From ac55307242da6846c2b8fe4b710fb90feaa30978 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期三, 11 十二月 2024 17:15:39 +0800
Subject: [PATCH] PCA的INT脚加速度计清0判断成功，INT脚中断正常
---
keil/include/main/main.c | 55 ++++++++++++++++++++++++++++++++++++++++---------------
1 files changed, 40 insertions(+), 15 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 5559cc6..ceb56f5 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -61,8 +61,9 @@
#include "HIDO_ATLite.h"
#include "HIDO_Timer.h"
#include "TCPClient.h"
+#include "PCA9555.h"
-//#define DEBUG_MODE
+#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
#define TEST_UART_POLL_MODE 0
@@ -98,6 +99,11 @@
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1; //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
+extern uint8_t pca9555writedata_config[10];//暂存寄存器所有配置的数组
+extern uint8_t pca9555writedata_output[10];//暂存输出高低电平配置的数组
+extern uint8_t pca9555writedata_input[10];//暂存输入寄存器所有配置的数组
+extern uint8_t pca9555writedata_polarity[10];//暂存输入极性反转寄存器所有配置的数组
+uint8_t temp_pca9555writedata_input[10];//暂存上一次输入寄存器所有配置的数组
typedef enum
{ UN_BIND=0,
LINK_SUCCESS,
@@ -208,6 +214,7 @@
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
uint32_t keystarttime,keystarttime2;
+extern uint32_t get_in_num,get_out_num;
void MotorPoll(void)
{
if(UWB_work_state==UN_BIND) {
@@ -321,6 +328,9 @@
second_count = 0;
MinuteTask();
}
+ TagListUpdate_person_num_car();
+ in_table_log();
+
// if(!power_low_flag)
// Gps_change();
// else{
@@ -362,15 +372,24 @@
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
+void check_input_change(void)
+{
+ uint16_t gpio_state;
+ gpio_state=(uint16_t)pca9555writedata_input[0]<<8|pca9555writedata_input[1];
+ if(WAKE_UP_POSITION&gpio_state)
+ {
+ nomove_count=0;
+ }
+}
static void sleep_timer_callback(void *dev, uint32_t time)
{
- IO_control_init();
+ //IO_control_init();
if(enbale_blink_flag)
{
green_charge_state=0;
charge_red_on();
}
- UWBPoll();
+
charge_state_change();//充电状态判断
if(secondtask_count++%2==0)
{
@@ -380,7 +399,7 @@
}
if(enbale_blink_flag)
{
- delay_us(5000);
+ //delay_us(5000);
green_charge_state=0;
charge_red_off();
}
@@ -396,6 +415,11 @@
static void move_handler(enum IO_PIN_T pin)
{
nomove_count=0;
+}
+static void pca_handler(enum IO_PIN_T pin)
+{
+ PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
+ check_input_change();
}
uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
@@ -527,7 +551,7 @@
board_clock_run();
boot_deinit();
board_pins_config();
- board_debug_console_open(TRACE_PORT_UART1);
+ board_debug_console_open(TRACE_PORT_UART1);
// Reset reason
reset_cause_get();
reset_cause_clear();
@@ -570,17 +594,17 @@
IIC2_Init();
Accelerometer_Init();
- IO_control_init();
- io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
- gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
- io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
+ PCA9555_init();
+ //IO_control_init();
+// io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
+// gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
+// io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
//gps_air780_power_change(0,1);//开启gps，4G
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
gpio_pin_clr(ADC_GND_ENABLE);
Program_Init();
//uart_open(UART_ID1, &test_uart_cfg);
-
// uart1_change_from_gps_to_debug();
//Uart1GpsRecDebugSend();
uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
@@ -589,16 +613,17 @@
power_init();
//AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
- sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
+ sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
+ //sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
// board_5V_input_init(voltage_input_handler);
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
board_acceleration_detection_init(move_handler);
-// LOG_INFO(TRACE_MODULE_APP, "测试进入app");
- board_4GUsart_detection_init(_4gUsart_handler);
+ pca_input_detection_init(pca_handler);//pca检测输入
+ // LOG_INFO(TRACE_MODULE_APP, "测试进入app");
+ //board_4GUsart_detection_init(_4gUsart_handler);
while (1)
{ test4=gpio_pin_get_val(SCL_PIN);
-
+ //UWBPoll();
// if(!power_low_flag)//确认是否休眠下才开启功能
// {
// if(flag_TCP_reconnectting||IfTCPConnected())
--
Gitblit v1.9.3