From c653225a505eb47752ac707dc47f1b15385c81d8 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期五, 17 一月 2025 18:05:14 +0800
Subject: [PATCH] 加入标签电量的存储逻辑，和更新的逻辑，精简了代码函数封装
---
keil/include/main/main.c | 453 ++++++++++++++++++++++++-------------------------------
1 files changed, 199 insertions(+), 254 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 563373b..d25232f 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -61,10 +61,13 @@
#include "HIDO_ATLite.h"
#include "HIDO_Timer.h"
#include "TCPClient.h"
+#include "PCA9555.h"
+#include "WS2812.h"
#define DEBUG_MODE
extern int simple_main(void);
extern int temp_main(void);
+void uart_change_check(uint16_t gpio_state);
#define TEST_UART_POLL_MODE 0
#define TEST_UART_INTERUPT_MODE 1
#define TEST_UART_DMA_MODE 2
@@ -98,6 +101,11 @@
uint8_t recev_error_num,send_messgae_count,send_flag,control_state,power_low_flag;
uint8_t flag_4g_usart_rx_state = 1; //4G 串口RX当前是 RX状态，不是GPIO状态
int input_5v_flag,air780e_flag1,air780e_flag2,air780e_flag3,air780e_flag4;
+extern uint8_t pca9555writedata_config[10];//暂存寄存器所有配置的数组
+extern uint8_t pca9555writedata_output[10];//暂存输出高低电平配置的数组
+extern uint8_t pca9555writedata_input[10];//暂存输入寄存器所有配置的数组
+extern uint8_t pca9555writedata_polarity[10];//暂存输入极性反转寄存器所有配置的数组
+uint8_t temp_pca9555writedata_input[10];//暂存上一次输入寄存器所有配置的数组
typedef enum
{ UN_BIND=0,
LINK_SUCCESS,
@@ -128,7 +136,7 @@
.flow = UART_FLOW_CONTROL_NONE,
.rx_level = UART_RXFIFO_CHAR_1,
.tx_level = UART_TXFIFO_EMPTY,
- .baud = BAUD_115200,
+ .baud = BAUD_9600,
#if (TEST_UART_MODE == TEST_UART_POLL_MODE)
.dma_en = false,
.int_rx = false,
@@ -185,135 +193,106 @@
}
if(fVoltage_mv<3300)
{
- power_low_flag=1;
- gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G
+ //power_low_flag=1;
+ //gps_air780_power_change(gps_power_state,0);//gps原样，关闭4G
LOG_INFO(TRACE_MODULE_APP, "电池电压低于3.3V，4G，GPS停止工作\r\n");
}else{
- power_low_flag=0;
- gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
+ //power_low_flag=0;
+ //gps_air780_power_change(gps_power_state,1);//gps原样,开启4G
LOG_INFO(TRACE_MODULE_APP, "电池电压正常,4G，GPS,正常工作\r\n");
}
- gpio_pin_set(ADC_GND_ENABLE);//在拉高
+ PCA9555_Set_One_Value_Output(ADC_MINIUS,1);//拉高
// LOG_INFO(TRACE_MODULE_APP, "The voltage is %%%d \r\n",bat_percent);
}
-//void UartInit(void)
-//{
-//board_pins_config();
-//uart_open(UART_ID1, &test_uart_cfg);
-//board_debug_console_open(TRACE_PORT_UART0);
-//uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-//}
extern uint8_t gps_uwb_flag,gps_need_data_flag;
uint8_t TCP_reconnect_timer,flag_TCP_reconnectting = 1,flag_alam_state = 0,userkey_state;
uint8_t gps_enable_flag,motor_open_air_flag,moter_open_uwb_flag,flag_fenli_alarm = 0,fenli_alarm_count,delaysleep_count,enbale_blink_flag;
int need_open_gps_count;
-uint32_t keystarttime,keystarttime2;
+uint32_t keystarttime,keystarttime2,keystarttime3;
