From 97091dac1bfcad87e0e3f8bb3fc718c1254d97d2 Mon Sep 17 00:00:00 2001
From: WXK <287788329@qq.com>
Date: 星期五, 15 八月 2025 13:50:06 +0800
Subject: [PATCH] 2.3，加入下发开关uwb接收
---
keil/include/main/main.c | 691 +++++++++++++++++++++++++++++++++++++++------------------
1 files changed, 475 insertions(+), 216 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 53ab240..b34dd9a 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -40,194 +40,251 @@
#include "mk_trace.h"
#include "mk_wdt.h"
-#include "mk_calib.h"
+#include "mk_reset.h"
+#include "mk_gpio.h"
#include "mk_misc.h"
+#include "mk_sleep_timer.h"
+#include "mk_power.h"
+#include "mk_uwb.h"
+#include "mk_calib.h"
+#include "mk_uart.h"
+#include "mk_spi.h"
#include "mk_flash.h"
-#include "libc_rom.h"
+#include "Usart.h"
#include <serial_at_cmd_app.h>
#include <global_param.h>
+
#include "board.h"
+
+#include "pal_sys.h"
+#include "wsf_os.h"
+#include "wsf_timer.h"
+#include "wsf_buf.h"
#include "wsf_nvm.h"
-#include "mk_power.h"
-#include "mk_sleep_timer.h"
-#include "Usart.h"
-#include "mk_adc.h"
-extern int TagRange(void);
-extern void parameter_init(void);
-uint8_t trx_buf[10] = {0};
-#define TEST_UART_POLL_MODE 0
-#define TEST_UART_INTERUPT_MODE 1
-#define TEST_UART_DMA_MODE 2
-#define TEST_UART_MODE TEST_UART_DMA_MODE
-#define NUM_SAMPLES 1
-#define SLEEP_START_TIME 120
-uint8_t enable_sleep_count,sleep_flag;
-//#define DEBUG_MODE
-struct UART_CFG_T test_uart_cfg =
-{
- .parity = UART_PARITY_NONE,
- .stop = UART_STOP_BITS_1,
- .data = UART_DATA_BITS_8,
- .flow = UART_FLOW_CONTROL_NONE,
- .rx_level = UART_RXFIFO_CHAR_1,
- .tx_level = UART_TXFIFO_EMPTY,
- .baud = BAUD_115200,
-#if (TEST_UART_MODE == TEST_UART_POLL_MODE)
- .dma_en = false,
- .int_rx = false,
- .int_tx = false,
-#elif (TEST_UART_MODE == TEST_UART_INTERUPT_MODE)
- .dma_en = false,
- .int_rx = true,
- .int_tx = true,
-#elif (TEST_UART_MODE == TEST_UART_DMA_MODE)
- .dma_en = true,
- .int_rx = false,
- .int_tx = false,
+#include "app.h"
+#include "ranging_fira.h"
+#include "uwb_api.h"
+#include "lib_ranging.h"
+#include "uci_tl_task.h"
+#include "libc_rom.h"
+
+#ifdef UWB_UCI_TEST_EN
+#include "uwb_test.h"
#endif
- };
-static uint32_t sample[NUM_SAMPLES] = {0};
-static struct ADC_CFG_T usr_adc_cfg = {
- .mode = ADC_MODE_CONTINUE, /* Selected single conversion mode */
- .clk_sel = ADC_CLK_HIGH, /* Selected 62.4M high speed clock */
- .vref_sel = ADC_SEL_VREF_INT, /* Using internal reference voltage (1.2V)*/
- .rate = 500000, /* ADC works at high frequency system clock, the maximum sampling rate is 2M */
- .channel_p = ADC_IN_EXTPIN0, /* ADC positive channel --> GPIO0 */
- .channel_n = ADC_IN_VREF, /* ADC negative channel --> Vref */
- .int_en = false,
- .dma_en = false, /* DMA support only in continue mode */
- .acc_num = 0,
- .high_pulse_time = 4,
- .settle_time = 1,
+#ifdef CELL_PHONE_EN
+#include "mk_efuse.h"
+
+#define EFUSE_FLASH_EN_ADDR (0x67)
+#define EFUSE_FLASH_EN_BIT (0x80)
+
+bool check_flash_bit_of_efuse(void);
+bool program_efuse(void);
+
+bool check_flash_bit_of_efuse(void)
+{
+ uint8_t val;
+ val = efuse_read_byte(EFUSE_FLASH_EN_ADDR);
+ return ((val & EFUSE_FLASH_EN_BIT) ? true : false);
+}
+
+bool program_efuse(void)
+{
+ efuse_program_byte(EFUSE_FLASH_EN_ADDR, EFUSE_FLASH_EN_BIT);
+ if (check_flash_bit_of_efuse())
+ {
+ LOG_INFO(TRACE_MODULE_APP, "Program eFuse INT_FLASH bit successfully.\r\n");
+ return true;
+ }
+ else
+ {
+ LOG_INFO(TRACE_MODULE_APP, "Program eFuse INT_FLASH bit failed.\r\n");
+ return false;
+ }
+ return true;
+}
+#endif
+
+//*****************************************************************************
+//
+// WSF buffer pools.
