From 82250eaf568648839e4c8fe3f91445347f19c56d Mon Sep 17 00:00:00 2001
From: yincheng.zhong <634916154@qq.com>
Date: 星期一, 23 九月 2024 17:53:46 +0800
Subject: [PATCH] 1H上传测试成功，平均功耗0.7ma，GPS工作时，不能进休眠
---
keil/include/board/board.c | 27 ++++++++++++++++-----------
1 files changed, 16 insertions(+), 11 deletions(-)
diff --git a/keil/include/board/board.c b/keil/include/board/board.c
index 14c5b02..41f1324 100644
--- a/keil/include/board/board.c
+++ b/keil/include/board/board.c
@@ -62,7 +62,7 @@
struct BOARD_PARAM_T board_param = {0};
static GPIO_IRQ_HANDLER_T button_irq_handler = NULL;
static GPIO_IRQ_HANDLER_T accelerate_irq_handler=NULL;
-static GPIO_IRQ_HANDLER_T _4Gusart_irq_handler=NULL;
+ GPIO_IRQ_HANDLER_T _4Gusart_irq_handler=NULL;
extern struct UART_CFG_T test_uart_cfg;
void board_clock_run(void)
{
@@ -108,8 +108,8 @@
trace_open(port, TRACE_BAUD_RATE);
user_trace_port = port;
#endif
- LOG_INFO(TRACE_MODULE_APP, "Hello from MKSEMI!\r\n");
- LOG_INFO(TRACE_MODULE_APP, "Build information %s\r\n", mk_build_inf);
+// LOG_INFO(TRACE_MODULE_APP, "Hello from MKSEMI!\r\n");
+// LOG_INFO(TRACE_MODULE_APP, "Build information %s\r\n", mk_build_inf);
}
void board_calibration_params_default(void)
@@ -402,7 +402,7 @@
{
accelerate_irq_handler=irq_handler;
gpio_pin_set_dir(ACCLERATE_DETECT_Pin , GPIO_DIR_IN, 0);
- io_pull_set(ACCLERATE_DETECT_Pin, IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
+ io_pull_set(ACCLERATE_DETECT_Pin, IO_PULL_DOWN, IO_PULL_UP_NONE);
gpio_enable_irq(ACCLERATE_DETECT_Pin, GPIO_IRQ_TYPE_RISING_EDGE, accelerate_irq_handler);
}
void board_4GUsart_detection_init(GPIO_IRQ_HANDLER_T irq_handler) //4G 串口输入检测中断，下拉触发
@@ -412,6 +412,7 @@
gpio_pin_set_dir(_4G_USART_RX_Pin , GPIO_DIR_IN, 0);
io_pull_set(_4G_USART_RX_Pin, IO_PULL_UP, IO_PULL_UP_LEVEL2);
gpio_enable_irq(_4G_USART_RX_Pin, GPIO_IRQ_TYPE_FALLING_EDGE, _4Gusart_irq_handler);
+ power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)_4G_USART_RX_Pin, POWER_WAKEUP_LEVEL_LOW);
}
void board_button_init(GPIO_IRQ_HANDLER_T irq_handler)
{
@@ -454,19 +455,23 @@
board_led_off(BOARD_LED_1);
#endif
}
-
+extern volatile int32_t m_EUART_DMA_RXPtr;
+extern void _4gUsart_handler(enum IO_PIN_T pin);
void board_restore_from_power_down(void)
{
- uart_open(UART_ID1, &test_uart_cfg);
-
+
+ //uart_open(UART_ID1, &test_uart_cfg);
+ AIR780EUartInit();
+ m_EUART_DMA_RXPtr = 0;
#if defined(UCI_INTF_PORT)
uci_tl_resume();
#else
// button - restore interrupt type
- if (button_irq_handler)
- {
- gpio_enable_irq(BOARD_SW_1, GPIO_IRQ_TYPE_FALLING_EDGE, button_irq_handler);
- }
+ gpio_enable_irq(_4G_USART_RX_Pin, GPIO_IRQ_TYPE_FALLING_EDGE, _4Gusart_irq_handler);
+// if (button_irq_handler)
+// {
+// gpio_enable_irq(BOARD_SW_1, GPIO_IRQ_TYPE_FALLING_EDGE, button_irq_handler);
+// }
#endif
#if !defined(CELL_PHONE_EN)
--
Gitblit v1.9.3