From 9bd738443a77409f46f3447d46b3fa5f91b31309 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期一, 21 七月 2025 16:10:17 +0800
Subject: [PATCH] 增加读取时串口0回包引脚控制逻辑
---
keil/include/main/main.c | 528 +++++++++++++++++++++++++++++-----------------------------
1 files changed, 261 insertions(+), 267 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 8184386..c687682 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -61,10 +61,13 @@
#include "HIDO_ATLite.h"
#include "HIDO_Timer.h"
#include "TCPClient.h"
+#include "PCA9555.h"
+#include "WS2812.h"
-//#define DEBUG_MODE
+#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
+void uart_change_check(uint16_t gpio_state);
#define TEST_UART_POLL_MODE 0
#define TEST_UART_INTERUPT_MODE 1
#define TEST_UART_DMA_MODE 2
@@ -90,14 +93,19 @@
int16_t fVoltage_mv,first_search_flag;
uint8_t bat_percent,g_start_send_flag=1;
uint8_t link_success_flag,motor_count;
-uint16_t gps_wait_count;
+uint16_t gps_wait_count,gps_wait_count2;
uint8_t state5v = 1;
uint8_t motor_power_state=1,uwb_state,air780_power_state,gps_success_state,red_charge_state,green_charge_state,air780_success_state,first_motor_in_flag;
float nomove_count=0;
static uint32_t sample[NUM_SAMPLES] = {0};
-uint8_t recev_error_num,send_messgae_count,send_flag,control_state;
+uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1; //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
+extern uint8_t pca9555writedata_config[10];//暂存寄存器所有配置的数组
+extern uint8_t pca9555writedata_output[10];//暂存输出高低电平配置的数组
+extern uint8_t pca9555writedata_input[10];//暂存输入寄存器所有配置的数组
+extern uint8_t pca9555writedata_polarity[10];//暂存输入极性反转寄存器所有配置的数组
+uint8_t temp_pca9555writedata_input[10];//暂存上一次输入寄存器所有配置的数组
typedef enum
{ UN_BIND=0,
LINK_SUCCESS,
@@ -143,9 +151,27 @@
.int_tx = false,
#endif
};
-void uart_receive_callback(void *dev, uint32_t err_code)
+void uart0_receive_callback(void *dev, uint32_t err_code)
{
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
+}
+void uart1_receive_callback(void *dev, uint32_t err_code)
+{
+ uart_receive(UART_ID1,m_EUART1_DMA_RXBuf,EUART1_RX_BUF_SIZE,uart1_receive_callback);
+}
+void mcu_deep_sleep(void)
+{
+ uint32_t lock;
+ trace_flush();
+ lock = int_lock();
+ LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
+ gps_air780_power_change(0,0);//关闭gps，4G
+ sleep_timer_stop();
+ //adc_close();
+ power_enter_power_down_mode(1);
+ //LOG_INFO(TRACE_MODULE_APP, "进入深度休眠\r\n");
+ sys_reset(0);
+ int_unlock(lock);
}
static void adc_callback(void *data, uint32_t number)
{
@@ -169,129 +195,114 @@
bat_percent = ((fVoltage_mv - 3300) /8);
}
}
- gpio_pin_set(ADC_GND_ENABLE);//在拉高
+ if(fVoltage_mv<3300)
+ {
+ //power_low_flag=1;
+ //gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G
+ LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
+ }else{
+ //power_low_flag=0;
+ //gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
+ LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
+ }
+ PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
// LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
-//void UartInit(void)
-//{
-//board_pins_config();
-//uart_open(UART_ID1, &test_uart_cfg);
-//board_debug_console_open(TRACE_PORT_UART0);
-//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-//}
-extern uint8_t gps_uwb_flag;
-uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state,deep_sleep_flag;
+extern uint8_t gps_uwb_flag,gps_need_data_flag;
+uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
-uint32_t keystarttime,keystarttime2;
-void MotorPoll(void)
-{
- if(UWB_work_state==UN_BIND) {
