From 6facaabcb51a77459d098b4957213038e6bb0a73 Mon Sep 17 00:00:00 2001
From: WXK <287788329@qq.com>
Date: 星期三, 05 三月 2025 16:06:30 +0800
Subject: [PATCH] 1.1，功能开发完成
---
keil/include/board/board.c | 20 +++++++++-----------
1 files changed, 9 insertions(+), 11 deletions(-)
diff --git a/keil/include/board/board.c b/keil/include/board/board.c
index ae6dfd1..b0fada6 100644
--- a/keil/include/board/board.c
+++ b/keil/include/board/board.c
@@ -415,7 +415,6 @@
gpio_pin_set_dir(ACCLERATE_DETECT_Pin , GPIO_DIR_IN, 0);
io_pull_set(ACCLERATE_DETECT_Pin, IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
-
}
void board_4GUsart_detection_init(GPIO_IRQ_HANDLER_T irq_handler) //4G 串口输入检测中断，下拉触发
{
@@ -424,7 +423,7 @@
gpio_pin_set_dir(_4G_USART_RX_Pin , GPIO_DIR_IN, 0);
io_pull_set(_4G_USART_RX_Pin, IO_PULL_UP, IO_PULL_UP_LEVEL2);
gpio_enable_irq(_4G_USART_RX_Pin, GPIO_IRQ_TYPE_FALLING_EDGE, _4Gusart_irq_handler);
- power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)_4G_USART_RX_Pin, POWER_WAKEUP_LEVEL_LOW);
+// power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)_4G_USART_RX_Pin, POWER_WAKEUP_LEVEL_LOW);
}
void pca_input_detection_init(GPIO_IRQ_HANDLER_T irq_handler)
{
@@ -464,13 +463,12 @@
{
gpio_pin_toggle(idx);
}
-void board_output_init(void)
-{
- //adc采集gnd默认拉高
- io_pin_mux_set(ADC_GND_ENABLE, IO_FUNC0);
- gpio_pin_set_dir(ADC_GND_ENABLE , GPIO_DIR_OUT, 1);
-// io_open_drain_set(ADC_GND_ENABLE, 1);
- io_pull_set(ADC_GND_ENABLE,IO_HIGH_Z,IO_PULL_UP_NONE);//3
+void LED_output_init(void)
+{
+ //LEDgpio控制
+ io_pin_mux_set(WS2812_PIN, IO_FUNC0);
+ gpio_pin_set_dir(WS2812_PIN , GPIO_DIR_OUT, 0);
+ io_pull_set(WS2812_PIN,IO_HIGH_Z,IO_PULL_UP_NONE);//3
}
void board_configure(void)
@@ -495,8 +493,8 @@
uci_tl_resume();
#else
// button - restore interrupt type
- gpio_enable_irq(_4G_USART_RX_Pin, GPIO_IRQ_TYPE_FALLING_EDGE, _4Gusart_irq_handler);
- gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
+ gpio_enable_irq(PCA_INPUT_DETECT, GPIO_IRQ_TYPE_RISING_EDGE, pca_input_detect_irq_handler);
+// gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
// if (button_irq_handler)
// {
// gpio_enable_irq(BOARD_SW_1, GPIO_IRQ_TYPE_FALLING_EDGE, button_irq_handler);
--
Gitblit v1.9.3