extern uint32_t get_in_num,get_out_num;
-void MotorPoll(void)
-{
- if(UWB_work_state==UN_BIND) {
- gps_uwb_flag=0;//关闭GPS
- moter_open_uwb_flag=0;//关闭震动
- need_open_gps_count=0;//清0计数gps
- } else { //绑定状态下
- if(anchordata_num==1) {
- if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
- fenli_alarm_count = 0;
- if(flag_fenli_alarm)
- {
- flag_fenli_alarm = 0;
- fenli_alarm_count = 0;
- _4GAlarmUpload(2);
- }
- }
- }
- if(distance>g_com_map[ALARM_DISTANCE1]||anchordata_num==0)
- {
- if(fenli_alarm_count++>20)
- {
- if(!flag_fenli_alarm)
- {
- flag_fenli_alarm = 1;
- _4GAlarmUpload(1);
- }
- }
- }
- if(distance<g_com_map[ALARM_DISTANCE1]) { //小于预警距离
- if(flag_alam_state)
- {
- flag_alam_state = 0;
+uint8_t flag_4G_recdata;
- }
-
- need_open_gps_count=0;
- moter_open_uwb_flag=0;//关闭震动
- gps_uwb_flag=0;//关闭GPS
- } else if(g_com_map[ALARM_DISTANCE1]<=distance&&distance<=g_com_map[ALARM_DISTANCE2]) { //大于预警距离小于报警距离
- need_open_gps_count++;
- moter_open_uwb_flag=1;//开启震动
- if(need_open_gps_count>=20) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- gps_uwb_flag=1;//开启gps测距流程
- need_open_gps_count=0;
- }
- } else if(distance>=g_com_map[ALARM_DISTANCE2]) { //大于报警距离
- need_open_gps_count++;
- moter_open_uwb_flag=1;//开启震动
- if(need_open_gps_count>=20) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- gps_uwb_flag=1;//开启gps测距流程
- need_open_gps_count=0;
- }
-
- }
- if(anchordata_num==0) {
- if(!flag_alam_state)
- {
- flag_alam_state = 1;
- }
- distance = 0x1ffff;
- gps_uwb_flag=1;//开启gps测距流程
- moter_open_uwb_flag=1;//开启震动
- need_open_gps_count=0;
- }
- }
- }
void IMUTask(void)
{
if(nomove_count>g_com_map[NOMOVESLEEP_TIME]&&g_com_map[IMU_ENABLE]==1)
- {power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
+ {//power_wakeup_enable((enum POWER_WAKEUP_SOURCE_T)ACCLERATE_DETECT_Pin, POWER_WAKEUP_LEVEL_HIGH);
mcu_deep_sleep();
}
}
void UserKeyTask(void)
- {
- if(!GET_USERKEY)
+{
+if(!read_userkey_input_pca())
{
- if(HIDO_TimerGetTick() - keystarttime>3)
+ if(HIDO_TimerGetTick() - keystarttime3>2)
{
userkey_state = 1;
- keystarttime = HIDO_TimerGetTick();
- UDPClient_UploadGPS();
+ keystarttime3 = HIDO_TimerGetTick();
+ //UDPClient_UploadGPS();
}
- if(HIDO_TimerGetTick() - keystarttime2>10)
+// if(HIDO_TimerGetTick() - keystarttime2>10)
+// {
+//
+// g_com_map[CNT_RESTART] = 1;
+// }
+ }else
+ {
+ keystarttime3 = HIDO_TimerGetTick();
+ }
+}
+void PowerTask(void)
+{
+ if(read_powerkey_input_pca())
+ {
+ if(HIDO_TimerGetTick() - keystarttime>2)
{
- g_com_map[CNT_RESTART] = 1;
+ keystarttime = HIDO_TimerGetTick();
+ PCA9555_Set_One_Value_Output(PWR_ENABLE,0);//低电平关闭
+ PCA9555_Set_One_Value_Output(GPS_LED,0);//输出低电平关闭LED
}
+// if(HIDO_TimerGetTick() - keystarttime2>10)
+// {
+//
+// g_com_map[CNT_RESTART] = 1;
+// }
}else
{
keystarttime = HIDO_TimerGetTick();
keystarttime2 = HIDO_TimerGetTick();
}
- }
+}
