From 345e9e9ae770e3ef884568a96a95e141236c5968 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期三, 25 十二月 2024 18:18:59 +0800
Subject: [PATCH] 目前成功的是基站端原代码rx写法帧间隔500，延时550，标签那边帧间隔500 基站default为600，成功低功耗帧间隔版本（标签常开）
---
keil/uwb_app.c | 132 +++++++++++++++++++++++++------------------
1 files changed, 77 insertions(+), 55 deletions(-)
diff --git a/keil/uwb_app.c b/keil/uwb_app.c
index a5a38f3..c81a59b 100644
--- a/keil/uwb_app.c
+++ b/keil/uwb_app.c
@@ -78,7 +78,7 @@
#define RANGING_PERIOD_MS (1000)
/* This is the delay from Frame RX POLL frame to send RESP Frame */
-#define POLL_RX_TO_RESP_TX_DLY_US 2000U //yuan670 with urt 3000success
+#define POLL_RX_TO_RESP_TX_DLY_US 550U //yuan600 success 并且不卡busy
#define RESP_TX_TO_FINAL_RX_DLY_US 500U
@@ -97,7 +97,7 @@
/* RX window open in advance */
#define RX_WIN_IN_ADVANCE_US (150)
-#define DELAY_BETWEEN_TWO_FRAME_UUS 300 //yuan1400
+#define DELAY_BETWEEN_TWO_FRAME_UUS 500 //yuan1400
/* Field index in frame */
#define MSG_SEQ_NUM_IDX 2
@@ -133,7 +133,7 @@
// .phy_cfg.sts_seglen = STS_SEGLEN_BPRF_64, /* Number of symbols in an STS segment */
// .phy_cfg.rx_ant_id = UWB_RX_ANT_3, /* UWB RX antenna port */
//};
-#ifndef STS_MODE
+#ifdef DW1000
static struct mk_uwb_configure config = {
.phy_work_mode = (uint8_t)(PHY_TX | PHY_RX),
.phy_cfg.ch_num = 5, /* Channel number. */
@@ -149,7 +149,7 @@
.phy_cfg.sts_seglen = STS_SEGLEN_BPRF_64, /* Number of symbols in an STS segment */
.phy_cfg.rx_ant_id = UWB_RX_ANT_3, /* UWB RX antenna port */
};
-#else
+#elif defined STS_MODE
static struct mk_uwb_configure config = {
.phy_work_mode = (uint8_t)(PHY_TX | PHY_RX),
.phy_cfg.ch_num = 5, /* Channel number. */
@@ -165,7 +165,6 @@
.phy_cfg.sts_seglen = STS_SEGLEN_BPRF_64, /* Number of symbols in an STS segment */
.phy_cfg.rx_ant_id = UWB_RX_ANT_3, /* UWB RX antenna port */
};
-#endif
/* Use the default key and IV specified in the IEEE 802.15.4z attachment */
static struct UWB_STS_KEY_CONFIG_T sts_iv_key = {
.sts_vcounter = 0x1F9A3DE4,
@@ -177,6 +176,24 @@
.sts_key2 = 0xD1D336AA,
.sts_key3 = 0x14148674,
};
+#elif defined MK_MODE
+static struct mk_uwb_configure config = {
+ .phy_work_mode = (uint8_t)(PHY_TX | PHY_RX),
+ .phy_cfg.ch_num = 9, /* Channel number. */
+ .phy_cfg.code_index = 9, /* TX preamble code. */
+ .phy_cfg.mean_prf = MEAN_PRF_64M, /* Data rate 6.8M */
+ .phy_cfg.data_bit_rate = DATA_BR_6M8, /* data rate 6.8M. */
+ .phy_cfg.sync_sym = PREAM_LEN_128, /* Preamble duration, length of preamble 128 */
+ .phy_cfg.sfd_sym = BPRF_NSFD2_8, /* Identifier for SFD sequence */
+ .phy_cfg.ranging_bit = 1, /* ranging bit set. */
