1.42 修改重启和单片机电压检测

yincheng.zhong

2022-11-07 6e39707d1deda59da8b133fb73b1632d75fef03d

 Src/application/dw_app.c

@@ -30,6 +30,7 @@
#include "beep.h"
#include "modbus.h"

//#define USART_INTEGRATE_OUTPUT
/*------------------------------------ Marcos ------------------------------------------*/
/* Inter-ranging delay period, in milliseconds. */
#define RNG_DELAY_MS 100
@@ -54,7 +55,7 @@

#define DELAY_BETWEEN_TWO_FRAME_UUS 400

#define POLL_RX_TO_RESP_TX_DLY_UUS 420
#define POLL_RX_TO_RESP_TX_DLY_UUS 470
/* This is the delay from the end of the frame transmission to the enable of the receiver, as programmed for the DW1000's wait for response feature. */
#define RESP_TX_TO_FINAL_RX_DLY_UUS 200
/* Receive final timeout. See NOTE 5 below. */
@@ -75,7 +76,7 @@
   DISCPOLL,
   GETNEARMSG,
   NEARPOLL,
}tag_state=GETNEARMSG;
}tag_state=NEARPOLL;
static dwt_config_t config = {
   2,               /* Channel number. */
   DWT_PRF_64M,     /* Pulse repetition frequency. */
@@ -83,7 +84,7 @@
   DWT_PAC8,        /* Preamble acquisition chunk size. Used in RX only. */
   9,               /* TX preamble code. Used in TX only. */
   9,               /* RX preamble code. Used in RX only. */
   0,               /* Use non-standard SFD (Boolean) */
   1,               /* Use non-standard SFD (Boolean) */
   DWT_BR_6M8,      /* Data rate. */
   DWT_PHRMODE_STD, /* PHY header mode. */
   (129 + 8 - 8)    /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
@@ -92,7 +93,7 @@
static uint8_t tx_sync_msg[14] = {0};
static uint8_t tx_final_msg[60] = {0};
static uint8_t tx_resp_msg[22] = {0};
static uint8_t tx_near_msg[80] = {0};
 uint8_t tx_near_msg[80] = {0};

static uint32_t frame_seq_nb = 0;   
static uint32_t status_reg = 0;
@@ -291,10 +292,11 @@
u8 flag_finalsend,flag_getresponse,flag_rxon;
uint16_t current_count,start_count,end_count,lastsync_timer;

u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum;
u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum, para_update,para_len,stationary_flag=0;
u32 rec_tagpos_binary;
int16_t offset=2700;
u8 motor_state,rec_remotepara_state,rec_remotepara[30];
u8 motor_state,rec_remotepara_state,rec_remotepara[80];
extern u16 last_lpcount;
void NearPoll(void)
{
   
@@ -304,7 +306,7 @@
   u32 start_poll;
   u8 i,j,getsync_flag=0,timeout;
    dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS);         //设置发送后开启接收，并设定延迟时间
    dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);		
    dwt_setrxtimeout(10000);		
   tag_succ_times = 0;
      //GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
   if(next_nearbase_num>=MAX_NEARBASE_NUM)
@@ -315,10 +317,10 @@
   last_nearbase_num=next_nearbase_num;
   nearbase_num=next_nearbase_num;
   recbase_num=0;
   motor_state=0;
	
//   motor_state=0;
   tx_near_msg[GROUP_ID_IDX] = group_id;
   tx_near_msg[BATTARY_IDX] = bat_percent;
   tx_near_msg[BUTTON_IDX] = !GET_USERKEY;
   tx_near_msg[BUTTON_IDX] = !GET_USERKEY|stationary_flag<<1;
   tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
   tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
   memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
@@ -328,12 +330,14 @@
   dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
   dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
   
   tx_near_msg[TAGCONFIGSUCCESS_INDEX] =0;
   para_update = 0;
   flag_finalsend=0;
   flag_rxon=1;
   flag_getresponse=0;
   start_count=HAL_LPTIM_ReadCounter(&hlptim1);
   recbase_num=0;
   timeout=ceil((float)nearbase_num*0.4)+2;
   timeout=nearbase_num*SLOT_SCALE+4;
   end_count=start_count+(timeout<<5);
   if(end_count>=32768)
   {end_count-=32768;}
@@ -374,7 +378,7 @@
                     dwt_readrxdata(rx_buffer, frame_len, 0);   //读取接收数据
                     dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
                     dwt_rxenable(0);//打开接收
                     if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
                     if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&rx_buffer[GROUP_ID_IDX]==group_id) //判断接收到的数据是否是response数据
                     {   u16 rec_nearbaseid,rec_nearbasepos;
                        poll_tx_ts = get_tx_timestamp_u64();                              //获得POLL发送时间T1
                        resp_rx_ts = get_rx_timestamp_u64();                              //获得RESPONSE接收时间T4   
@@ -427,6 +431,8 @@
                           final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
                           final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
                           tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
                                    tx_near_msg[GROUP_ID_IDX] = group_id;
									
                           dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
                           dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
                           flag_getresponse=1;
@@ -441,37 +447,18 @@
                           {flag_getresponse=1;}
                           lastsync_timer=sync_timer;
                           offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
                           SetNextPollTime(tyncpoll_time);
                           if(rec_remotepara_state&&rec_remotepara_state!=g_com_map[REMOTEPARA_STATE])
                           {
                              g_com_map[REMOTEPARA_STATE]=rec_remotepara_state;
                              memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],REMOTEPARA_LEN);
                              memcpy(&g_com_map[COM_INTERVAL],&rec_remotepara[0],8);
                              memcpy(&g_com_map[POWER],&rec_remotepara[8],10);
                              save_com_map_to_flash();
                              delay_ms(100);
                              NVIC_SystemReset();
									