- gps_uwb_flag=0;//关闭GPS
- moter_open_uwb_flag=0;//关闭震动
- need_open_gps_count=0;//清0计数gps
- } else { //绑定状态下
- if(anchordata_num==1) {
- if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
- fenli_alarm_count = 0;
- if(flag_fenli_alarm)
- {
- flag_fenli_alarm = 0;
- fenli_alarm_count = 0;
- _4GAlarmUpload(2);
- }
- }
- }
- if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
- {
- if(fenli_alarm_count++>20)
- {
- if(!flag_fenli_alarm)
- {
- flag_fenli_alarm = 1;
- _4GAlarmUpload(1);
- }
- }
- }
- if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
- if(flag_alam_state)
- {
- flag_alam_state = 0;
+uint32_t keystarttime,keystarttime2,keystarttime3;
+extern uint32_t get_in_num,get_out_num;
+uint8_t flag_4G_recdata;
- }
-
- need_open_gps_count=0;
- moter_open_uwb_flag=0;//关闭震动
- gps_uwb_flag=0;//关闭GPS
- } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
- need_open_gps_count++;
- moter_open_uwb_flag=1;//开启震动
- if(need_open_gps_count>=20) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- gps_uwb_flag=1;//开启gps测距流程
- need_open_gps_count=0;
- }
- } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
- need_open_gps_count++;
- moter_open_uwb_flag=1;//开启震动
- if(need_open_gps_count>=20) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- gps_uwb_flag=1;//开启gps测距流程
- need_open_gps_count=0;
- }
-
- }
- if(anchordata_num==0) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- distance = 0x1ffff;
- gps_uwb_flag=1;//开启gps测距流程
- moter_open_uwb_flag=1;//开启震动
- need_open_gps_count=0;
- }
- }
- }
void IMUTask(void)
{
-if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
- {
- deep_sleep_flag=1;
- }else{
- deep_sleep_flag=0;
- }
+ if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
+ {//power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
+ mcu_deep_sleep();
+ }
}
void UserKeyTask(void)
- {
- if(!GET_USERKEY)
+{
+if(!read_userkey_input_pca())
{
- if(HIDO_TimerGetTick() - keystarttime>3)
+ if(HIDO_TimerGetTick() - keystarttime3>2)
{
userkey_state = 1;
- keystarttime = HIDO_TimerGetTick();
- UDPClient_UploadGPS();
+ keystarttime3 = HIDO_TimerGetTick();
+ //UDPClient_UploadGPS();
}
- if(HIDO_TimerGetTick() - keystarttime2>10)
+// if(HIDO_TimerGetTick() - keystarttime2>10)
+// {
+//
+// g_com_map[CNT_RESTART] = 1;
+// }
+ }else
+ {
+ keystarttime3 = HIDO_TimerGetTick();
+ }
+}
+void PowerTask(void)
+{
+ if(read_powerkey_input_pca())
+ {
+ if(HIDO_TimerGetTick() - keystarttime>2)
{
- g_com_map[CNT_RESTART] = 1;
+ keystarttime = HIDO_TimerGetTick();
+ PCA9555_Set_One_Value_Output(PWR_ENABLE,0);//低电平关闭
+ PCA9555_Set_One_Value_Output(GPS_LED,0);//输出低电平关闭LED
}
+// if(HIDO_TimerGetTick() - keystarttime2>10)
+// {
+//
+// g_com_map[CNT_RESTART] = 1;
+// }
}else
{
keystarttime = HIDO_TimerGetTick();
keystarttime2 = HIDO_TimerGetTick();
}
- }
+}
void MinuteTask(void)
-{ gpio_pin_clr(ADC_GND_ENABLE);//拉低
+{
+ PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
+void Air780eTask(void)
+{
+// if(!power_low_flag)//确认是否休眠下才开启功能
+// {
+ if(flag_TCP_reconnectting||IfTCPConnected())
+ {
+// // LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
+//
+//// if(flag_4guart_needinit)
+//// {
+//// flag_4guart_needinit = 0;
+//// AIR780EUartInit();
+//// }//yuan
+ if(flag_4G_recdata==1)
+ {
+ flag_4G_recdata = 2;
+
+ //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
+ Socket_RecvAll();
+ }
+ Internet_Poll();
+ HIDO_ATLitePoll();
+ HIDO_TimerPoll();
+ TCPClient_Poll();
+
+ }
+// }
+
+}
+#define BIND_COUNT_NUM 50
+uint8_t bind_flag;
+int8_t bind_count=BIND_COUNT_NUM;
+extern uint8_t find_flag;
