16 temp_sync_timer1,temp_sync_timer2;

u16 temp_sync_timer1,temp_sync_timer2,rec_extratag_id;
int32_t rec_extratag_dist;
 void NearPoll(void)
{
   static u8 mainbase_lost_count=0,flag_finalsend,flag_rxon;
@@ -399,7 +399,7 @@
                     dwt_readrxdata(rx_buffer, frame_len, 0);   //读取接收数据
                     dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
                     dwt_rxenable(0);//打开接收
                     if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&rx_buffer[GROUP_ID_IDX] == group_id) //判断接收到的数据是否是response数据
                     if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&(rx_buffer[GROUP_ID_IDX]==supergroupid||rx_buffer[GROUP_ID_IDX] == group_id||group_id==supergroupid)) //判断接收到的数据是否是response数据
                     {   u16 rec_nearbaseid,rec_nearbasepos;
                        int32_t temp_dist;
                        poll_tx_ts = get_tx_timestamp_u64();                              //获得POLL发送时间T1
@@ -444,6 +444,9 @@
                           ////////////////////////////
                           rec_nearbasepos=0;
                           
                           memcpy(&rec_extratag_id,&rx_buffer[EXTRA_TAGID_INDEX],2);
                           memcpy(&rec_extratag_dist,&rx_buffer[EXTRA_TAGDIST_INDEX],4);
								
                           memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
                           nearbase_distlist[rec_nearbasepos]=temp_dist;
                        if(temp_dist!=0x1ffff)
@@ -464,7 +467,7 @@
                           dwt_writetxdata(28+nearbase_num*4, tx_nearfinal_msg, 0);//将发送数据写入DW1000
                           dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
                           memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
                        if(temp_dist!=0x1ffff&&g_com_map[ALARM_DISTANCE1] == 1)
                        if(temp_dist!=0x1ffff)
                           {
                              g_Resttimer=0;
                                        IWDG_Feed();
@@ -487,10 +490,28 @@
                              memcpy(&usart_send[19],&checksum,2);
                              UART_PushFrame(usart_send,21);
                              #endif

                           //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
                        //   result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送			
                           //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
                           }
                           if(rec_extratag_dist!=0x1ffff&&rec_extratag_dist!=0&&rx_buffer[GROUP_ID_IDX]!=supergroupid)
                           {
                           #ifdef USART_SINGLE_OUTPUT
                              usart_send[2] = 1;//正常模式
                              usart_send[3] = 17;//数据段长度
                              usart_send[4] = frame_seq_nb;//数据段长度
                              if(g_com_map[DEV_ROLE])
                              {
                              memcpy(&usart_send[5],&rec_extratag_id,2);
                              memcpy(&usart_send[7],&rec_nearbaseid,2);		
                              }else{
                              memcpy(&usart_send[5],&rec_nearbaseid,2);
                              memcpy(&usart_send[7],&rec_extratag_id,2);	
                              }											
                              memcpy(&usart_send[9],&rec_extratag_dist,4);
                              usart_send[13] = battary;
                              usart_send[14] = button;
                              checksum = Checksum_u16(&usart_send[2],17);
                              memcpy(&usart_send[19],&checksum,2);
                              UART_PushFrame(usart_send,21);
                              #endif
                        }
      
                           
@@ -503,7 +524,8 @@
                              nearbaseid_list[rec_nearbasepos] = rec_nearbaseid;
                              memcpy(&tx_nearfinal_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
                           }
									
                          memcpy(&rec_extratag_id,&rx_buffer[EXTRA_TAGID_INDEX],2);
                           memcpy(&rec_extratag_dist,&rx_buffer[EXTRA_TAGDIST_INDEX],4);
                           memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
                           nearbase_distlist[rec_nearbasepos]=temp_dist;
                           