+//
+//*****************************************************************************
+#define WSF_BUF_POOLS 5
+void Fira_Change_Task(void);
+extern uint8_t normal_flag,log_4g_enable_flag,lora_tx_flag;
+extern uint16_t ip0,ip1,ip2,ip3,port;
+uint8_t group_id,enable_sleep_count;
+uint32_t dev_id;
+uint16_t disoffset;
+uint16_t set_mk_time;
+uint8_t flag_sleeptimer,flag_secondtask,secondtask_count;
+float nomove_count;
+// Default pool descriptor.
+static wsfBufPoolDesc_t poolDescriptors[WSF_BUF_POOLS] = {
+ {32, 26}, {64, 24}, {128, 4}, {256 + 32, 4}, {1024 + 32, 2},
};
-uint8_t state5v = 1;
-uint8_t bat_percent=0,g_start_send_flag=1;
-int16_t fVoltage_mv;
-uint8_t bat_percent;
-extern uint32_t dev_id;
-extern uint8_t group_id;
-uint8_t tag_frequence;
-void UartDeinit(void);
-void UartInit(void);
-void Program_Init(void);
-void IdleTask(void);
-void boot_deinit(void);
-static void uart_receive_callback(void *dev, uint32_t err_code)
-{
-uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-}
-void UartInit(void)
-{
-board_pins_config();
-uart_open(UART_ID1, &test_uart_cfg);
-board_debug_console_open(TRACE_PORT_UART0);
-uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-}
-void UartDeinit(void)
-{
-uart_close(UART_ID0);
-uart_close(UART_ID1);
-}
static void sleep_timer_callback(void *dev, uint32_t time)
{
- //sleep_timer_start(__MS_TO_32K_CNT(1000));
- enable_sleep_count++;
- if(enable_sleep_count==SLEEP_START_TIME){
-
- enable_sleep_count=0;
- sleep_flag=1;
- }
- g_start_send_flag=1;
- //LOG_INFO(TRACE_MODULE_APP, "Sleep timer interrupt callback\r\n");
+ // LOG_INFO(TRACE_MODULE_APP, "Wake up by sleep timer %d\r\n", time);
}
-static void adc_callback(void *data, uint32_t number)
+extern uint8_t start_wait_flag;
+extern int16_t end_count1;
+static void sleep_timer_callback_normal(void *dev, uint32_t time)
{
- uint32_t *result = (uint32_t *)data;
- for (uint16_t i = 0; i < number; i++)
+ if(secondtask_count++%2==0)
{
-// LOG_INFO(TRACE_MODULE_APP, "The voltage measured %d mv\r\n",
-// ADC_INTERNAL_VREF_MV + adc_code_to_mv((int16_t)*result, ADC_INTERNAL_VREF_MV));
- fVoltage_mv=ADC_INTERNAL_VREF_MV + adc_code_to_mv((int16_t)*result, ADC_INTERNAL_VREF_MV);
- fVoltage_mv=fVoltage_mv*2;
- if(fVoltage_mv < 3300)
- {
- bat_percent = 0;
- }
- else if(fVoltage_mv > 4100)
- {
- bat_percent = 100;
- }
- else
- {
- bat_percent = ((fVoltage_mv - 3300) /8);
- }
+ flag_secondtask = 1;
+ }else{
+ flag_secondtask = 0;
}
- LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
-}
-static void voltage_input_handler(enum IO_PIN_T pin)
-{
-//LOG_INFO(TRACE_MODULE_APP, "中断唤醒\r\n");
+ if(start_wait_flag)//lora升级等待超时标志
+ {
+ if(end_count1--<=0)
+ start_wait_flag=0;
+ }
+// if(delaysleep_count>0)
+// delaysleep_count--;
}
void Program_Init(void)
-{
-Usart1ParseDataCallback = UsartParseDataHandler;
-parameter_init();//g_com_map表初始化
-group_id=g_com_map[GROUP_ID];
-memcpy(&dev_id ,&g_com_map[DEV_ID],2);
-tag_frequence=1000/g_com_map[COM_INTERVAL];
-g_com_map[VERSION] = (1<<8)|1;
-LOG_INFO(TRACE_MODULE_APP,"设备ID: %x .\r\n",dev_id);
