From 2b40605dbb9622b2099f7c4c6a628e40cd17e805 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期四, 29 五月 2025 18:11:01 +0800
Subject: [PATCH] 基本完成免布线基站测试固件,功耗升级等未测试
---
keil/include/main/main.c | 45 +++++++++++++++++++++++++++++++++++----------
1 files changed, 35 insertions(+), 10 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 9de8816..0080c8e 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -61,7 +61,7 @@
#define TEST_UART_MODE TEST_UART_DMA_MODE
#define NUM_SAMPLES 1
-#define SLEEP_START_TIME 1
+#define SLEEP_START_TIME 10
#define FREQ_LOST_TIME 5
#define NOTAG_FREQ 1
#define BATTERY_GET_TIME 3600
@@ -118,7 +118,7 @@
.callback = app_wdt_callback,
};
-uint8_t state5v = 1;
+uint8_t state5v = 0;
uint8_t bat_percent=0,g_start_send_flag=1;
int16_t fVoltage_mv;
uint8_t bat_percent;
@@ -133,6 +133,7 @@
void boot_deinit(void);
void Get_batterty_Voltage(void);
void Calculate_battery_percent(void);
+uint8_t sleep_limit_time=10;
static void uart_receive_callback(void *dev, uint32_t err_code)
{
uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
@@ -149,12 +150,19 @@
uart_close(UART_ID0);
uart_close(UART_ID1);
}
+uint8_t bat_flag;
void Get_batterty_Voltage(void)
{
battery_monitor_open();
fVoltage_mv=battery_monitor_get();
battery_monitor_close();
- Calculate_battery_percent();
+ if(fVoltage_mv>=3200&&fVoltage_mv<=3400)
+ {
+ bat_flag=1;//正常
+ }else{
+ bat_flag=0;//不正常
+ }
+ //Calculate_battery_percent();
}
void Calculate_battery_percent(void)
{
@@ -170,6 +178,7 @@
{
bat_percent = ((fVoltage_mv - 3000) /8);
}
+
//LOG_INFO(TRACE_MODULE_APP, "The voltage is %d ,percent is %%%d \r\n",fVoltage_mv,bat_percent);
}
static void sleep_timer_callback(void *dev, uint32_t time)
@@ -180,8 +189,8 @@
if(reboot_num>=3600)
NVIC_SystemReset(); //软复位回到bootloader
enable_sleep_count++;
- if(enable_sleep_count==SLEEP_START_TIME){
-
+
+ if(enable_sleep_count==sleep_limit_time){
enable_sleep_count=0;
sleep_flag=1;
}
@@ -239,21 +248,25 @@
group_id=g_com_map[GROUP_ID];
memcpy(&dev_id ,&g_com_map[DEV_ID],2);
tag_frequency=1000/g_com_map[COM_INTERVAL];
-g_com_map[VERSION] = (1<<8)|11;
+g_com_map[VERSION] = (1<<8)|12;
LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-免布线信标 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
}
+uint8_t test1;
+extern uint8_t change_power_flag;
void IdleTask(void)
{ UART0_CheckReceive();
+ test1=gpio_pin_get_val(INPUT_5V_Pin);
if(gpio_pin_get_val(INPUT_5V_Pin))
{
-
-
//UART_CheckSend();
// bat_percent=Get_Battary();
if(state5v==0)
{
state5v=1;
+ sleep_flag=0;
+ sleep_limit_time=30;//新增插入串口后30s不休眠
+ enable_sleep_count=0;//重新插拔可以重置时间
}
}else{
if(state5v==1)
@@ -277,6 +290,12 @@
uart_close(UART_ID1);//解绑原来串口1
uart_close(UART_ID0);//解绑原来串口0
}
+void power_mode_start(void)
+{
+LED_PA_change();//将PA管脚改为gpio模式发射载波开启功率测试
+
+}
+
int main(void)
{
board_clock_run();
@@ -338,14 +357,20 @@
#endif
//Serial0_PutString("进入app测试\r\n");
while (1)
- { wdt_ping(WDT_ID0);//喂狗
+ {
if(g_start_send_flag)
{
//LOG_INFO(TRACE_MODULE_APP, "测距ing");
-
+ wdt_ping(WDT_ID0);//喂狗
g_start_send_flag = 0;
gpio_pin_set(LED_PIN);//亮
+ if(!change_power_flag)
TagRange();
+ if(change_power_flag)
+ {
+ power_mode_start();
+ uwb_power_init();
+ }
gpio_pin_clr(LED_PIN);//灭
IdleTask();
}else{
--
Gitblit v1.9.3