From 9bd738443a77409f46f3447d46b3fa5f91b31309 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期一, 21 七月 2025 16:10:17 +0800
Subject: [PATCH] 增加读取时串口0回包引脚控制逻辑
---
keil/include/main/main.c | 429 ++++++++++++++++++++---------------------------------
1 files changed, 160 insertions(+), 269 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 233a8b8..c687682 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -136,7 +136,7 @@
.flow = UART_FLOW_CONTROL_NONE,
.rx_level = UART_RXFIFO_CHAR_1,
.tx_level = UART_TXFIFO_EMPTY,
- .baud = BAUD_9600,
+ .baud = BAUD_115200,
#if (TEST_UART_MODE == TEST_UART_POLL_MODE)
.dma_en = false,
.int_rx = false,
@@ -151,9 +151,13 @@
.int_tx = false,
#endif
};
-void uart_receive_callback(void *dev, uint32_t err_code)
+void uart0_receive_callback(void *dev, uint32_t err_code)
{
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
+}
+void uart1_receive_callback(void *dev, uint32_t err_code)
+{
+ uart_receive(UART_ID1,m_EUART1_DMA_RXBuf,EUART1_RX_BUF_SIZE,uart1_receive_callback);
}
void mcu_deep_sleep(void)
{
@@ -195,107 +199,27 @@
{
//power_low_flag=1;
//gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G
- //LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
+ LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
}else{
//power_low_flag=0;
//gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
- //LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
+ LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
}
PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
// LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
-//void UartInit(void)
-//{
-//board_pins_config();
-//uart_open(UART_ID1, &test_uart_cfg);
-//board_debug_console_open(TRACE_PORT_UART0);
-//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-//}
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2,keystarttime3;
extern uint32_t get_in_num,get_out_num;
-void MotorPoll(void)
-{
- if(UWB_work_state==UN_BIND) {
- gps_uwb_flag=0;//关闭GPS
- moter_open_uwb_flag=0;//关闭震动
- need_open_gps_count=0;//清0计数gps
- } else { //绑定状态下
- if(anchordata_num==1) {
- if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
- fenli_alarm_count = 0;
- if(flag_fenli_alarm)
- {
- flag_fenli_alarm = 0;
- fenli_alarm_count = 0;
- _4GAlarmUpload(2);
- }
- }
- }
- if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
- {
- if(fenli_alarm_count++>20)
- {
- if(!flag_fenli_alarm)
- {
- flag_fenli_alarm = 1;
- _4GAlarmUpload(1);
- }
- }
- }
- if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
- if(flag_alam_state)
- {
- flag_alam_state = 0;
+uint8_t flag_4G_recdata;
- }
-
- need_open_gps_count=0;
- moter_open_uwb_flag=0;//关闭震动
- gps_uwb_flag=0;//关闭GPS
- } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
- need_open_gps_count++;
- moter_open_uwb_flag=1;//开启震动
- if(need_open_gps_count>=20) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- gps_uwb_flag=1;//开启gps测距流程
- need_open_gps_count=0;
- }
- } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
- need_open_gps_count++;
- moter_open_uwb_flag=1;//开启震动
- if(need_open_gps_count>=20) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- gps_uwb_flag=1;//开启gps测距流程
- need_open_gps_count=0;
- }
-
- }
- if(anchordata_num==0) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- distance = 0x1ffff;
- gps_uwb_flag=1;//开启gps测距流程
- moter_open_uwb_flag=1;//开启震动
- need_open_gps_count=0;
- }
- }
- }
void IMUTask(void)
{
if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
- {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
+ {//power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
