From 41776246aed24b42e1d05da230f6f114e02c87b6 Mon Sep 17 00:00:00 2001
From: guanjiao <sqrgj@163.com>
Date: 星期日, 27 五月 2018 17:39:52 +0800
Subject: [PATCH] 增加低通滤波与渐进报警功能
---
源码/核心板/Src/application/dw_app.c | 39 ---------------------------------------
1 files changed, 0 insertions(+), 39 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index db01397..822a810 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -292,26 +292,6 @@
dwt_writetxdata(sizeof(tx_final_msg), tx_final_msg, 0);//将发送数据写入DW1000
dwt_writetxfctrl(sizeof(tx_final_msg), 0);//设定发送数据长度
dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
-
- //这里为串口输出
-// if (GPIO_ReadInputDataBit(GPIOA, SW2) != RESET) //通过拨码开关判断数据输出格式
-// {
-// dID = TAG_ID;
-// printf("TAG_ID: %2.0f ", dID);
-// dID = ANCHOR_ID;
-// printf("ANCHOR_ID: %2.0f ", dID);
-// printf("Distance: %5.0f cm\n", (double)dist[TAG_ID]);
-// }
-// else
-// {
-// send[2] = ANCHOR_ID;
-// send[3] = TAG_ID;
-
-// memcpy(&send[4], &dist[TAG_ID], 2);
-// check = Checksum_u16(&send[2], 6);
-// memcpy(&send[8], &check, 2);
-// USART_puts(send, 10);
-// }
/* Poll DW1000 until TX frame sent event set. See NOTE 8 below. */
while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
@@ -451,25 +431,6 @@
// dist[TAG_ID] = LP(dis, TAG_ID); //LP 为低通滤波器，让数据更稳定
LED0_BLINK; //每成功一次通讯则闪烁一次
- //这里供串口输出
-// if (GPIO_ReadInputDataBit(GPIOA, SW2) != RESET) //通过拨码开关判断数据输出格式
-// {
-// dID = TAG_ID;
-// printf("TAG_ID: %2.0f ", dID);
-// dID = ANCHOR_ID;
-// printf("ANCHOR_ID: %2.0f ", dID);
-// printf("Distance: %5.0f cm\n", (double)dist[TAG_ID]);
-// }
-// else
-// {
-// send[2] = ANCHOR_ID;
-// send[3] = TAG_ID;
-
-// memcpy(&send[4], &dist[TAG_ID], 2);
-// check = Checksum_u16(&send[2], 6);
-// memcpy(&send[8], &check, 2);
-// USART_puts(send, 10);
-// }
}
}
--
Gitblit v1.9.3