From c8c1cf5223f0576d4c378ac627d6eeed6caf04d5 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期三, 07 五月 2025 15:38:06 +0800
Subject: [PATCH] 成功加入log打印和校准逻辑
---
keil/include/main/main.c | 33 ++++++++++++++++++++++-----------
1 files changed, 22 insertions(+), 11 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 521a520..689e4c9 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -145,7 +145,7 @@
};
void uart_receive_callback(void *dev, uint32_t err_code)
{
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
}
void mcu_deep_sleep(void)
{
@@ -322,8 +322,9 @@
second_count = 0;
MinuteTask();
}
- TagListUpdate_person_num();
- LOG_INFO(TRACE_MODULE_APP,"车内：%d 人,车外: %d 人\r\n",get_in_num,get_out_num);
+ TagListUpdate_person_num_car();
+ //in_table_log();
+
// if(!power_low_flag)
// Gps_change();
// else{
@@ -383,7 +384,7 @@
}
if(enbale_blink_flag)
{
- delay_us(5000);
+ //delay_us(5000);
green_charge_state=0;
charge_red_off();
}
@@ -410,6 +411,7 @@
extern uint16_t ip0,ip1,ip2,ip3,port;
extern uint8_t gps_4g_flag;
extern uint8_t gps_need_data_flag,gps_open_flag;
+extern float pd_offset,offset;
void Program_Init(void)
{
Usart1ParseDataCallback = UsartParseDataHandler;//需改为默认为gps处理，UsartParseDataHandler为升级处理当调试时候改为
@@ -418,6 +420,7 @@
group_id=g_com_map[GROUP_ID];//组ID
// tag_frequency = 1000/g_com_map[COM_INTERVAL];//测距频率这个存的是测距时间
memcpy(&disoffset,&g_com_map[DIST_OFFSET],2);
+ memcpy(&pd_offset,&g_com_map[PDOFFSET],4);
// g_com_map[ALARM_DISTANCE1] = 40;
// g_com_map[ALARM_DISTANCE2] = 40;
warning_distance=g_com_map[ALARM_DISTANCE1];
@@ -454,7 +457,7 @@
}
-
+uint8_t calibration_start;
void IdleTask(void)
{
// if(gpio_pin_get_val(INPUT_5V_Pin))
@@ -483,7 +486,13 @@
// //UartDeinit();
// }
// }
- UART_CheckReceive();
+ UART0_CheckReceive();
+ if(g_com_map[CNT_CALIB])
+ {
+ g_com_map[CNT_CALIB]=0;
+ save_com_map_to_flash();
+ calibration_start=1;
+ }
}
int bind_check(void)
{
@@ -530,7 +539,7 @@
board_clock_run();
boot_deinit();
board_pins_config();
- board_debug_console_open(TRACE_PORT_UART1);
+ board_debug_console_open(TRACE_PORT_UART0);
// Reset reason
reset_cause_get();
reset_cause_clear();
@@ -565,6 +574,8 @@
// TCPClient_Init();
gpio_open();
+
+
board_output_init();//配置adcGND引脚
// battery_monitor_open();
// Voltage_input=battery_monitor_get();
@@ -575,7 +586,7 @@
Accelerometer_Init();
IO_control_init();
io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
- gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
+ gpio_pin_set_dir(SCL_PIN , GPIO_DIR_OUT, 0);
io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
//gps_air780_power_change(0,1);//开启gps，4G
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
@@ -586,13 +597,13 @@
// uart1_change_from_gps_to_debug();
//Uart1GpsRecDebugSend();
- uart_receive(UART_ID1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
+ uart_receive(UART_ID0,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE,uart_receive_callback);
// Initialize low power mode
power_init();
//AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
+ //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
// board_5V_input_init(voltage_input_handler);
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
@@ -600,7 +611,7 @@
// LOG_INFO(TRACE_MODULE_APP, "测试进入app");
board_4GUsart_detection_init(_4gUsart_handler);
while (1)
- { test4=gpio_pin_get_val(SCL_PIN);
+ {
UWBPoll();
// if(!power_low_flag)//确认是否休眠下才开启功能
// {
--
Gitblit v1.9.3