mcu_deep_sleep();
}
}
@@ -345,6 +269,40 @@
PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
+void Air780eTask(void)
+{
+// if(!power_low_flag)//确认是否休眠下才开启功能
+// {
+ if(flag_TCP_reconnectting||IfTCPConnected())
+ {
+// // LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
+//
+//// if(flag_4guart_needinit)
+//// {
+//// flag_4guart_needinit = 0;
+//// AIR780EUartInit();
+//// }//yuan
+ if(flag_4G_recdata==1)
+ {
+ flag_4G_recdata = 2;
+
+ //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
+ Socket_RecvAll();
+ }
+ Internet_Poll();
+ HIDO_ATLitePoll();
+ HIDO_TimerPoll();
+ TCPClient_Poll();
+
+ }
+// }
+
+}
+#define BIND_COUNT_NUM 50
+uint8_t bind_flag;
+int8_t bind_count=BIND_COUNT_NUM;
+extern uint8_t find_flag;
+uint8_t poll_count,poll_flag;
void SecondTask(void)
{static uint8_t second_count;
if(second_count++>60)
@@ -352,37 +310,37 @@
second_count = 0;
MinuteTask();
}
- //UWBOneSecondTask();
-// if(!power_low_flag)
-// Gps_change();
-// else{
-// gps_power_state=0;//关闭GPS
-// update_led_power_state();
-// //初始化GPS计数数据
-// gps_need_data_flag=1;
-// gps_wait_count2=0;
-// gps_wait_count=0;
+ poll_flag=1;
+// if(bind_flag)
+// {
+// if(bind_count--<=0)
+// {
+// bind_count=BIND_COUNT_NUM;
+// copy_taglist_to_flash();
+// sys_reset(0);
+// bind_flag=0;
// }
+// }
// //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
// {
-// if(IfTCPConnected())
-// {
-// TCP_reconnect_timer =0;
-// flag_TCP_reconnectting = 0;
-// } else {
-// if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
-// {
-// flag_TCP_reconnectting = 1;
-// } else {
-// flag_TCP_reconnectting = 0;
-// }
-// if(TCP_reconnect_timer++>600)
-// {
-// TCP_reconnect_timer = 0;
-// }
+ if(IfTCPConnected())
+ {
+ TCP_reconnect_timer =0;
+ flag_TCP_reconnectting = 0;
+ } else {
+ if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
+ {
+ flag_TCP_reconnectting = 1;
+ } else {
+ flag_TCP_reconnectting = 0;
+ }
+ if(TCP_reconnect_timer++>600)
+ {
+ TCP_reconnect_timer = 0;
+ }
-// }
+ }
// }
HIDO_TimerTick();
if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
@@ -403,10 +361,17 @@
{
nomove_count=0;
}
+ if(!(MAIN_RI_POSITION&gpio_state))
+ {
+ flag_4G_recdata = 1;
+ delaysleep_count = 3;
+ }
//uart_change_check(gpio_state);
}
+
static void sleep_timer_callback(void *dev, uint32_t time)
{
+
if(secondtask_count++%2==0)
{
flag_secondtask = 1;
@@ -418,16 +383,16 @@
//GPS工作逻辑
}
-static void move_handler(enum IO_PIN_T pin)
-{
- nomove_count=0;
-}
+//static void move_handler(enum IO_PIN_T pin)
+//{
+// nomove_count=0;
+//}
static void pca_handler(enum IO_PIN_T pin)
{
PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
check_input_change();
}
-uint8_t flag_4G_recdata;
+
void _4gUsart_handler(enum IO_PIN_T pin)
{
//LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
@@ -437,23 +402,20 @@
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
+extern uint16_t bind_distance,button_determinate_distance,change_by_frequency_distance;
+extern uint8_t tag_near_frequency;
void Program_Init(void)
{
- Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
+ Usart1ParseDataCallback = Usart1ParseDataHandler;//需改为默认为gps处理，Usart1ParseDataHandler为升级处理当调试时候改为
+ Usart0ParseDataCallback=Usart0ParseDataHandler;
parameter_init_anchor();//g_com_map表初始化角色默认为基站
dev_id=g_com_map[DEV_ID];//这里不太对
group_id=g_com_map[GROUP_ID];//组ID
-// tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
-// g_com_map[ALARM_DISTANCE1] = 40;
-// g_com_map[ALARM_DISTANCE2] = 40;
- warning_distance=g_com_map[ALARM_DISTANCE1];
- prewarning_distance=g_com_map[ALARM_DISTANCE2];