void MinuteTask(void)
-{ gpio_pin_clr(ADC_GND_ENABLE);//拉低
+{
+ PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
+}
+void Air780eTask(void)
+{
+// if(!power_low_flag)//确认是否休眠下才开启功能
+// {
+ if(flag_TCP_reconnectting||IfTCPConnected())
+ {
+// // LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
+//
+//// if(flag_4guart_needinit)
+//// {
+//// flag_4guart_needinit = 0;
+//// AIR780EUartInit();
+//// }//yuan
+ if(flag_4G_recdata==1)
+ {
+ flag_4G_recdata = 2;
+
+ //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
+ Socket_RecvAll();
+ }
+ Internet_Poll();
+ HIDO_ATLitePoll();
+ HIDO_TimerPoll();
+ TCPClient_Poll();
+
+ }
+// }
+
}
void SecondTask(void)
{static uint8_t second_count;
@@ -322,39 +301,26 @@
second_count = 0;
MinuteTask();
}
- TagListUpdate_person_num_car();
- in_table_log();
-
-// if(!power_low_flag)
-// Gps_change();
-// else{
-// gps_power_state=0;//关闭GPS
-// update_led_power_state();
-// //初始化GPS计数数据
-// gps_need_data_flag=1;
-// gps_wait_count2=0;
-// gps_wait_count=0;
-// }
// //UWB状态检测
//if(!power_low_flag)//低供电下不需要检测重连
// {
-// if(IfTCPConnected())
-// {
-// TCP_reconnect_timer =0;
-// flag_TCP_reconnectting = 0;
-// } else {
-// if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
-// {
-// flag_TCP_reconnectting = 1;
-// } else {
-// flag_TCP_reconnectting = 0;
-// }
-// if(TCP_reconnect_timer++>600)
-// {
-// TCP_reconnect_timer = 0;
-// }
+ if(IfTCPConnected())
+ {
+ TCP_reconnect_timer =0;
+ flag_TCP_reconnectting = 0;
+ } else {
+ if(TCP_reconnect_timer<30)//如果TCP没有连接，每隔10分钟尝试连接30秒
+ {
+ flag_TCP_reconnectting = 1;
+ } else {
+ flag_TCP_reconnectting = 0;
+ }
+ if(TCP_reconnect_timer++>600)
+ {
+ TCP_reconnect_timer = 0;
+ }
-// }
+ }
// }
HIDO_TimerTick();
if(nomove_count<=g_com_map[NOMOVESLEEP_TIME])//防止溢出
@@ -366,42 +332,45 @@
uint8_t tt=1;
uint8_t flag_sleeptimer,flag_secondtask,secondtask_count,log_4g_enable_flag;
uint8_t uwb_enable_flag=0;
+
+void check_input_change(void)
+{
+ uint16_t gpio_state;
+ gpio_state=(uint16_t)pca9555writedata_input[0]<<8|pca9555writedata_input[1];
+ if(WAKE_UP_POSITION&gpio_state)
+ {
+ nomove_count=0;
+ }
+ if(!(MAIN_RI_POSITION&gpio_state))
+ {
+ flag_4G_recdata = 1;
+ delaysleep_count = 3;
+ }
+ //uart_change_check(gpio_state);
+}
static void sleep_timer_callback(void *dev, uint32_t time)
{
- IO_control_init();
- if(enbale_blink_flag)
- {
- green_charge_state=0;
- charge_red_on();
- }
-
- charge_state_change();//充电状态判断
if(secondtask_count++%2==0)
{
flag_secondtask = 1;
}else{
flag_secondtask = 0;
}
- if(enbale_blink_flag)
- {
- delay_us(5000);
- green_charge_state=0;
- charge_red_off();
- }
if(delaysleep_count>0)
delaysleep_count--;
//GPS工作逻辑
}
-static void voltage_input_handler(enum IO_PIN_T pin)
+//static void move_handler(enum IO_PIN_T pin)
+//{
+// nomove_count=0;
+//}
+static void pca_handler(enum IO_PIN_T pin)
{