+ .phy_cfg.trx_mode = TRX_MODE_15_4Z_BPRF, /* IEEE802.15.4z - BPRF mode */
+ .phy_cfg.sts_pkt_cfg = STS_PKT_CFG_0, /* SP0 Frame */
+ .phy_cfg.sts_segnum = STS_SEGNUM_BPRF_1, /* Number of STS segments in the frame */
+ .phy_cfg.sts_seglen = STS_SEGLEN_BPRF_64, /* Number of symbols in an STS segment */
+ .phy_cfg.rx_ant_id = UWB_RX_ANT_3, /* UWB RX antenna port */
+};
+#endif
+
static struct anchor_id_car{
uint16_t anchor_new_id;
uint16_t change_num;
@@ -312,9 +329,9 @@
temp_count= phy_timer_count_get();
memcpy(&rx_rpt, rx_report, sizeof(struct MAC_HW_REPORT_T));
rx_length = 0;
- OpenUWB();//再次开启UWB接收
+ // OpenUWB();//再次开启UWB接收
}
- //OpenUWB();//再次开启UWB接收
+ OpenUWB();//再次开启UWB接收
}
/* TX done process handler. */
@@ -329,7 +346,7 @@
temp_count= phy_timer_count_get();
temp_internal=temp_count;
resp_tx_num++;
- OpenUWB();//再次开启UWB接收
+ // OpenUWB();//再次开启UWB接收
//LOG_INFO(TRACE_MODULE_APP, "poll_rx_num is %d,resp_tx_num is %d\r\n",poll_rx_num,resp_tx_num);
}
}
@@ -427,7 +444,7 @@
}
-
+uint8_t position;
uint8_t Anchor_RecNearPoll(uint8_t ancrec_nearbasepos)//根据自己是否为新基站定制消息去发送，根据是否抢占判断
{
temp_count2=poll_rx_en_start_u32;
@@ -449,7 +466,8 @@
// resp_tx_en_start_u32 = phy_timer_count_get()+US_TO_PHY_TIMER_COUNT(20*rec_nearbase_num+POLL_RX_TO_RESP_TX_DLY_US+ancrec_nearbasepos*DELAY_BETWEEN_TWO_FRAME_UUS);//后面的需要根据已有基站数量进行更改，如果是抢占自己最后一个回复，要有底数
// //这里应该有问题问一下钟工
// }//此处设置绝对时间将poll u32改为phy_timer_count_get()
- resp_tx_en_start_u32 = poll_rx_en_start_u32+US_TO_PHY_TIMER_COUNT(POLL_RX_TO_RESP_TX_DLY_US);
+ position=ancrec_nearbasepos;
+ resp_tx_en_start_u32 = poll_rx_en_start_u32+US_TO_PHY_TIMER_COUNT(POLL_RX_TO_RESP_TX_DLY_US)+ancrec_nearbasepos*US_TO_PHY_TIMER_COUNT(DELAY_BETWEEN_TWO_FRAME_UUS);//加入帧间隔
resp_tx_ts_i64 = ranging_tx_time_correct(resp_tx_en_start_u32 + phy_shr_duration());//修正时间戳
/* Write all timestamps in the final message. See NOTE 8 below. */
resp_msg_set_ts(&send_buffer[RESP_MSG_POLL_RX_TS_IDX], poll_rx_ts_i64);
@@ -458,9 +476,9 @@
temp_resp_i64=resp_tx_ts_i64;
temp_count3= phy_timer_count_get();
flag_temp2=uwb_tx(send_buffer, 40,1 ,resp_tx_en_start_u32);//立即发送测试size大小
- temp_count1=phy_timer_count_get();
+// temp_count1=phy_timer_count_get();
//while(mac_is_busy());
- gpio_pin_clr(SCL_PIN);
+ //gpio_pin_clr(SCL_PIN);
}
uint16_t uwb_searchcount;
@@ -534,7 +552,10 @@
}
void UWBOneSecondTask(void)
{
+ TagListUpdate();//更新标签数
uwb_losttimer++;
+ if(uwb_losttimer>g_com_map[UWB_RNAGE_TIME])
+ uwb_losttimer=g_com_map[UWB_RNAGE_TIME]+1;//防止溢出
}
void UWBIdleTask(void)
{
@@ -547,46 +568,46 @@
}
int uwb_app_poll(void)
{
- switch(wltag_state)
- {
- case RANGE:
