From fef76b2f74d65ae80a890bbc8ce2be8e591cdd03 Mon Sep 17 00:00:00 2001
From: chen <15335560115@163.com>
Date: 星期二, 06 五月 2025 15:38:04 +0800
Subject: [PATCH] 修改为AOA跟随模块测试基站，成功输出角度和距离一直测距版本
---
keil/include/main/main.c | 14 ++++++++------
1 files changed, 8 insertions(+), 6 deletions(-)
diff --git a/keil/include/main/main.c b/keil/include/main/main.c
index 563373b..ad0570f 100644
--- a/keil/include/main/main.c
+++ b/keil/include/main/main.c
@@ -323,7 +323,7 @@
MinuteTask();
}
TagListUpdate_person_num_car();
- in_table_log();
+ //in_table_log();
// if(!power_low_flag)
// Gps_change();
@@ -384,7 +384,7 @@
}
if(enbale_blink_flag)
{
- delay_us(5000);
+ //delay_us(5000);
green_charge_state=0;
charge_red_off();
}
@@ -531,7 +531,7 @@
board_clock_run();
boot_deinit();
board_pins_config();
- board_debug_console_open(TRACE_PORT_UART1);
+ board_debug_console_open(TRACE_PORT_UART0);
// Reset reason
reset_cause_get();
reset_cause_clear();
@@ -566,6 +566,8 @@
// TCPClient_Init();
gpio_open();
+
+
board_output_init();//配置adcGND引脚
// battery_monitor_open();
// Voltage_input=battery_monitor_get();
@@ -576,7 +578,7 @@
Accelerometer_Init();
IO_control_init();
io_pin_mux_set(SCL_PIN, IO_FUNC0);//测试测距波形
- gpio_pin_set_dir(SCL_PIN , GPIO_DIR_IN, 0);
+ gpio_pin_set_dir(SCL_PIN , GPIO_DIR_OUT, 0);
io_pull_set(SCL_PIN , IO_PULL_UP, IO_PULL_UP_LEVEL4);
//gps_air780_power_change(0,1);//开启gps，4G
//加速度计初始化必须在IO_control_init之前因为复用SDA引脚
@@ -593,7 +595,7 @@
power_init();
//AIR780E_Reset(); //4G模块重启，耗时1.5秒,这个是无法同步的关键
sleep_timer_open(true, SLEEP_TIMER_MODE_RELOAD, sleep_timer_callback);
- sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
+ //sleep_timer_start(__MS_TO_32K_CNT(g_com_map[COM_INTERVAL]));//测试
sleep_timer_start(__MS_TO_32K_CNT(SLEEP_TIMER_NUM));//测试
// board_5V_input_init(voltage_input_handler);
adc_get(&sample[0], NUM_SAMPLES, adc_callback);//adc采样
@@ -601,7 +603,7 @@
// LOG_INFO(TRACE_MODULE_APP, "测试进入app");
board_4GUsart_detection_init(_4gUsart_handler);
while (1)
- { test4=gpio_pin_get_val(SCL_PIN);
+ {
UWBPoll();
// if(!power_low_flag)//确认是否休眠下才开启功能
// {
--
Gitblit v1.9.3