-LOG_INFO(TRACE_MODULE_APP,"固件版本:UWB-标签 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+{
+ Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
+
+ parameter_init_anchor();//g_com_map表初始化角色默认为基站
+ dev_id=g_com_map[DEV_ID];//这里不太对
+ group_id=(uint8_t)g_com_map[GROUP_ID];//组ID
+// tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
+ memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
+// g_com_map[ALARM_DISTANCE1] = 40;
+// g_com_map[ALARM_DISTANCE2] = 40;
+// warning_distance=g_com_map[ALARM_DISTANCE1];
+// prewarning_distance=g_com_map[ALARM_DISTANCE2];
+ //g_com_map[SEND_4G_SECOND]
+// if(g_com_map[SEND_4G_SECOND]<30)
+// {
+// gps_open_flag=0;
+// }else{
+// gps_open_flag=1;
+// }
+// g_com_map[MODBUS_MODE] = 0;
+ log_4g_enable_flag=g_com_map[LOG_4G_ENABLE];
+ ip0 = (g_com_map[TCP_IP_0]>>12&0xf)*1000+(g_com_map[TCP_IP_0]>>8&0xf)*100+(g_com_map[TCP_IP_0]>>4&0xf)*10+(g_com_map[TCP_IP_0]&0xf);
+ ip1 = (g_com_map[TCP_IP_1]>>12&0xf)*1000+(g_com_map[TCP_IP_1]>>8&0xf)*100+(g_com_map[TCP_IP_1]>>4&0xf)*10+(g_com_map[TCP_IP_1]&0xf);
+ ip2 = (g_com_map[TCP_IP_2]>>12&0xf)*1000+(g_com_map[TCP_IP_2]>>8&0xf)*100+(g_com_map[TCP_IP_2]>>4&0xf)*10+(g_com_map[TCP_IP_2]&0xf);
+ ip3 = (g_com_map[TCP_IP_3]>>12&0xf)*1000+(g_com_map[TCP_IP_3]>>8&0xf)*100+(g_com_map[TCP_IP_3]>>4&0xf)*10+(g_com_map[TCP_IP_3]&0xf);
+ port = g_com_map[TCP_PORT];
+ g_com_map[VERSION] = (2<<8)|3;
+ LOG_INFO(TRACE_MODULE_APP,"设备ID: %x 小组id %d .\r\n",dev_id,g_com_map[GROUP_ID]);
+// if(gpio_pin_get_val(MODE_CHANGE_PIN))
+// LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_Air_tag模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+// else{
+// LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_免布线模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+// }
+ LOG_INFO(TRACE_MODULE_APP,"服务器地址: %d.%d.%d.%d:%d.\r\n",ip0,ip1,ip2,ip3,port);
}
-void IdleTask(void)
-{ UART0_CheckReceive();
- if(gpio_pin_get_val(INPUT_5V_Pin))
- {
-
-
- //UART_CheckSend();
-// bat_percent=Get_Battary();
- if(state5v==0)
- {
- state5v=1;
- }
- }else{
- if(state5v==1)
- {
- state5v=0;
- //UartDeinit();
- }
-
+void MinuteTask(void)
+{
+// adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
}
+/********************************************************************************************************/
+static void Lora_irq_handler(enum IO_PIN_T pin)
+{
+ RadioIrqProcess();
+}
+void SecondTask(void)
+{static uint8_t second_count;
+ if(second_count++>60)
+ {
+ second_count = 0;
+ MinuteTask();
+ }
+ lora_tx_flag=1;
+
+ //Lora_Tx_Poll();
+// //UWB状态检测
+//if(!power_low_flag)//低供电下不需要检测重连
+// {
+// if(IfTCPConnected())
+// {
+// TCP_reconnect_timer =0;
+// flag_TCP_reconnectting = 0;
+// } else {
+// if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
+// {
+// flag_TCP_reconnectting = 1;
+// } else {
+// flag_TCP_reconnectting = 0;
+// }
+// if(TCP_reconnect_timer++>600)
+// {
+// TCP_reconnect_timer = 0;
+// }
+
+// }
+// }
+
+ HIDO_TimerTick();
+ if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
+ nomove_count++;
+ else{
+ nomove_count=g_com_map[NOMOVESLEEP_TIME]+1;