- if(HIDO_TimerGetTick()-wltag_uwbtimer>2&&uwb_rx_flag==0)
- {
- wltag_uwbtimer = HIDO_TimerGetTick();
- OpenUWB();
- }
- else if(HIDO_TimerGetTick()-wltag_uwbtimer>1&&uwb_rx_flag==1)
- {
- wltag_uwbtimer = HIDO_TimerGetTick();
- CloseUWB();
- }
- if(uwb_losttimer>g_com_map[UWB_RNAGE_TIME])
- {
- wltag_statetimer = HIDO_TimerGetTick();
- if(uwb_rx_flag==0)//若要切换到搜索模式时没有开启则开启UWB
- {
- OpenUWB();
- }
- wltag_state = SEARCH;
- }
- break;
- case SEARCH:
- if(HIDO_TimerGetTick()-wltag_statetimer>1)
- {
- wltag_statetimer = HIDO_TimerGetTick();
- wltag_state = CLOSE;
- CloseUWB();
- }
- break;
- case CLOSE:
- if(HIDO_TimerGetTick()-wltag_statetimer>g_com_map[UWB_WAIT_TIME])
- {
- wltag_statetimer = HIDO_TimerGetTick();
- wltag_state = SEARCH;
- OpenUWB();
- }
- break;
- }
+// switch(wltag_state)
+// {
+// case RANGE:
+// if(HIDO_TimerGetTick()-wltag_uwbtimer>0&&uwb_rx_flag==0)
+// {
+// wltag_uwbtimer = HIDO_TimerGetTick();
+// OpenUWB();
+// }
+// else if(HIDO_TimerGetTick()-wltag_uwbtimer>2&&uwb_rx_flag==1)
+// {
+// wltag_uwbtimer = HIDO_TimerGetTick();
+// CloseUWB();
+// }
+//// if(uwb_losttimer>g_com_map[UWB_RNAGE_TIME])
+//// {
+//// wltag_statetimer = HIDO_TimerGetTick();
+//// if(uwb_rx_flag==0)//若要切换到搜索模式时没有开启则开启UWB
+//// {
+//// OpenUWB();
+//// }
+//// wltag_state = SEARCH;
+//// }
+// break;
+//// case SEARCH:
+//// if(HIDO_TimerGetTick()-wltag_statetimer>1)
+//// {
+//// wltag_statetimer = HIDO_TimerGetTick();
+//// wltag_state = CLOSE;
+//// CloseUWB();
+//// }
+//// break;
+//// case CLOSE:
+//// if(HIDO_TimerGetTick()-wltag_statetimer>g_com_map[UWB_WAIT_TIME])
+//// {
+//// wltag_statetimer = HIDO_TimerGetTick();
+//// wltag_state = SEARCH;
+//// OpenUWB();
+//// }
+//// break;
+// }
UWBIdleTask();
}
int Anchor_App(void)
@@ -595,8 +616,9 @@
uint16_t tempid;
if(group_id==rx_buf[GROUP_ID_IDX]&&rx_buf[MESSAGE_TYPE_IDX] == MBX_POLL)//判断是否是和自己是同一组通讯的且为poll包
{ flag_recsuccess = 1;
+ wltag_state=RANGE;//成功后从search切换为range
memcpy(&g_com_receive_id,&rx_buf[TAG_ID_IDX],2);
- temp_count2=phy_timer_count_get();
+ //temp_count2=phy_timer_count_get();
uwb_losttimer=0;//成功测距清0 lost时间
frame_seq_nb2 = rx_buf[SEQUENCE_IDX];//获取包序
battary = rx_buf[BATTARY_IDX];
@@ -630,7 +652,7 @@
Anchor_RecNearPoll(i);
}
}else{
- OpenUWB();//接收到不是自己的包再次开启UWB接收
+ // OpenUWB();//接收到不是自己的包再次开启UWB接收
}
}
@@ -802,7 +824,7 @@
// uwb configure
uwb_configure(config.phy_work_mode, board_param.tx_power_fcc[CALIB_CH(config.phy_cfg.ch_num)], &config.phy_cfg);
- #ifdef STS_MODE
+ #if (defined STS_MODE) || (defined MK_MODE)
ranging_lib_init();
#endif
ranging_frame_type_set(config.phy_cfg.sts_pkt_cfg);
--
Gitblit v1.9.3