| | |
|---|
| | | #define NSH1 0x0001 |
|---|
| | | #define GP 0x0002 |
|---|
| | | #define FLASH_HARDWARE_VERSION_MAP (uint32_t)0x08004F00 //硬件版本号和批次信息位置 |
|---|
| | | //#define DEBUG_MODE |
|---|
| | | #define DEBUG_MODE |
|---|
| | | UART_WakeUpTypeDef Selection; |
|---|
| | | /* USER CODE END Includes */ |
|---|
| | | |
|---|
| | |
|---|
| | | hardware_pici = STMFLASH_ReadHalfWord(FLASH_HARDWARE_VERSION_MAP+2); |
|---|
| | | hardware_type = STMFLASH_ReadHalfWord(FLASH_HARDWARE_VERSION_MAP+4); |
|---|
| | | //deca_sleep(1000); |
|---|
| | | g_com_map[VERSION] = (1<<8)|17; |
|---|
| | | g_com_map[VERSION] = (2<<8)|3; |
|---|
| | | // g_com_map[DEV_ID]=1158; |
|---|
| | | g_com_map[GROUP_ID]=0; |
|---|
| | | // g_com_map[COM_INTERVAL] = 1000; |
|---|
| | |
|---|
| | | { |
|---|
| | | SystemClock_Config(); |
|---|
| | | irq_num++; |
|---|
| | | HAL_GPIO_WritePin(GPIOA, GPIO_PIN_12, GPIO_PIN_SET); |
|---|
| | | RadioIrqProcess(); |
|---|
| | | } |
|---|
| | | if(GPIO_Pin == GPIO_PIN_1)//按键 |
|---|
| | |
|---|
| | | } |
|---|
| | | |
|---|
| | | uint8_t usart5_state,flag_onesecond; |
|---|
| | | uint8_t beep_flag; |
|---|
| | | void BeepTask(void) |
|---|
| | | { |
|---|
| | | if(1)//g_com_map[MOTOR_ENABLE]) |
|---|
| | |
|---|
| | | { |
|---|
| | | motor_keeptime--; |
|---|
| | | HAL_TIM_PWM_Start(&htim2, TIM_CHANNEL_4); |
|---|
| | | beep_flag=1; |
|---|
| | | }else{ |
|---|
| | | HAL_TIM_PWM_Stop(&htim2, TIM_CHANNEL_4); |
|---|
| | | beep_flag=0; |
|---|
| | | } |
|---|
| | | } |
|---|
| | | } |
|---|
| | |
|---|
| | | MX_LPUART1_UART_Init(); |
|---|
| | | MX_LPTIM1_Init(); |
|---|
| | | /* USER CODE BEGIN 2 */ |
|---|
| | | |
|---|
| | | GPIO_InitTypeDef GPIO_InitStruct = {0}; |
|---|
| | | /*Configure GPIO pin Output Level */ |
|---|
| | | HAL_GPIO_WritePin(GPIOA, GPIO_PIN_12, GPIO_PIN_RESET); |
|---|
| | | |
|---|
| | | /*Configure GPIO pins : PA2 PA8 */ |
|---|
| | | GPIO_InitStruct.Pin = GPIO_PIN_12; |
|---|
| | | GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; |
|---|
| | | GPIO_InitStruct.Pull = GPIO_NOPULL; |
|---|
| | | GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; |
|---|
| | | HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); |
|---|
| | | |
|---|
| | | |
|---|
| | | |
|---|
| | | LED2_TB_ON; |
|---|
| | | Program_Init(); |
|---|
| | | LIS3DH_Data_Init(); |
|---|
| | |
|---|
| | | // } |
|---|
| | | LoraUp_Poll(); |
|---|
| | | #ifndef DEBUG_MODE |
|---|
| | | if(beep_flag==0) |
|---|
| | | { |
|---|
| | | if(!HAL_GPIO_ReadPin(INPUT_5V_GPIO_Port,INPUT_5V_Pin)&&motor_keeptime==0) |
|---|
| | | HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI); |
|---|
| | | } |
|---|
| | | #endif |
|---|
| | | |
|---|
| | | } |
|---|
