From 170e557c0d38e66e6100d32a2a465ee1cd6f5275 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期三, 07 十月 2020 18:17:34 +0800
Subject: [PATCH] 配临近初步测试完成
---
源码/核心板/Src/application/dw_app.c | 269 ++++++++++++++++++++++++++++++++++++++++-------------
1 files changed, 202 insertions(+), 67 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index 9218bde..cb75c4a 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -120,7 +120,9 @@
* For initialisation, DW1000 clocks must be temporarily set to crystal speed. After initialisation SPI rate can be increased for optimum
* performance. */
Reset_DW1000();//重启DW1000 /* Target specific drive of RSTn line into DW1000 low for a period. */
+ status_reg = dwt_read32bitreg(SYS_STATUS_ID);
dwt_initialise(DWT_LOADUCODE);//初始化DW1000
+ status_reg = dwt_read32bitreg(SYS_STATUS_ID);
Spi_ChangePrescaler(SPIx_PRESCALER_FAST); //设置为快速模式
/* Configure DW1000. See NOTE 6 below. */
@@ -171,6 +173,7 @@
dwt_configuresleep(0x940, 0x7);
dwt_entersleep();
}
+
extern uint8_t g_start_send_flag;
u8 g_start_sync_flag;
void SyncPoll(u8 sync_seq,uint32_t sync_baseid)
@@ -311,6 +314,162 @@
u8 exsistbase_list[MAX_NEARBASE_NUM],report_num,get_newbase=0;
u16 temp_sync_timer1,temp_sync_timer2;
+void Poll(void)
+{
+ uint32_t frame_len;
+ uint32_t final_tx_time;
+ u32 start_poll;
+ int32_t mindist=999999,minid=-1,temp_dist;
+ u8 i,getsync_flag=0;
+ dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+ tag_succ_times = 0;
+ GPIO_WriteBit(GPIOA, GPIO_Pin_9, Bit_RESET);
+ for(i=0;i<g_com_map[MAX_REPORT_ANC_NUM];i++)
+ {
+ /* Write frame data to DW1000 and prepare transmission. See NOTE 7 below. */
+ tx_poll_msg[ANC_TYPE_IDX] = i;
+ dwt_writetxdata(sizeof(tx_poll_msg), tx_poll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(sizeof(tx_poll_msg), 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+ start_poll = time32_incr;
+ /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
+ { if(time32_incr - start_poll>20)
+ NVIC_SystemReset();
+ };
+ if(status_reg==0xffffffff)
+ {
+ NVIC_SystemReset();
+ }
+ if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
+ {
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+ frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
+ dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ {
+ poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
+ resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
+ if(getsync_flag==0)
+ {
+ getsync_flag=1;
+ memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
+ memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
+ memcpy(&tagslotpos,&rx_buffer[TAGSLOTPOS],2);
+ tmp_time=tmp_time+450;
+ if(tmp_time>999)
+ {
+ tmp_time-=999;
+ sync_timer++;
+ if(sync_timer>=1010)
+ {sync_timer=0;}
+ }
+ TIM3->CNT=tmp_time;
+ if(tagslotpos>max_slotpos)
+ tagslotpos=tagslotpos%(max_slotpos+1);
+ tyncpoll_time=(tagslotpos-1)*slottime;
+ }
+
+ memcpy(&temp_dist, &rx_buffer[DIST_IDX], 4);
+ memcpy(&tx_final_msg[ANCHOR_ID_IDX], &rx_buffer[ANCHOR_ID_IDX], 4);
+ /* Compute final message transmission time. See NOTE 9 below. */
+ final_tx_time = (resp_rx_ts + (RESP_RX_TO_FINAL_TX_DLY_UUS * UUS_TO_DWT_TIME)) >> 8;//计算final包发送时间，T5=T4+Treply2
+ dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+ final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
+ final_msg_set_ts(&tx_final_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
+ final_msg_set_ts(&tx_final_msg[FINAL_MSG_RESP_RX_TS_IDX], resp_rx_ts);
+ final_msg_set_ts(&tx_final_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
+ dwt_writetxdata(sizeof(tx_final_msg), tx_final_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(sizeof(tx_final_msg), 0);//设定发送数据长度
+ result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ tag_succ_times++;
+ LED0_BLINK;
+
+ if(temp_dist<mindist)
+ {
+ memcpy(&minid, &rx_buffer[ANCHOR_ID_IDX], 4);
+ tag_state=GETNEARMSG;
+ trygetnearmsg_times=5;
+ mindist=temp_dist;
+ }
+ if(result==0)