                           }
									
                        //   count_offset=sync_count-current_count-143;
                        //   current_slottimes=(ancsync_time-10000)/(g_com_map[COM_INTERVAL]*1000);
                        //   nextpoll_delaytime=tyncpoll_time*1000+g_com_map[COM_INTERVAL]*1000-((ancsync_time)%(g_com_map[COM_INTERVAL]*1000))-4300;
//                           if(abs(ancsync_time-910000)<1000)
//                           SetNextPollTime(tyncpoll_time);
//                           if(rec_remotepara_state==1)
//                           {
//                           nextpoll_delaytime+=10000;
//                           }		
//                           if(nextpoll_delaytime<2000)
//                           {
//                              nextpoll_delaytime+=g_com_map[COM_INTERVAL]*1000;
//                           }
//                           lastpoll_count= current_count+(nextpoll_delaytime)/LPTIMER_LSB;
//                           if(lastpoll_count>LPTIMER_1S_COUNT)
//                              lastpoll_count-=LPTIMER_1S_COUNT;
//                           __HAL_LPTIM_COMPARE_SET(&hlptim1, lastpoll_count);
         /////////////////////////////////////////
//                           dwt_setdelayedtrxtime(final_tx_time);
//                        result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送	
//                                      memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],REMOTEPARA_LEN);
//                              memcpy(&g_com_map[COM_INTERVAL],&rec_remotepara[0],8);
//                              memcpy(&g_com_map[POWER],&rec_remotepara[8],10);
//                                        if(g_com_map[COM_INTERVAL]>0&&g_com_map[COM_INTERVAL]<1000&&g_com_map[POWER]<67&&g_com_map[POWER]>0)
//                              {save_com_map_to_flash();
//                              delay_ms(100);										
//                                        }
//                                        NVIC_SystemReset();
//                           } 
                        }else{
                           rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
                           
@@ -491,12 +478,10 @@
                           {
                                 motor_state=rx_buffer[MOTORSTATE_INDEX];
                           }
									
                           final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);                        
                           dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
                           dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
                        


                           //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
                        //   result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送         
@@ -511,24 +496,13 @@
                  }         
               //   dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
         }
dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
         nearbase_num=recbase_num;
      j=0;
         if(exsistbase_list[0]==0)
         {
//          u8 temp_adc,random_value;
//            random_value=0;
//            for(i=0;i<8;i++)
//            {
//               temp_adc=Get_ADC_Value();
//               random_value=random_value|((temp_adc&0x01)<<i);
//            }
            tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
            tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;	
            SetNextPollTime(tyncpoll_time);
         }
         if(mainbase_lost_count>tag_frequency*BASELOST_STOPMOTOR_TIME)
         {motor_state=0; }
            dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
            nearbase_num=recbase_num;
      //   tyncpoll_time=0;
         next_nearbase_num=0;
            j = 0;
         for(i=0;i<last_nearbase_num+get_newbase;i++)
         {
            if(exsistbase_list[i]>0)
@@ -540,10 +514,11 @@
               exsistbase_list[i]--;
            }
         }

         if(recbase_num<3)
         {next_nearbase_num=next_nearbase_num;}
               last_nearbase_num = next_nearbase_num;
            if(mainbase_lost_count>1&&exsistbase_list[0] != 0)
         {
                last_lpcount+= HAL_LPTIM_ReadCounter(&hlptim1)%(g_com_map[COM_INTERVAL]*16);
         }
            last_nearbase_num = next_nearbase_num;
         for(i=0;i<last_nearbase_num-1;i++)
         {
            for(j=0;j<last_nearbase_num-1;j++)
@@ -570,18 +545,27 @@
         {
            nearbaseid_list[i]=true_nearbase_idlist[i];
            nearbase_distlist[i]=true_nearbase_distlist[i];
            if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==0xa)
            if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==KEEP_TIMES)
            {
               memcpy(&usart_send[4+6*report_num],&nearbaseid_list[i],2);
               memcpy(&usart_send[6+6*report_num],&nearbase_distlist[i],4);
               report_num++;
            }
         }
            #ifdef USART_INTEGRATE_OUTPUT	
                usart_send[0] = 0x55;     
                usart_send[1] = 0xAA;              
            usart_send[2] = 4;//正常模式
            usart_send[3] = report_num*6+2;//正常模式
            checksum = Checksum_u16(&usart_send[2],report_num*6+2);
            memcpy(&usart_send[4+report_num*6],&checksum,2);
            USART_puts(usart_send,6+report_num*6);
         #endif
            
         for(i=0;i<MAX_NEARBASE_NUM;i++)
         {
            nearbase_distlist[i]=0x1ffff;
         }
			
   dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);

@@ -597,6 +581,7 @@
   }
   memcpy(&tx_near_msg[ANCHOR_ID_IDX],&nearmsg_mainbase,2);
   memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
    tx_near_msg[GROUP_ID_IDX] = group_id;
   tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
   
   dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS);         //设置发送后开启接收，并设定延迟时间
@@ -633,10 +618,10 @@
         tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
   }
}

u32 id;
void Tag_App(void)//发送模式(TAG标签)
{
   u32 id;
	
   //LED0_ON;
   id =  dwt_readdevid() ;
       while (DWT_DEVICE_ID != id) 
@@ -662,5 +647,6 @@
         //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_RESET);
         break;
   }
//   dwt_entersleep();
   dwt_entersleep();
    bat_percent=Get_VDDVlotage();
}