+ }
}
-void boot_deinit(void)
+void spi_init(void)
{
- //将boot中串口返回普通gpio
-// UART0 TX/RX
- io_pin_mux_set(IO_PIN_5, IO_FUNC0);
- io_pin_mux_set(IO_PIN_6, IO_FUNC0);
- // UART1 RX/TX
- io_pin_mux_set(IO_PIN_10, IO_FUNC0);
- io_pin_mux_set(IO_PIN_9, IO_FUNC0);
- uart_close(UART_ID1);//解绑原来串口1
- uart_close(UART_ID0);//解绑原来串口0
+ struct SPI_CFG_T usr_spi_cfg =
+ {
+ .bit_rate = 1000000,
+ .data_bits = 8,
+//#if TEST_SPI_MASTER
+ .slave = 0,
+//#else
+// .slave = 1,
+//#endif
+ .clk_phase = 0,
+ .clk_polarity = 0,
+ .ti_mode = 0,
+//#if (TEST_SPI_MODE == TEST_SPI_POLL_MODE)
+ .dma_rx = false,
+ .dma_tx = false,
+ .int_rx = false,
+ .int_tx = false,
+//#elif (TEST_SPI_MODE == TEST_SPI_INTERUPT_MODE)
+// .dma_rx = false,
+// .dma_tx = false,
+// .int_rx = true,
+// .int_tx = true,
+//#elif (TEST_SPI_MODE == TEST_SPI_DMA_MODE)
+// .dma_rx = true,
+// .dma_tx = true,
+// .int_rx = false,
+// .int_tx = false,
+//#endif
+ };
+
+ spi_open(SPI_ID0, &usr_spi_cfg);
}
-int main(void)
+static void board_init(void)
{
- board_clock_run();
- boot_deinit();
- board_pins_config();
- board_debug_console_open(TRACE_PORT_UART0);
- // Reset reason
- reset_cause_get();
- reset_cause_clear();
- // Load calibration parameters from NVM
uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
+
+ // Clock configuration
+ board_clock_run();
+ boot_deinit();//新加的
+ // Pin configuration
+ board_pins_config();
+ // Trace configuration
+ board_debug_console_open(TRACE_PORT_UART1);
+ // Reset reason
+ reset_cause_get();
+ reset_cause_clear();
+
+#ifndef CELL_PHONE_EN
+ // Load calibration parameters from NVM
if (internal_flash || external_flash == 1)
{
WsfNvmInit();
@@ -238,65 +295,267 @@
{
board_calibration_params_default();
}
-
+#else
+ if (internal_flash)
+ {
+ program_efuse();
+ }
+ board_calibration_params_default();
+#endif
+
// Chip calibration
calib_chip();
- // Disable watchdog timer
- wdt_close(WDT_ID0);
- //LOG_INFO(TRACE_MODULE_APP, "UWB qiang test example\r\n");
-
- // open system timer
- //sys_timer_open();
-
gpio_open();
- //board_led_init();
-
- //uart_open(UART_ID0, &test_uart_cfg);
-
- Program_Init();
- //power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)POWER_WAKEUP_BY_GPIO_0, POWER_WAKEUP_LEVEL_LOW);
- uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
- // Initialize low power mode
- power_init();
- //adc_open(&usr_adc_cfg);
- //adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
- // Enable sleep timer
- sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
- sleep_timer_start(__MS_TO_32K_CNT(500));//测试
- //board_5V_input_init(voltage_input_handler);//有修改3.3V会一直高电平导致无法进入休眠
-// io_pin_mux_set(IO_PIN_5, IO_FUNC0);//波形测试
-// gpio_pin_set_dir( IO_PIN_5, GPIO_DIR_OUT, 0);
-// io_pull_set(IO_PIN_5 , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
- //Serial0_PutString("进入app测试\r\n");
- while (1)
- {
- if(g_start_send_flag)
- {
- //LOG_INFO(TRACE_MODULE_APP, "测距ing");
-
- g_start_send_flag = 0;
-
- TagRange();
- IdleTask();
- }else{
- IdleTask();
- }
-#ifndef DEBUG_MODE
- if(sleep_flag){//开始一段时间无休眠
