From d9eeaa73e91eb757f8707e26f204f443fe956a3f Mon Sep 17 00:00:00 2001
From: zhangbo <zhangbo@qq.com>
Date: 星期二, 04 三月 2025 15:16:26 +0800
Subject: [PATCH] lora能正常发送
---
keil/sn74hc595.c | 87 +++++++++++++++++++++++++++----------------
1 files changed, 54 insertions(+), 33 deletions(-)
diff --git a/keil/sn74hc595.c b/keil/sn74hc595.c
index 7847d5f..5cc0ab7 100644
--- a/keil/sn74hc595.c
+++ b/keil/sn74hc595.c
@@ -1,21 +1,21 @@
#include "sn74hc595.h"
-void IO_control_init(void)
-{
-//SDA->SER
- io_open_drain_set(SER_PIN, 0);
- io_pin_mux_set(SER_PIN,IO_FUNC0);//把原先io SDA变为普通GPIO
- gpio_pin_set_dir(SER_PIN , GPIO_DIR_OUT, 0);//复用原先GPIO引脚为SER
- io_pull_set(SER_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
-//SRCLK
- io_pin_mux_set(SRCLK_PIN,IO_FUNC0);
- gpio_pin_set_dir(SRCLK_PIN , GPIO_DIR_OUT, 0);
- io_pull_set(SRCLK_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
-//RCLK
- io_pin_mux_set(RCLK_PIN,IO_FUNC0);
- gpio_pin_set_dir(RCLK_PIN , GPIO_DIR_OUT, 0);
- io_pull_set(RCLK_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
-}
+//void IO_control_init(void)
+//{
+////SDA->SER
+// io_open_drain_set(SER_PIN, 0);
+// io_pin_mux_set(SER_PIN,IO_FUNC0);//把原先io SDA变为普通GPIO
+// gpio_pin_set_dir(SER_PIN , GPIO_DIR_OUT, 0);//复用原先GPIO引脚为SER
+// io_pull_set(SER_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
+////SRCLK
+// io_pin_mux_set(SRCLK_PIN,IO_FUNC0);
+// gpio_pin_set_dir(SRCLK_PIN , GPIO_DIR_OUT, 0);
+// io_pull_set(SRCLK_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
+////RCLK
+// io_pin_mux_set(RCLK_PIN,IO_FUNC0);
+// gpio_pin_set_dir(RCLK_PIN , GPIO_DIR_OUT, 0);
+// io_pull_set(RCLK_PIN , IO_PULL_DOWN, IO_PULL_UP_LEVEL4);
+//}
void IO_LED_control_change(uint8_t data)
{
@@ -25,12 +25,12 @@
SER_1;
else
SER_0;
- SRCLK_1;//将数据放入移位寄存器
- SRCLK_0;
+// SRCLK_1;//将数据放入移位寄存器
+// SRCLK_0;
data>>=1;
}
- RCLK_1;//将数据存入存储器并输出
- RCLK_0;
+// RCLK_1;//将数据存入存储器并输出
+// RCLK_0;
}
//高电平开启power，低电平关闭power
void gps_air780_power_change(uint8_t gps_state,uint8_t air_state)
@@ -45,19 +45,30 @@
IO_LED_control_change(control_state);
}
void blink_led(uint8_t*state)
-{if(*state==0)
- *state=1;
- else{
- *state=0;
- }
-update_led_power_state();
-delay_us(100);
-if(*state==0)
- *state=1;
- else{
- *state=0;
- }
-update_led_power_state();
+{ if(*state==0)
+ *state=1;
+ else {
+ *state=0;
+ }
+ update_led_power_state();
+ delay_us(1000);
+ if(*state==0)
+ *state=1;
+ else {
+ *state=0;
+ }
+ update_led_power_state();
+}
+
+void gps_led_on(void)
+{
+ gps_success_state=1;//uwb亮起
+ update_led_power_state();
+}
+void gps_led_off(void)
+{
+ gps_success_state=0;//uwb灭
+ update_led_power_state();
}
void uwb_led_on(void)
{
@@ -68,4 +79,14 @@
{
uwb_state=0;//uwb灭
update_led_power_state();
+}
+void air780_led_on(void)
+{
+ air780_success_state=1;//uwb亮起
+ update_led_power_state();
+}
+void air780_led_off(void)
+{
+ air780_success_state=0;//uwb灭
+ update_led_power_state();
}
\ No newline at end of file
--
Gitblit v1.9.3