+uint8_t poll_count,poll_flag;
void SecondTask(void)
{static uint8_t second_count;
if(second_count++>60)
@@ -299,12 +310,20 @@
second_count = 0;
MinuteTask();
}
- //UWB更新列表
- TagListUpdate();
- Gps_change();
- //GPS_Poll();
- //UWB状态检测
-
+ poll_flag=1;
+// if(bind_flag)
+// {
+// if(bind_count--<=0)
+// {
+// bind_count=BIND_COUNT_NUM;
+// copy_taglist_to_flash();
+// sys_reset(0);
+// bind_flag=0;
+// }
+// }
+// //UWB状态检测
+//if(!power_low_flag)//低供电下不需要检测重连
+// {
if(IfTCPConnected())
{
TCP_reconnect_timer =0;
@@ -322,46 +341,58 @@
}
}
+// }
HIDO_TimerTick();
+ if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
nomove_count++;
+ else{
+ nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
+ }
}
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
+
+void check_input_change(void)
+{
+ uint16_t gpio_state;
+ gpio_state=(uint16_t)pca9555writedata_input[0]<<8|pca9555writedata_input[1];
+ if(WAKE_UP_POSITION&gpio_state)
+ {
+ nomove_count=0;
+ }
+ if(!(MAIN_RI_POSITION&gpio_state))
+ {
+ flag_4G_recdata = 1;
+ delaysleep_count = 3;
+ }
+ //uart_change_check(gpio_state);
+}
+
static void sleep_timer_callback(void *dev, uint32_t time)
{
- // IO_control_init();
- if(enbale_blink_flag)
- {
- green_charge_state=0;
- charge_red_on();
- }
- charge_state_change();//充电状态判断
+
if(secondtask_count++%2==0)
{
flag_secondtask = 1;
}else{
flag_secondtask = 0;
}
- if(enbale_blink_flag)
- {
- green_charge_state=0;
- charge_red_off();
- }
if(delaysleep_count>0)
delaysleep_count--;
//GPS工作逻辑
}
-static void voltage_input_handler(enum IO_PIN_T pin)
+//static void move_handler(enum IO_PIN_T pin)
+//{
+// nomove_count=0;
+//}
+static void pca_handler(enum IO_PIN_T pin)
{
+ PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
+ check_input_change();
+}
-}
-static void move_handler(enum IO_PIN_T pin)
-{
- nomove_count=0;
-}
-uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
{
//LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
@@ -371,29 +402,27 @@
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
+extern uint16_t bind_distance,button_determinate_distance,change_by_frequency_distance;
+extern uint8_t tag_near_frequency;
void Program_Init(void)
{
- Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
+ Usart1ParseDataCallback = Usart1ParseDataHandler;//需改为默认为gps处理，Usart1ParseDataHandler为升级处理当调试时候改为
+ Usart0ParseDataCallback=Usart0ParseDataHandler;
parameter_init_anchor();//g_com_map表初始化角色默认为基站
dev_id=g_com_map[DEV_ID];//这里不太对
group_id=g_com_map[GROUP_ID];//组ID
-// tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
-// g_com_map[ALARM_DISTANCE1] = 40;
-// g_com_map[ALARM_DISTANCE2] = 40;
- warning_distance=g_com_map[ALARM_DISTANCE1];
- prewarning_distance=g_com_map[ALARM_DISTANCE2];
- send_struct.warnDistence=warning_distance;
- send_struct.alarmDistence=prewarning_distance;//更新报警距离
- memcpy(&send_struct.gunLableId,&g_com_map[BIND_DEV_ID],2);//更新绑定ID
- send_struct.tagId=dev_id;//更新设备ID
-
+ memcpy(&bind_distance,&g_com_map[BIND_DISTANCE],2);
+ memcpy(&button_determinate_distance,&g_com_map[DETERMINATION_DISTANCE],2);//设定开关判断距离
+ memcpy(&tag_near_frequency,&g_com_map[NERA_FREQUENCY],1);//设定附近HZ数
+ memcpy(&change_by_frequency_distance,&g_com_map[FREQUENCY_DISTANCE],2);//设定修改HZ生效默认范围
if(g_com_map[BIND_DEV_ID]==0)
{
UWB_work_state = UN_BIND;
}else{
UWB_work_state = SEARCH_DEV;
}
+ //g_com_map[SEND_4G_SECOND]
if(g_com_map[SEND_4G_SECOND]<30)
{
gps_open_flag=0;
@@ -407,31 +436,30 @@
ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
port = g_com_map[TCP_PORT];
- g_com_map[VERSION] = (1<<8)|10;