+ PCA9555_readdata(PCA9555_DEVICE_ADDR,pca9555writedata_input);//读输入寄存器的值
+ check_input_change();
+}
-}
-static void move_handler(enum IO_PIN_T pin)
-{
- nomove_count=0;
-}
-uint8_t flag_4G_recdata;
void _4gUsart_handler(enum IO_PIN_T pin)
{
//LOG_INFO(TRACE_MODULE_APP, "4G RX 唤醒\r\n");
@@ -455,57 +424,54 @@
}
-
+void uart_change_check(uint16_t gpio_state)
+{
+ if(INPUT_5V_POSITION&gpio_state)
+ {
+ if(state5v==0)
+ {
+ state5v=1;
+ state5V_prase_flag=state5v;
+ gps_prase_flag=0;//解除gps解析
+ uart1_change_from_gps_to_debug();//测试
+ PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
+ }
+ }else {
+ if(state5v==1)
+ {
+ g_com_map[MODBUS_MODE] = 0;
+ state5v=0;
+ state5V_prase_flag=state5v;
+ gps_prase_flag=1;//恢复gps解析
+ uart1_change_from_debug_to_gps();//测试
+ PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
+ }
+ }
+}
void IdleTask(void)
{
-// if(gpio_pin_get_val(INPUT_5V_Pin))
-// {
-
-// if(state5v==0)
-// {
-// state5v=1;
-// state5V_prase_flag=state5v;
-// gps_prase_flag=0;//解除gps解析
-// uart1_change_from_gps_to_debug();//测试
-// // uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
-// //UartInit();
-// }
-
-// //UART_CheckSend();
-// } else {
-// if(state5v==1)
-// {
-// g_com_map[MODBUS_MODE] = 0;
-// state5v=0;
-// state5V_prase_flag=state5v;
-// gps_prase_flag=1;//恢复gps解析
-// uart1_change_from_debug_to_gps();//测试
-// // uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);//开启dma
-// //UartDeinit();
-// }
-// }
+if(read_5v_input_pca())
+ {
+ if(state5v==0)
+ {
+ state5v=1;
+ state5V_prase_flag=state5v;
+ gps_prase_flag=0;//解除gps解析
+ uart1_change_from_gps_to_debug();//测试
+ PCA9555_Set_One_Value_Output(MCU_A,1);//输出高电平切换为5V输入
+ }
+ }else {
+ if(state5v==1)
+ {
+ g_com_map[MODBUS_MODE] = 0;
+ state5v=0;
+ state5V_prase_flag=state5v;
+ gps_prase_flag=1;//恢复gps解析
+ uart1_change_from_debug_to_gps();//测试
+ PCA9555_Set_One_Value_Output(MCU_A,0);//输出低电平切换为GPS
+ }
+ }
UART_CheckReceive();
-}
-int bind_check(void)
-{
- if(g_com_map[BIND_DEV_ID]!=0x00)
- {
- return 1;
-//绑定信息为1说明设备已经被下发绑定
- } else {
- return 0;
-//绑定信息为0说明设备未被绑定
- }
-}
-void check_if_in_search(void)
-{
- if(link_success_flag==1) { //如果第一次测距收包成功那么则进入连接测距模式
- UWB_work_state=LINK_SUCCESS;
- } else { //否则进入搜索模式
- UWB_work_state=SEARCH_DEV;
- if(first_search_flag==0)
- first_search_flag=1;
- }
}
void boot_deinit(void)
{
@@ -531,11 +497,11 @@
board_clock_run();
boot_deinit();
board_pins_config();
- board_debug_console_open(TRACE_PORT_UART1);
+ board_debug_console_open_baud(TRACE_PORT_UART1,BAUD_115200);
// Reset reason
reset_cause_get();
reset_cause_clear();
-
+//注意串口一波特率改为9600了为了能和GPS通信上
// Load calibration parameters from NVM
uint32_t internal_flash = (REG_READ(0x40000018) >> 17) & 0x1;
uint32_t external_flash = (REG_READ(0x40010030) >> 28) & 0x3;
@@ -559,84 +525,63 @@
// open system timer
//sys_timer_open();
-
- // TODO 4G
+ // TODO 4G