- trace_flush();
- uint32_t lock = int_lock();
- //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
- //唤醒源设置MK8000修改
- //board_5V_input_init(voltage_input_handler);
- //sleep_timer_start(g_com_map[COM_INTERVAL]);
- power_enter_power_down_mode(0);
- uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
- //LOG_INFO(TRACE_MODULE_APP, "进入低功耗");
- int_unlock(lock);
- }
-#endif
- }
+#ifdef CELL_PHONE_EN
+ // Configure IO_04 for RF Switch
+ gpio_pin_set_dir(IO_PIN_4, GPIO_DIR_OUT, 0);
+#else
+ spi_init();
+// // 模式判断脚和spi nrst脚初始化
+ board_mode_pin_init();
+ Program_Init();
+ //board_led_on(BOARD_LED_1);
+#endif
+ Board_LORA_NVIC_Init(Lora_irq_handler);
+ board_configure();
+}
+
+void app_process_handle(uint8_t msg_id, const void *param)
+{
+ switch (msg_id)
+ {
+ case APP_TEST_TIMER1_MSG:
+ {
+#if ANT_DELAY_CAL_EN
+ // stop calibration
+ uwbapi_session_stop(uwb_app_config.session_id);
+ uwbapi_session_deinit(uwb_app_config.session_id);
+
+ // restart UCI RX
+ uci_tl_rx_restart();
+#endif
+ }
+ break;
+
+ default:
+ break;
+ }
+}
+
+void Fira_Change_Task(void)
+{
+}
+
+static void uart_receive_callback(void *dev, uint32_t err_code)
+{
+ uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+}
+void uart0_receive_callback(void *dev, uint32_t err_code)
+{
+ uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
+}
+uint8_t bat_percent;
+uint8_t stationary_flag;
+extern uint8_t send_flag;
+extern uint8_t txdone;
+void mcu_deep_sleep(void)
+{
+ uint32_t lock;
+ trace_flush();
+
+ lock = int_lock();
+ sleep_timer_stop();
+ power_enter_power_down_mode(1);
+ int_unlock(lock);
+}
+int main(void)
+{
+ // Initialize MCU system
+ board_init();
+ // Disable watchdog timer
+ wdt_close(WDT_ID0);
+ LOG_INFO(TRACE_MODULE_APP, "UCI FiRa example\r\n");
+// delay_ms(500);
+// lora_in_sleep();
+// power_init();
+// mcu_deep_sleep();
+ if(gpio_pin_get_val(SLEEP_PIN))
+// if(1)
+ {
+ if(gpio_pin_get_val(MODE_CHANGE_PIN))//记得改回来与正式的相反
+// if(0)//记得改回来与正式的相反
+ {
+ LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_Air_tag模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+ // Platform init for WSF
+ PalSysInit();
+
+ // Initialize os
+
+ //
+ // Set up timers for the WSF scheduler.
+ //
+ WsfOsInit();
+ WsfTimerInit();
+ sys_tick_callback_set(WsfTimerUpdateTicks);
+
+ //
+ // Initialize a buffer pool for WSF dynamic memory needs.
+ //
+ uint32_t wsfBufMemLen = WsfBufInit(WSF_BUF_POOLS, poolDescriptors);
+
+ if (wsfBufMemLen > FREE_MEM_SIZE)
+ {
+ LOG_INFO(TRACE_MODULE_APP, "Memory pool is not enough %d\r\n", wsfBufMemLen - FREE_MEM_SIZE);
+ }
+//
+ // Create app task
+ //
+ wsfHandlerId_t handlerId = WsfOsSetNextHandler(app_handler);
+ app_init(handlerId);
+
+ //
+ // Create ranging task or test task
+ //
+ handlerId = WsfOsSetNextHandler(ranging_handler);
+ ranging_init(handlerId);
+
+#ifdef UWB_UCI_TEST_EN
+ // Create test task
+ handlerId = WsfOsSetNextHandler(uwb_test_handler);
+ uwb_test_init(handlerId);
+#endif
+
+#ifndef MY_MODE
+ uwb_open();
+
+ // set advanced parameters
+ struct PHY_ADV_CONFIG_T adv_config =
+ {