+ {while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
+ { };
+ }
+ /* Clear TXFRS event. */
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_TXFRS);//清除标志位
+ random_delay_tim = 0;
+ }
+ else
+ {
+ random_delay_tim = DFT_RAND_DLY_TIM_MS; //如果通讯失败，将间隔时间增加5ms，避开因为多标签同时发送引起的冲突。
+ }
+ }
+ else
+ {
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
+ random_delay_tim = DFT_RAND_DLY_TIM_MS;
+ }
+}
+ if(getsync_flag==0)
+ {
+ tagslotpos--;
+ if(tagslotpos==0||tagslotpos>max_slotpos)
+ {
+ tagslotpos=max_slotpos;
+ }
+ tyncpoll_time=(tagslotpos-1)*slottime;
+ }
+ mainbase_id=minid;
+}
+u8 nearmsg_mainbase=0,rec_tagpos_emptylist[32];
+void GetNearMsg(void)
+{
+ u32 start_poll,frame_len;
+
+ memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
+ memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
+ tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
+
+ dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+ dwt_writetxdata(12, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(12, 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE| DWT_RESPONSE_EXPECTED);
+ start_poll = time32_incr;
+ /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
+ { if(time32_incr - start_poll>20)
+ NVIC_SystemReset();
+ };
+ if(status_reg==0xffffffff)
+ {
+ NVIC_SystemReset();
+ }
+ if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
+ {
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+ frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
+ dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_MSG&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ {
+ next_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
+ tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
+ //tagslotpos=rx_buffer[TAGSLOTPOS];
+ memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],next_nearbase_num*2);
+ //slottime=ceil((nearbase_num+2)*0.4)+2;
+ tyncpoll_time=tagslotpos*slottime;
+ tag_state=NEARPOLL;
+ }else{
+ tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
+ }
+ }else{
+ tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
+ }
+
+}
void NearPoll(void)
{
static u8 mainbase_lost_count=0,flag_finalsend,flag_rxon;
@@ -365,6 +524,9 @@
dwt_forcetrxoff();
dwt_setdelayedtrxtime(final_tx_time);
result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ #ifdef DEBUG_INF
+ USART_putc(0x33);
+ #endif
break;
}
}
@@ -425,6 +587,9 @@
// tagslotpos=tagslotpos%(max_slotpos+1);
// tyncpoll_time=(tagslotpos-1)*slottime;
////////////////////////////
+ #ifdef DEBUG_INF
+ USART_putc(0x31);
+ #endif
rec_nearbasepos=0;
memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
@@ -448,6 +613,7 @@
memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
if(temp_dist!=0x1ffff)
{
+ #ifdef TAG_OUTPUT
#ifndef USART_INTEGRATE_OUTPUT
usart_send[2] = 1;//正常模式
usart_send[3] = 17;//数据段长度
@@ -467,6 +633,7 @@
memcpy(&usart_send[19],&checksum,2);
UART_PushFrame(usart_send,21);
#endif
+ #endif
//dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
@@ -483,7 +650,9 @@
nearbaseid_list[rec_nearbasepos] = rec_nearbaseid;
memcpy(&tx_nearfinal_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
}
-
+ #ifdef DEBUG_INF
+ USART_putc(0x32);
+ #endif
memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
nearbase_distlist[rec_nearbasepos]=temp_dist;
@@ -498,6 +667,7 @@
// tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
if(temp_dist!=0x1ffff)
{
+ #ifdef TAG_OUTPUT
#ifndef USART_INTEGRATE_OUTPUT
usart_send[2] = 1;//正常模式
usart_send[3] = 17;//数据段长度
@@ -517,7 +687,7 @@
memcpy(&usart_send[19],&checksum,2);
UART_PushFrame(usart_send,21);
#endif
-
+ #endif
//dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
//dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
@@ -525,6 +695,9 @@
}
}
}else{
+ #ifdef DEBUG_INF
+ printf("response包失败：%x/n",status_reg);
+ #endif
dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
if(flag_rxon)
{dwt_rxenable(0);
@@ -618,6 +791,9 @@
memcpy(&usart_send[4+report_num*6],&checksum,2);
UART_PushFrame(usart_send,6+report_num*6);
