From 59dc136533bb8d768953a2b2799cae6cf8d02982 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期四, 31 十月 2024 18:12:56 +0800
Subject: [PATCH] 增加小于3.3V供电不足，停止震动，GPS和4G功能，增加自动检测供电足够后开启4G，GPS，震动功能，增加静止休眠逻辑。g_com_map表中4G发送频率上位机未改，供电不足下单片机不进入低功耗bug未解决，
---
keil/include/board/board.c | 14 +++++++++++++-
1 files changed, 13 insertions(+), 1 deletions(-)
diff --git a/keil/include/board/board.c b/keil/include/board/board.c
index 21702e4..80327cf 100644
--- a/keil/include/board/board.c
+++ b/keil/include/board/board.c
@@ -64,6 +64,7 @@
static GPIO_IRQ_HANDLER_T accelerate_irq_handler=NULL;
GPIO_IRQ_HANDLER_T _4Gusart_irq_handler=NULL;
extern struct UART_CFG_T test_uart_cfg;
+extern struct ADC_CFG_T usr_adc_cfg;
void board_clock_run(void)
{
// default load cap
@@ -403,7 +404,8 @@
accelerate_irq_handler=irq_handler;
gpio_pin_set_dir(ACCLERATE_DETECT_Pin , GPIO_DIR_IN, 0);
io_pull_set(ACCLERATE_DETECT_Pin, IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
- gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
+ gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
+
}
void board_4GUsart_detection_init(GPIO_IRQ_HANDLER_T irq_handler) //4G 串口输入检测中断，下拉触发
{
@@ -429,7 +431,15 @@
gpio_pin_set_dir(BOARD_LED_1, GPIO_DIR_OUT, 0);
gpio_pin_set_dir(BOARD_LED_2, GPIO_DIR_OUT, 0);
}
+void board_output_init(void)
+{
+ //adc采集gnd默认拉高
+ io_pin_mux_set(ADC_GND_ENABLE, IO_FUNC0);
+ gpio_pin_set_dir(ADC_GND_ENABLE , GPIO_DIR_OUT, 1);
+// io_open_drain_set(ADC_GND_ENABLE, 1);
+ io_pull_set(ADC_GND_ENABLE,IO_HIGH_Z,IO_PULL_UP_NONE);//3
+}
void board_led_on(enum IO_PIN_T idx)
{
gpio_pin_set(idx);
@@ -460,11 +470,13 @@
{
uart_open(UART_ID1, &test_uart_cfg);
AIR780EUartInit();
+ adc_open(&usr_adc_cfg);
#if defined(UCI_INTF_PORT)
uci_tl_resume();
#else
// button - restore interrupt type
gpio_enable_irq(_4G_USART_RX_Pin, GPIO_IRQ_TYPE_FALLING_EDGE, _4Gusart_irq_handler);
+ gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
// if (button_irq_handler)
// {
// gpio_enable_irq(BOARD_SW_1, GPIO_IRQ_TYPE_FALLING_EDGE, button_irq_handler);
--
Gitblit v1.9.3