+ g_com_map[VERSION] = (1<<8)|0;
+ gpio_pin_set(CHANGE_UART_PIN);//；拉高打印输出
LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
- LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-4G车载手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+ LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_无感闸机 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
+ while(uart_tx_in_progress(UART_ID0));
+ gpio_pin_clr(CHANGE_UART_PIN);//；拉低输入
+
}
-
-void IdleTask(void)
+void uart_change_check(uint16_t gpio_state)
{
- if(gpio_pin_get_val(INPUT_5V_Pin))
- {
-
- if(state5v==0)
+ if(INPUT_5V_POSITION&gpio_state)
+ {
+ if(state5v==0)
{
state5v=1;
state5V_prase_flag=state5v;
gps_prase_flag=0;//解除gps解析
uart1_change_from_gps_to_debug();//测试
- // uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
- //UartInit();
- }
-
- //UART_CheckSend();
- } else {
+ PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
+ }
+ }else {
if(state5v==1)
{
g_com_map[MODBUS_MODE] = 0;
@@ -439,32 +467,35 @@
state5V_prase_flag=state5v;
gps_prase_flag=1;//恢复gps解析
uart1_change_from_debug_to_gps();//测试
- // uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
- //UartDeinit();
+ PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
}
- }
+ }
+}
+void IdleTask(void)
+{
+//if(read_5v_input_pca())
+// {
+// if(state5v==0)
+// {
+// state5v=1;
+// state5V_prase_flag=state5v;
+// gps_prase_flag=0;//解除gps解析
+// uart1_change_from_gps_to_debug();//测试
+// PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
+// }
+// }else {
+// if(state5v==1)
+// {
+// g_com_map[MODBUS_MODE] = 0;
+// state5v=0;
+// state5V_prase_flag=state5v;
+// gps_prase_flag=1;//恢复gps解析
+// uart1_change_from_debug_to_gps();//测试
+// PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
+// }
+// }
+ UART0_CheckReceive();
UART_CheckReceive();
-}
-int bind_check(void)
-{
- if(g_com_map[BIND_DEV_ID]!=0x00)
- {
- return 1;
-//绑定信息为1说明设备已经被下发绑定
- } else {
- return 0;
-//绑定信息为0说明设备未被绑定
- }
-}
-void check_if_in_search(void)
-{
- if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
- UWB_work_state=LINK_SUCCESS;
- } else { //否则进入搜索模式
- UWB_work_state=SEARCH_DEV;
- if(first_search_flag==0)
- first_search_flag=1;
- }
}
void boot_deinit(void)
{
@@ -480,35 +511,37 @@
}
uint8_t flag_4guart_needinit=0;
uint8_t index1,index2,index3;
-
+int16_t Voltage_input;
int tt2;
int test1,test3;
uint32_t test4;
-
+#define SLEEP_TIMER_NUM 1000
int main(void)
{
board_clock_run();
boot_deinit();
board_pins_config();
- board_debug_console_open(TRACE_PORT_UART1);
+ board_debug_console_open_baud(TRACE_PORT_UART0,BAUD_115200);
// Reset reason
reset_cause_get();
reset_cause_clear();
+//注意串口一波特率改为9600了为了能和GPS通信上
+// // Load calibration parameters from NVM
+// uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
+// uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
+// if (internal_flash || external_flash == 1)
+// {
+// WsfNvmInit();
+// board_calibration_params_load();
+// flash_close(FLASH_ID0);
+// }
+// else
+// {
+// board_calibration_params_default();
+// }
- // Load calibration parameters from NVM
- uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
- uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
- if (internal_flash || external_flash == 1)
- {
- WsfNvmInit();
- board_calibration_params_load();
- flash_close(FLASH_ID0);
- }
- else
- {
- board_calibration_params_default();
- }
-
+ // Load calibration parameters
+ board_calibration_params_load();
// Chip calibration
calib_chip();
@@ -518,80 +551,42 @@
// open system timer
//sys_timer_open();
-
- // TODO 4G
- Uart_Register(UART_ID_4G, UART_ID0);