#endif
+ #ifdef DEBUG_INF
+ printf("序号：%d,基站数量：%d/n",(frame_seq_nb-1)&0xff,nearbase_num);
+ #endif
// if(mainbase_lost_count>5)
// {
// //tag_state=DISCPOLL;
@@ -636,57 +812,6 @@
dwt_forcetrxoff();
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
}
-u8 nearmsg_mainbase=0,rec_tagpos_emptylist[32];
-void GetNearMsg(void)
-{
- u32 start_poll,frame_len;
- if(nearmsg_mainbase)
- {nearmsg_mainbase=0;
- }else{
- nearmsg_mainbase=1;
- }
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&nearmsg_mainbase,2);
- memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
- tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
-
- dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
- dwt_writetxdata(12, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(12, 0);//设置超宽带发送数据长度
- dwt_starttx(DWT_START_TX_IMMEDIATE| DWT_RESPONSE_EXPECTED);
- start_poll = time32_incr;
- /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
- { if(time32_incr - start_poll>20)
- NVIC_SystemReset();
- };
- if(status_reg==0xffffffff)
- {
- NVIC_SystemReset();
- }
- if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
- {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
- frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
- dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_MSG&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
- {
- next_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
- memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
- //tagslotpos=rx_buffer[TAGSLOTPOS];
- memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],next_nearbase_num*2);
- //slottime=ceil((nearbase_num+2)*0.4)+2;
- tyncpoll_time=tagslotpos*slottime;
- tag_state=NEARPOLL;
- }else{
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- }
- }else{
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- }
-
-}
void Tag_App(void)//发送模式(TAG标签)
{
@@ -697,7 +822,7 @@
switch(tag_state)
{
case DISCPOLL:
-
+ Poll();
break;
case GETNEARMSG:
GetNearMsg();
@@ -971,6 +1096,9 @@
memcpy(&usart_send_anc[6+6*anc_report_num],&tagdist_list[taglist_pos],4);
anc_report_num++;
#endif
+ #ifdef DEBUG_INF
+ printf("序号：%d\r\n",frame_seq_nb2);
+ #endif
}else{
// printf("%d",hex_dist);
misdist_num[taglist_pos]++;
@@ -990,7 +1118,9 @@
}
}
}else{
- //printf("%x/n",status_reg);
+ #ifdef DEBUG_INF
+ printf("final包失败：%x/n",status_reg);
+ #endif
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
@@ -1029,10 +1159,10 @@
memcpy(&tag_id_recv,&rx_buffer[TAG_ID_IDX],2);
switch(rx_buffer[MESSAGE_TYPE_IDX])
{
-// case POLL:
-// if (anchor_type == rx_buffer[ANC_TYPE_IDX])
-// Anchor_RecPoll();
-// break;
+ case POLL:
+ if (anchor_type == rx_buffer[ANC_TYPE_IDX])
+ Anchor_RecPoll();
+ break;
case SYNC:
memcpy(&rec_syncid,&rx_buffer[ANCHOR_ID_IDX],4);
if(rec_syncid<current_syncid)
@@ -1059,14 +1189,15 @@
}
break;
case NEAR_MSG:
- if(anc_id_recv==flag_syncbase)
+ if(anc_id_recv==dev_id)
{
rx_buffer[TAGSLOTPOS]=taglist_pos;
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
memcpy(&tx_near_msg[TAG_ID_IDX],&tag_id_recv,2);
memcpy(&tx_near_msg[NEARMSG_EMPTYSLOTPOS_INDEX],&tagpos_binary,4);
- tx_near_msg[NEARBASENUM_INDEX]=ancidlist_num;
- memcpy(&tx_near_msg[NEARBASEID_INDEX],&ancidlist_send,ancidlist_num*2);
+ ancidlist_num=g_com_map[NEARBASE_NUM];
+ tx_near_msg[NEARBASENUM_INDEX]=g_com_map[NEARBASE_NUM];
+ memcpy(&tx_near_msg[NEARBASEID_INDEX],&g_com_map[NEARBASE_ID1],g_com_map[NEARBASE_NUM]*2);
send_len=11+ancidlist_num*2+2;
dwt_writetxdata(send_len, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
dwt_writetxfctrl(send_len, 0);//设置超宽带发送数据长度
@@ -1107,16 +1238,20 @@
break;
}
}
- if(i==rec_nearbase_num)
- {
- seize_anchor=1; //抢占anchor
- Anchor_RecNearPoll(i);
- }
+ //抢占模式
+// if(i==rec_nearbase_num)
+// {
+// seize_anchor=1; //抢占anchor
+// Anchor_RecNearPoll(i);
+// }
break;
}
}else{
+ #ifdef DEBUG_INF
+ printf("poll包失败：%x/n",status_reg);
+ #endif
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
--
Gitblit v1.9.3