Uart_Register(UART_ID_4G, UART_ID0);
-// Internet_Init();
-// TCPClient_Init();
-
+ Internet_Init();
+ TCPClient_Init();
gpio_open();
- board_output_init();//配置adcGND引脚
-// battery_monitor_open();
-// Voltage_input=battery_monitor_get();
-// battery_monitor_close();
+ LED_output_init();//配置彩色灯引脚
+ IIC2_Init();
+ Accelerometer_Init();
+ PCA9555_init();
+
+
+ //AIR780E_Reset();
+
adc_open(&usr_adc_cfg);
- IIC2_Init();
- Accelerometer_Init();
- IO_control_init();
- io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
- gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
- io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
- //gps_air780_power_change(0,1);//开启gps，4G
-//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
- gpio_pin_clr(ADC_GND_ENABLE);
-
+ if(!read_5v_input_pca())
+ {
+ Set4LEDColor(BLUE,GREEN,WHITE,GREEN);
+ delay_ms(500);
+ Set4LEDColor(RED,WHITE,RED,WHITE);
+ delay_ms(500);
+ //Set4LEDColor(LEDOFF,LEDOFF,LEDOFF,LEDOFF);
+ }
+// io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
+// gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
+// io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
Program_Init();
//uart_open(UART_ID1, &test_uart_cfg);
-
// uart1_change_from_gps_to_debug();
//Uart1GpsRecDebugSend();
uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
-// Initialize low power mode
+ // Initialize low power mode
power_init();
//AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
+ //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
- // board_5V_input_init(voltage_input_handler);
+ PCA9555_Set_One_Value_Output(ADC_MINIUS,0);//拉低
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
- board_acceleration_detection_init(move_handler);
-// LOG_INFO(TRACE_MODULE_APP, "测试进入app");
- board_4GUsart_detection_init(_4gUsart_handler);
+ //board_acceleration_detection_init(move_handler);
+ pca_input_detection_init(pca_handler);//pca检测输入
+ //board_4GUsart_detection_init(_4gUsart_handler);
+ Uwb_init();
+ OpenUWB();
while (1)
- { test4=gpio_pin_get_val(SCL_PIN);
- UWBPoll();
-// if(!power_low_flag)//确认是否休眠下才开启功能
-// {
-// if(flag_TCP_reconnectting||IfTCPConnected())
-// {
-// // LOG_INFO(TRACE_MODULE_APP, "处理4G任务\r\n");
-//
-//// if(flag_4guart_needinit)
-//// {
-//// flag_4guart_needinit = 0;
-//// AIR780EUartInit();
-//// }//yuan
-// if(flag_4G_recdata==1)
-// {
-// flag_4G_recdata = 2;
-//
-// //LOG_INFO(TRACE_MODULE_APP, "运行Socket_RecvAll tt2 %d\r\n",tt2);
-// Socket_RecvAll();
-// }
-//// air780_led_on();
-// Internet_Poll();
-// HIDO_ATLitePoll();
-// HIDO_TimerPoll();
-// TCPClient_Poll();
-//// air780_led_off();
-// }
-// }
+ {
+ uwb_app_poll();
+ Air780eTask();
if(flag_secondtask)
{
flag_secondtask = 0;
SecondTask();
-
}
-// UserKeyTask();
+ PowerTask();
// IMUTask();
+ UserKeyTask();
IdleTask();
#ifndef DEBUG_MODE
//if(flag_sleeptimer)
--
Gitblit v1.9.3