XRange_Tag.git - Gitblit

			@@ -2,22 +2,22 @@
			******************************************************************************
			* @file stm32l0xx_hal_conf.h
			* @author MCD Application Team
			* @brief HAL configuration template file.
			* @brief HAL configuration template file.
			* This file should be copied to the application folder and renamed
			* to stm32l0xx_hal_conf.h.
			******************************************************************************
			* @attention
			*
			* <h2><center>© Copyright (c) 2016 STMicroelectronics.
			* <h2><center>© Copyright (c) 2016 STMicroelectronics.
			* All rights reserved.</center></h2>
			*
			* This software component is licensed by ST under BSD 3-Clause license,
			* the "License"; You may not use this file except in compliance with the
			* the "License"; You may not use this file except in compliance with the
			* License. You may obtain a copy of the License at:
			* opensource.org/licenses/BSD-3-Clause
			*
			******************************************************************************
			*/
			*/

			/* Define to prevent recursive inclusion -------------------------------------*/
			#ifndef __STM32L0xx_HAL_CONF_H
			@@ -32,10 +32,10 @@

			/* ########################## Module Selection ############################## */
			/**
			* @brief This is the list of modules to be used in the HAL driver
			* @brief This is the list of modules to be used in the HAL driver
			*/

			#define HAL_MODULE_ENABLED
			#define HAL_MODULE_ENABLED
			#define HAL_ADC_MODULE_ENABLED
			/#define HAL_CRYP_MODULE_ENABLED /
			/#define HAL_COMP_MODULE_ENABLED /
			@@ -50,7 +50,7 @@
			/#define HAL_RNG_MODULE_ENABLED /
			/#define HAL_RTC_MODULE_ENABLED /
			#define HAL_SPI_MODULE_ENABLED
			/#define HAL_TIM_MODULE_ENABLED /
			#define HAL_TIM_MODULE_ENABLED
			/#define HAL_TSC_MODULE_ENABLED /
			#define HAL_UART_MODULE_ENABLED
			/#define HAL_USART_MODULE_ENABLED /
			@@ -72,9 +72,9 @@
			/**
			* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
			* This value is used by the RCC HAL module to compute the system frequency
			* (when HSE is used as system clock source, directly or through the PLL).
			* (when HSE is used as system clock source, directly or through the PLL).
			*/
			#if !defined (HSE_VALUE)
			#if !defined (HSE_VALUE)
			#define HSE_VALUE ((uint32_t)8000000U) /!< Value of the External oscillator in Hz /
			#endif /* HSE_VALUE */

			@@ -89,11 +89,11 @@
			#if !defined (MSI_VALUE)
			#define MSI_VALUE ((uint32_t)2097000U) /!< Value of the Internal oscillator in Hz/
			#endif /* MSI_VALUE */