@@ -516,7 +538,7 @@
                           LED0_BLINK;
//                           memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
//                           tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
                           if(temp_dist!=0x1ffff&&g_com_map[ALARM_DISTANCE1] == 1)
                           if(temp_dist!=0x1ffff)
                           {
                              #ifdef USART_SINGLE_OUTPUT
                              usart_send[2] = 1;//正常模式
@@ -541,6 +563,28 @@
                           //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
                        //   result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送         
                           //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
                        }
                           if(rec_extratag_dist!=0x1ffff&&rec_extratag_dist!=0&&rx_buffer[GROUP_ID_IDX]!=supergroupid)
                           {
                           #ifdef USART_SINGLE_OUTPUT
                              usart_send[2] = 1;//正常模式
                              usart_send[3] = 17;//数据段长度
                              usart_send[4] = frame_seq_nb;//数据段长度
                              if(g_com_map[DEV_ROLE])
                              {
                              memcpy(&usart_send[5],&rec_extratag_id,2);
                              memcpy(&usart_send[7],&rec_nearbaseid,2);		
                              }else{
                              memcpy(&usart_send[5],&rec_nearbaseid,2);
                              memcpy(&usart_send[7],&rec_extratag_id,2);	
                              }											
                              memcpy(&usart_send[9],&rec_extratag_dist,4);
                              usart_send[13] = battary;
                              usart_send[14] = button;
                              checksum = Checksum_u16(&usart_send[2],17);
                              memcpy(&usart_send[19],&checksum,2);
                              UART_PushFrame(usart_send,21);
                              #endif
                        }
                     }                           
                     }
@@ -912,8 +956,18 @@
            dwt_writetxdata(22+REMOTEPARA_LEN, tx_nearresp_msg, 0);//写入发送数据
            dwt_writetxfctrl(22+REMOTEPARA_LEN, 0);//设定发送长度      
         }else{
         dwt_writetxdata(22, tx_nearresp_msg, 0);//写入发送数据
         dwt_writetxfctrl(22, 0);//设定发送长度
            if(taglist_pos==1)
            {
               memcpy(&tx_nearresp_msg[EXTRA_TAGID_INDEX], &tagid_list[0], 2);
               memcpy(&tx_nearresp_msg[EXTRA_TAGDIST_INDEX], &tagdist_list[0], 4);
            }
             if(taglist_pos==0)
            {
               memcpy(&tx_nearresp_msg[EXTRA_TAGID_INDEX], &tagid_list[1], 2);
               memcpy(&tx_nearresp_msg[EXTRA_TAGDIST_INDEX], &tagdist_list[1], 4);
            }					
            dwt_writetxdata(28, tx_nearresp_msg, 0);//写入发送数据
            dwt_writetxfctrl(28, 0);//设定发送长度
         }
         result = dwt_starttx(DWT_START_TX_DELAYED | DWT_RESPONSE_EXPECTED);//延迟发送，等待接收

@@ -936,7 +990,7 @@
         {
            return 1;
         }
         if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_FINAL&&!memcmp(&rx_buffer[TAG_ID_IDX],&tag_id_recv,2)&&group_id==rx_buffer[GROUP_ID_IDX]) //判断是否为Final包
         if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_FINAL&&!memcmp(&rx_buffer[TAG_ID_IDX],&tag_id_recv,2)&&(rx_buffer[GROUP_ID_IDX]==supergroupid||rx_buffer[GROUP_ID_IDX] == group_id||group_id==supergroupid)) //判断是否为Final包
            {
               uint32_t poll_tx_ts, resp_rx_ts, final_tx_ts;
               uint32_t poll_rx_ts_32, resp_tx_ts_32, final_rx_ts_32;
@@ -1069,7 +1123,7 @@
      memcpy(&anc_id_recv,&rx_buffer[ANCHOR_ID_IDX],2);
      //将收到的tag_id分别写入各次通讯的包中，为多标签通讯服务，防止一次通讯中接收到不同ID标签的数据
      memcpy(&tag_id_recv,&rx_buffer[TAG_ID_IDX],2);
       if(group_id==rx_buffer[GROUP_ID_IDX])
       if((rx_buffer[GROUP_ID_IDX]==supergroupid||rx_buffer[GROUP_ID_IDX] == group_id||group_id==supergroupid))
       {
      switch(rx_buffer[MESSAGE_TYPE_IDX])
      {