- send_struct.warnDistence=warning_distance;
- send_struct.alarmDistence=prewarning_distance;//更新报警距离
- memcpy(&send_struct.gunLableId,&g_com_map[BIND_DEV_ID],2);//更新绑定ID
- send_struct.tagId=dev_id;//更新设备ID
-
+ memcpy(&bind_distance,&g_com_map[BIND_DISTANCE],2);
+ memcpy(&button_determinate_distance,&g_com_map[DETERMINATION_DISTANCE],2);//设定开关判断距离
+ memcpy(&tag_near_frequency,&g_com_map[NERA_FREQUENCY],1);//设定附近HZ数
+ memcpy(&change_by_frequency_distance,&g_com_map[FREQUENCY_DISTANCE],2);//设定修改HZ生效默认范围
if(g_com_map[BIND_DEV_ID]==0)
{
UWB_work_state = UN_BIND;
@@ -475,9 +437,13 @@
ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
port = g_com_map[TCP_PORT];
g_com_map[VERSION] = (1<<8)|0;
+ gpio_pin_set(CHANGE_UART_PIN);//；拉高打印输出
LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
- LOG_INFO(TRACE_MODULE_APP,"固件版本:4G-GPS定位手环 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+ LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_无感闸机 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
+ while(uart_tx_in_progress(UART_ID0));
+ gpio_pin_clr(CHANGE_UART_PIN);//；拉低输入
+
}
@@ -507,49 +473,29 @@
}
void IdleTask(void)
{
-if(read_5v_input_pca())
- {
- if(state5v==0)
- {
- state5v=1;
- state5V_prase_flag=state5v;
- gps_prase_flag=0;//解除gps解析
- uart1_change_from_gps_to_debug();//测试
- PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
- }
- }else {
- if(state5v==1)
- {
- g_com_map[MODBUS_MODE] = 0;
- state5v=0;
- state5V_prase_flag=state5v;
- gps_prase_flag=1;//恢复gps解析
- uart1_change_from_debug_to_gps();//测试
- PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
- }
- }
+//if(read_5v_input_pca())
+// {
+// if(state5v==0)
+// {
+// state5v=1;
+// state5V_prase_flag=state5v;
+// gps_prase_flag=0;//解除gps解析
+// uart1_change_from_gps_to_debug();//测试
+// PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
+// }
+// }else {
+// if(state5v==1)
+// {
+// g_com_map[MODBUS_MODE] = 0;
+// state5v=0;
+// state5V_prase_flag=state5v;
+// gps_prase_flag=1;//恢复gps解析
+// uart1_change_from_debug_to_gps();//测试
+// PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
+// }
+// }
+ UART0_CheckReceive();
UART_CheckReceive();
-}
-int bind_check(void)
-{
- if(g_com_map[BIND_DEV_ID]!=0x00)
- {
- return 1;
-//绑定信息为1说明设备已经被下发绑定
- } else {
- return 0;
-//绑定信息为0说明设备未被绑定
- }
-}
-void check_if_in_search(void)
-{
- if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
- UWB_work_state=LINK_SUCCESS;
- } else { //否则进入搜索模式
- UWB_work_state=SEARCH_DEV;
- if(first_search_flag==0)
- first_search_flag=1;
- }
}
void boot_deinit(void)
{
@@ -569,31 +515,33 @@
int tt2;
int test1,test3;
uint32_t test4;
-
+#define SLEEP_TIMER_NUM 1000
int main(void)
{
board_clock_run();
boot_deinit();
board_pins_config();
- board_debug_console_open_baud(TRACE_PORT_UART1,BAUD_115200);
+ board_debug_console_open_baud(TRACE_PORT_UART0,BAUD_115200);
// Reset reason
reset_cause_get();
reset_cause_clear();
//注意串口一波特率改为9600了为了能和GPS通信上
- // Load calibration parameters from NVM
- uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
- uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
- if (internal_flash || external_flash == 1)
- {
- WsfNvmInit();
- board_calibration_params_load();
- flash_close(FLASH_ID0);
- }
- else
- {
- board_calibration_params_default();
- }
+// // Load calibration parameters from NVM
+// uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
+// uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
+// if (internal_flash || external_flash == 1)
+// {
+// WsfNvmInit();
+// board_calibration_params_load();
+// flash_close(FLASH_ID0);
+// }
+// else
+// {
