From 387d1ffc16ce9e050403baee0ed07f3d9accf632 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期五, 04 七月 2025 14:55:15 +0800
Subject: [PATCH] 初步移植完成0.6.8SDK，但发送有len太长未找到原因
---
keil/include/main/main.c | 56 +++++++++++++++++++++++++++++++-------------------------
1 files changed, 31 insertions(+), 25 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 9de8816..8c7fd88 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -61,7 +61,7 @@
#define TEST_UART_MODE TEST_UART_DMA_MODE
#define NUM_SAMPLES 1
-#define SLEEP_START_TIME 1
+#define SLEEP_START_TIME 10
#define FREQ_LOST_TIME 5
#define NOTAG_FREQ 1
#define BATTERY_GET_TIME 3600
@@ -118,7 +118,7 @@
.callback = app_wdt_callback,
};
-uint8_t state5v = 1;
+uint8_t state5v = 0;
uint8_t bat_percent=0,g_start_send_flag=1;
int16_t fVoltage_mv;
uint8_t bat_percent;
@@ -133,6 +133,7 @@
void boot_deinit(void);
void Get_batterty_Voltage(void);
void Calculate_battery_percent(void);
+uint8_t sleep_limit_time=1;
static void uart_receive_callback(void *dev, uint32_t err_code)
{
uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
@@ -180,8 +181,8 @@
if(reboot_num>=3600)
NVIC_SystemReset(); //软复位回到bootloader
enable_sleep_count++;
- if(enable_sleep_count==SLEEP_START_TIME){
-
+
+ if(enable_sleep_count==sleep_limit_time){
enable_sleep_count=0;
sleep_flag=1;
}
@@ -239,21 +240,24 @@
group_id=g_com_map[GROUP_ID];
memcpy(&dev_id ,&g_com_map[DEV_ID],2);
tag_frequency=1000/g_com_map[COM_INTERVAL];
-g_com_map[VERSION] = (1<<8)|11;
+g_com_map[VERSION] = (1<<8)|12;
LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-免布线信标 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
}
+uint8_t test1;
void IdleTask(void)
{ UART0_CheckReceive();
+ test1=gpio_pin_get_val(INPUT_5V_Pin);
if(gpio_pin_get_val(INPUT_5V_Pin))
{
-
-
//UART_CheckSend();
// bat_percent=Get_Battary();
if(state5v==0)
{
state5v=1;
+ sleep_flag=0;
+ sleep_limit_time=30;//新增插入串口后30s不休眠
+ enable_sleep_count=0;//重新插拔可以重置时间
}
}else{
if(state5v==1)
@@ -286,20 +290,21 @@
// Reset reason
reset_cause_get();
reset_cause_clear();
- // Load calibration parameters from NVM
- uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
- uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
- if (internal_flash || external_flash == 1)
- {
- WsfNvmInit();
- board_calibration_params_load();
- flash_close(FLASH_ID0);
- }
- else
- {
- board_calibration_params_default();
- }
-
+// // Load calibration parameters from NVM
+// uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
+// uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
+// if (internal_flash || external_flash == 1)
+// {
+// WsfNvmInit();
+// board_calibration_params_load();
+// flash_close(FLASH_ID0);
+// }
+// else
+// {
+// board_calibration_params_default();
+// }
+ // Load calibration parameters
+ board_calibration_params_load();
// Chip calibration
calib_chip();
@@ -326,8 +331,9 @@
//adc_open(&usr_adc_cfg);
//adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
// Enable sleep timer
- Tag_uwb_init();
- sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
+ //Tag_uwb_init();
+ Anchor_uwb_aoa_square_init();
+ sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
//sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
sleep_timer_start(__MS_TO_32K_CNT(SLEEP_COUNT));//测试
//board_5V_input_init(voltage_input_handler);//有修改3.3V会一直高电平导致无法进入休眠
@@ -338,11 +344,11 @@
#endif
//Serial0_PutString("进入app测试\r\n");
while (1)
- { wdt_ping(WDT_ID0);//喂狗
+ {
if(g_start_send_flag)
{
//LOG_INFO(TRACE_MODULE_APP, "测距ing");
-
+ wdt_ping(WDT_ID0);//喂狗
g_start_send_flag = 0;
gpio_pin_set(LED_PIN);//亮
TagRange();
--
Gitblit v1.9.3