			/**
			* @brief Internal High Speed oscillator (HSI) value.
			* This value is used by the RCC HAL module to compute the system frequency
			* (when HSI is used as system clock source, directly or through the PLL).
			* (when HSI is used as system clock source, directly or through the PLL).
			*/
			#if !defined (HSI_VALUE)
			#define HSI_VALUE ((uint32_t)16000000U) /!< Value of the Internal oscillator in Hz/
			@@ -102,7 +102,7 @@
			/**
			* @brief Internal High Speed oscillator for USB (HSI48) value.
			*/
			#if !defined (HSI48_VALUE)
			#if !defined (HSI48_VALUE)
			#define HSI48_VALUE ((uint32_t)48000000U) /*!< Value of the Internal High Speed oscillator for USB in Hz.
			The real value may vary depending on the variations
			in voltage and temperature. */
			@@ -111,11 +111,11 @@
			/**
			* @brief Internal Low Speed oscillator (LSI) value.
			*/
			#if !defined (LSI_VALUE)
			#if !defined (LSI_VALUE)
			#define LSI_VALUE ((uint32_t)37000U) /!< LSI Typical Value in Hz/
			#endif /* LSI_VALUE / /!< Value of the Internal Low Speed oscillator in Hz
			The real value may vary depending on the variations
			in voltage and temperature.*/
			in voltage and temperature.*/
			/**
			* @brief External Low Speed oscillator (LSE) value.
			* This value is used by the UART, RTC HAL module to compute the system frequency
			@@ -134,24 +134,24 @@
			/* ########################### System Configuration ######################### */
			/**
			* @brief This is the HAL system configuration section
			*/
			#define VDD_VALUE ((uint32_t)3300U) /!< Value of VDD in mv /
			#define TICK_INT_PRIORITY ((uint32_t)0U) /!< tick interrupt priority /
			#define USE_RTOS 0U
			#define PREFETCH_ENABLE 0U
			*/
			#define VDD_VALUE ((uint32_t)3300U) /!< Value of VDD in mv /
			#define TICK_INT_PRIORITY ((uint32_t)0U) /!< tick interrupt priority /
			#define USE_RTOS 0U
			#define PREFETCH_ENABLE 0U
			#define PREREAD_ENABLE 1U
			#define BUFFER_CACHE_DISABLE 0U

			/* ########################## Assert Selection ############################## */
			/**
			* @brief Uncomment the line below to expanse the "assert_param" macro in the
			* @brief Uncomment the line below to expanse the "assert_param" macro in the
			* HAL drivers code
			*/
			/* #define USE_FULL_ASSERT 1U */

			/* Includes ------------------------------------------------------------------*/
			/**
			* @brief Include module's header file
			* @brief Include module's header file
			*/

			#ifdef HAL_RCC_MODULE_ENABLED
			@@ -169,7 +169,7 @@
			#ifdef HAL_DMA_MODULE_ENABLED
			#include "stm32l0xx_hal_dma.h"
			#endif /* HAL_DMA_MODULE_ENABLED */


			#ifdef HAL_CORTEX_MODULE_ENABLED
			#include "stm32l0xx_hal_cortex.h"
			#endif /* HAL_CORTEX_MODULE_ENABLED */
			@@ -181,7 +181,7 @@
			#ifdef HAL_COMP_MODULE_ENABLED
			#include "stm32l0xx_hal_comp.h"
			#endif /* HAL_COMP_MODULE_ENABLED */


			#ifdef HAL_CRC_MODULE_ENABLED
			#include "stm32l0xx_hal_crc.h"
			#endif /* HAL_CRC_MODULE_ENABLED */
			@@ -201,7 +201,7 @@
			#ifdef HAL_FLASH_MODULE_ENABLED
			#include "stm32l0xx_hal_flash.h"
			#endif /* HAL_FLASH_MODULE_ENABLED */


			#ifdef HAL_I2C_MODULE_ENABLED
			#include "stm32l0xx_hal_i2c.h"
			#endif /* HAL_I2C_MODULE_ENABLED */
			@@ -221,7 +221,7 @@
			#ifdef HAL_LPTIM_MODULE_ENABLED
			#include "stm32l0xx_hal_lptim.h"
			#endif /* HAL_LPTIM_MODULE_ENABLED */


			#ifdef HAL_PWR_MODULE_ENABLED
			#include "stm32l0xx_hal_pwr.h"
			#endif /* HAL_PWR_MODULE_ENABLED */
			@@ -281,7 +281,7 @@
			* @brief The assert_param macro is used for function's parameters check.
			* @param expr: If expr is false, it calls assert_failed function
			* which reports the name of the source file and the source
			* line number of the call that failed.
			* line number of the call that failed.
			* If expr is true, it returns no value.
			* @retval None
			*/
			@@ -297,6 +297,5 @@
			#endif

			#endif /* __STM32L0xx_HAL_CONF_H */


			/********************** (C) COPYRIGHT STMicroelectronics *END OF FILE**/