+// board_calibration_params_default();
+// }
+ // Load calibration parameters
+ board_calibration_params_load();
// Chip calibration
calib_chip();
@@ -603,99 +551,42 @@
// open system timer
//sys_timer_open();
-
- // TODO 4G
- Uart_Register(UART_ID_4G, UART_ID0);
-// Internet_Init();
-// TCPClient_Init();
-
gpio_open();
- LED_output_init();//配置adcGND引脚
-// battery_monitor_open();
-// Voltage_input=battery_monitor_get();
-// battery_monitor_close();
+ LED_output_init();//配置串口控制脚
adc_open(&usr_adc_cfg);
-
- IIC2_Init();
- Accelerometer_Init();
- PCA9555_init();
- if(!read_5v_input_pca())
- {
- Set4LEDColor(BLUE,GREEN,WHITE,GREEN);
- delay_ms(500);
- Set4LEDColor(RED,WHITE,RED,WHITE);
- delay_ms(500);
- //Set4LEDColor(LEDOFF,LEDOFF,LEDOFF,LEDOFF);
- }
- //IO_control_init();
-// io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
-// gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
-// io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
- //gps_air780_power_change(0,1);//开启gps，4G
-//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
+
Program_Init();
- //uart_open(UART_ID1, &test_uart_cfg);
- // uart1_change_from_gps_to_debug();
- //Uart1GpsRecDebugSend();
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-
-// Initialize low power mode
- power_init();
- //AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
- sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
- sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
- // board_5V_input_init(voltage_input_handler);
- PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
- adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
- board_acceleration_detection_init(move_handler);
- pca_input_detection_init(pca_handler);//pca检测输入
- Uwb_init();
- OpenUWB();
- //board_4GUsart_detection_init(_4gUsart_handler);
+ uart_open(UART_ID1, &test_uart_cfg);
+ uart_receive(UART_ID1,m_EUART1_DMA_RXBuf,EUART1_RX_BUF_SIZE,uart1_receive_callback);
+ uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
+ // Initialize low power mode
+ power_init();
+ sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
+ sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
+ adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
+ uwb_open();
+ Anchor_uwb_aoa_square_init();
+
+ OpenUWB();
while (1)
{
- uwb_app_poll();
-
- //test4=gpio_pin_get_val(SCL_PIN);
- //UWBPoll();
-// if(!power_low_flag)//确认是否休眠下才开启功能
-// {
-// if(flag_TCP_reconnectting||IfTCPConnected())
-// {
-// // LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
-//
-//// if(flag_4guart_needinit)
-//// {
-//// flag_4guart_needinit = 0;
-//// AIR780EUartInit();
-//// }//yuan
-// if(flag_4G_recdata==1)
-// {
-// flag_4G_recdata = 2;
-//
-// //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
-// Socket_RecvAll();
-// }
-//// air780_led_on();
-// Internet_Poll();
-// HIDO_ATLitePoll();
-// HIDO_TimerPoll();
-// TCPClient_Poll();
-//// air780_led_off();
-// }
-// }
+ uwb_app_poll();
+ if(poll_flag)
+ {
+ CloseUWB();//关闭接收
+ Tag_uwb_aoa_square_init();
+ TagRange(); //做标签
+ Anchor_uwb_aoa_square_init();
+ poll_flag=0;
+ OpenUWB();
+ }
if(flag_secondtask)
{
flag_secondtask = 0;
SecondTask();
-
}
- PowerTask();
-// IMUTask();
- UserKeyTask();
IdleTask();
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
@@ -733,7 +624,7 @@
trace_flush();
lock = int_lock();
power_enter_power_down_mode(0);
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID1,m_EUART1_DMA_RXBuf,EUART1_RX_BUF_SIZE,uart1_receive_callback);
// test3=gpio_pin_get_val(_4G_USART_RX_Pin);
//LOG_INFO(TRACE_MODULE_APP, "进入休眠\r\n");
int_unlock(lock);
--
Gitblit v1.9.3