- Internet_Init();
- TCPClient_Init();
-
gpio_open();
- board_output_init();//配置adcGND引脚
+ LED_output_init();//配置串口控制脚
+
adc_open(&usr_adc_cfg);
-
- IIC2_Init();
- Accelerometer_Init();
- IO_control_init();
- io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
- gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
- io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
- gps_air780_power_change(0,1);//开启gps，4G
-//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
- gpio_pin_clr(ADC_GND_ENABLE);
- adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
+
Program_Init();
- //uart_open(UART_ID1, &test_uart_cfg);
-
- // uart1_change_from_gps_to_debug();
- //Uart1GpsRecDebugSend();
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-
-// Initialize low power mode
- power_init();
- AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
- sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
- sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
- // board_5V_input_init(voltage_input_handler);
- board_acceleration_detection_init(move_handler);
-// LOG_INFO(TRACE_MODULE_APP, "测试进入app");
- board_4GUsart_detection_init(_4gUsart_handler);
+ uart_open(UART_ID1, &test_uart_cfg);
+ uart_receive(UART_ID1,m_EUART1_DMA_RXBuf,EUART1_RX_BUF_SIZE,uart1_receive_callback);
+ uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
+ // Initialize low power mode
+ power_init();
+ sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
+ sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
+ adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
+ uwb_open();
+ Anchor_uwb_aoa_square_init();
+
+ OpenUWB();
while (1)
- { test4=gpio_pin_get_val(SCL_PIN);
-// if(!deep_sleep_flag)//确认是否休眠下才开启功能
-// {
- if(flag_TCP_reconnectting||IfTCPConnected())
- {
- // LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
-
-// if(flag_4guart_needinit)
-// {
-// flag_4guart_needinit = 0;
-// AIR780EUartInit();
-// }//yuan
- if(flag_4G_recdata==1)
- {
- flag_4G_recdata = 2;
-
- //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
- Socket_RecvAll();
- }
-// air780_led_on();
- Internet_Poll();
- HIDO_ATLitePoll();
- HIDO_TimerPoll();
- TCPClient_Poll();
-// air780_led_off();
- }
-// }
+ {
+ uwb_app_poll();
+ if(poll_flag)
+ {
+ CloseUWB();//关闭接收
+ Tag_uwb_aoa_square_init();
+ TagRange(); //做标签
+ Anchor_uwb_aoa_square_init();
+ poll_flag=0;
+ OpenUWB();
+ }
if(flag_secondtask)
{
flag_secondtask = 0;
SecondTask();
-
}
- UserKeyTask();
- IMUTask();
IdleTask();
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
@@ -615,22 +610,21 @@
// }//yuan
if(delaysleep_count==0)
- if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())))
+ if(!gps_power_state&&!gpio_pin_get_val(INPUT_5V_Pin)&&((IfTCPConnected()&&AIR780E_IsIPIdle()&&Socket_IsSendQueueEmpty(0))||((!flag_TCP_reconnectting)&&!IfTCPConnected())||power_low_flag))
{
// test1=gpio_pin_get_val(_4G_USART_RX_Pin);
uint32_t lock;
//flag_4guart_needinit = 1;
- Internet_Poll();
- HIDO_ATLitePoll();
- HIDO_TimerPoll();
- TCPClient_Poll();
- // power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)_4G_USART_RX_Pin, POWER_WAKEUP_LEVEL_LOW);
+// Internet_Poll();
+// HIDO_ATLitePoll();
+// HIDO_TimerPoll();
+// TCPClient_Poll();
// delay_us(300000);
trace_flush();
lock = int_lock();
power_enter_power_down_mode(0);
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID1,m_EUART1_DMA_RXBuf,EUART1_RX_BUF_SIZE,uart1_receive_callback);
// test3=gpio_pin_get_val(_4G_USART_RX_Pin);
//LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
int_unlock(lock);
--
Gitblit v1.9.3