+ // RPM0: 40, RPM3: 60
+ .thres_fap_detect = 60,
+ // RPM0: 4, RPM3: 8
+ .nth_scale_factor = 8,
+ // RFrame SP0: 0/1, Others: 0/1/2/3
+ .ranging_performance_mode = 3,
+#if RX_ANT_PORTS_NUM == 4
+ .skip_weakest_port_en = 1,
+#else
+ .skip_weakest_port_en = 0,
+#endif
+ };
+ phy_adv_params_configure(&adv_config);
+
+ // which RX ports will be used for AoA/PDoA
+ phy_rx_ant_mode_set(RX_ANT_PORTS_COMBINATION);
+
+ uwbs_init();
+ uwb_app_config.ranging_flow_mode = (uint8_t)(RANGING_FLOW_FIRA);
+ uwb_app_config.filter_en = (uint8_t)(FILTER_EN);
+ uwb_app_config.session_param.tx_power_level = board_param.tx_power_fcc[CALIB_CH(uwb_app_config.ppdu_params.ch_num)];
+ uwb_app_config.ppdu_params.rx_ant_id = (uint8_t)(RX_MAIN_ANT_PORT);
+
+#elif defined MY_MODE
+ Uwb_init();//默认为我们测距配置
+ OpenUWB();
+ uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+#endif
+ //
+ // Create UCI transmission layer task
+ //
+ handlerId = WsfOsSetNextHandler(uci_tl_handler);
+ uci_tl_init(handlerId);
+
+ // Initialize low power mode
+ power_init();
+#if LOW_POWER_EN
+ power_mode_request(POWER_UNIT_USER, POWER_MODE_POWER_DOWN);
+ uwb_app_config.low_power_en = 1;
+#else
+ power_mode_request(POWER_UNIT_USER, POWER_MODE_SLEEP);
+ uwb_app_config.low_power_en = 0;
+#endif
+
+ // Enable sleep timer
+ sleep_timer_open(true, SLEEP_TIMER_MODE_ONESHOT, sleep_timer_callback);
+
+ while (1)
+ {
+ wsfOsDispatcher();
+ power_manage();
+ if(!gpio_pin_get_val(SLEEP_PIN))
+ {
+ delay_ms(300);
+ //LOG_INFO(TRACE_MODULE_APP, "进入休眠模式\r\n");//会打断休眠
+ //gpio_pin_clr(LORA_NRST);//lora休眠
+ //spi_close(SPI_ID0);
+ lora_in_sleep();
+ power_init();
+ mcu_deep_sleep();
+ }
+ }
+ }else{
+ LOG_INFO(TRACE_MODULE_APP,"固件版本:MK_免布线模式 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
+ uart0_Init_normal();
+ Lora_1268_Init();
+ //LOG_INFO(TRACE_MODULE_APP," 切换6\r\n");
+ SwitchLoraSettings(478,7,22);
+ Uwb_init();//默认为我们测距配置
+ if(g_com_map[MODBUS_MODE]==0)
+ {
+ OpenUWB();
+ }
+ if(g_com_map[MODBUS_MODE]==1)
+ {
+ CloseUWB();
+ }
+ uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID0,m_EUART0_DMA_RXBuf,EUART0_RX_BUF_SIZE,uart0_receive_callback);
+ power_init();
+ sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback_normal);
+ sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
+ while (1)
+ {
+ if(send_flag)
+ {
+ LOG_INFO(TRACE_MODULE_APP,"发送数量%d. \r\n",txdone);
+ send_flag=0;
+ }
+ uwb_app_poll();//我们的测距逻辑
+ if(flag_secondtask)
+ {
+ flag_secondtask = 0;
+ SecondTask();
+ //Lora_Tx_Poll();
+ }
+ Lora_Tx_Poll();
+// LoraUp_Poll();//网关升级
+// if(!gpio_pin_get_val(SLEEP_PIN))
+// {
+// delay_ms(300);
+// //LOG_INFO(TRACE_MODULE_APP, "进入休眠模式\r\n");//会打断休眠
+// //gpio_pin_clr(LORA_NRST);//lora休眠
+// //spi_close(SPI_ID0);
+// lora_in_sleep();
+// power_init();
+// mcu_deep_sleep();
+// }
+ IdleTask();
+ }
+ }
+}else{
+
+delay_ms(300);
+ //LOG_INFO(TRACE_MODULE_APP, "进入休眠模式\r\n");//会打断休眠
+ //gpio_pin_clr(LORA_NRST);//lora休眠
+ //spi_close(SPI_ID0);
+ lora_in_sleep();
+ power_init();
+ mcu_deep_sleep();
+}
+}
+
+void app_restore_from_power_down(void)
+{
}
--
Gitblit v1.9.3