From 5bdc868b2ef673bbce5e0abbc2a7bf8f7f8fa55e Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期二, 27 四月 2021 11:59:30 +0800
Subject: [PATCH] V2.17 增加基站汇总模式，青岛待测试
---
源码/核心板/Src/application/dw_app.c | 1049 +++++++++++++++++++++++++++++++++++++++++----------------
1 files changed, 754 insertions(+), 295 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index 2647999..c9eaf86 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -1,18 +1,19 @@
#include "dw_app.h"
+#include "ADC.h"
enum enumtagstate
{
DISCPOLL,
GETNEARMSG,
NEARPOLL,
-}tag_state;
+}tag_state=GETNEARMSG;
static dwt_config_t config = {
2, /* Channel number. */
DWT_PRF_64M, /* Pulse repetition frequency. */
- DWT_PLEN_128, /* Preamble length. */
+ DWT_PLEN_64, /* Preamble length. */
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
9, /* TX preamble code. Used in TX only. */
9, /* RX preamble code. Used in RX only. */
- 0, /* Use non-standard SFD (Boolean) */
+ 1, /* Use non-standard SFD (Boolean) */
DWT_BR_6M8, /* Data rate. */
DWT_PHRMODE_STD, /* PHY header mode. */
(129 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
@@ -21,9 +22,13 @@
static uint8_t tx_sync_msg[14] = {0};
static uint8_t tx_final_msg[60] = {0};
static uint8_t tx_resp_msg[22] = {0};
+static uint8_t tx_nearpoll_msg[80] = {0};
+static uint8_t tx_nearresp_msg[80] = {0};
+static uint8_t tx_nearfinal_msg[80] = {0};
+
static uint8_t tx_near_msg[80] = {0};
-static uint32_t frame_seq_nb = 0;
+ uint32_t frame_seq_nb = 0, frame_seq_nb2 = 0;
static uint32_t status_reg = 0;
static uint8_t rx_buffer[100];
static uint64_t poll_tx_ts;
@@ -33,7 +38,7 @@
static uint64_t resp_tx_ts;
static uint64_t final_rx_ts;
static double tof;
-int32_t anchor_dist_last_frm[TAG_NUM_IN_SYS],his_dist[TAG_NUM_IN_SYS]; ;
+int32_t anchor_dist_last_frm[TAG_NUM_IN_SYS],his_dist[TAG_NUM_IN_SYS];
uint32_t tag_id = 0;
uint32_t tag_id_recv = 0;
uint32_t anc_id_recv = 0;
@@ -115,7 +120,9 @@
* For initialisation, DW1000 clocks must be temporarily set to crystal speed. After initialisation SPI rate can be increased for optimum
* performance. */
Reset_DW1000();//重启DW1000 /* Target specific drive of RSTn line into DW1000 low for a period. */
+ status_reg = dwt_read32bitreg(SYS_STATUS_ID);
dwt_initialise(DWT_LOADUCODE);//初始化DW1000
+ status_reg = dwt_read32bitreg(SYS_STATUS_ID);
Spi_ChangePrescaler(SPIx_PRESCALER_FAST); //设置为快速模式
/* Configure DW1000. See NOTE 6 below. */
@@ -134,7 +141,6 @@
void Dw1000_App_Init(void)
{
//g_com_map[DEV_ID] = 0x0b;
- tag_state=DISCPOLL;
tx_poll_msg[MESSAGE_TYPE_IDX]=POLL;
tx_resp_msg[MESSAGE_TYPE_IDX]=RESPONSE;
tx_final_msg[MESSAGE_TYPE_IDX]=FINAL;
@@ -144,8 +150,9 @@
memcpy(&tx_final_msg[TAG_ID_IDX], &dev_id, 2);
memcpy(&tx_resp_msg[ANCHOR_ID_IDX], &dev_id, 2);
memcpy(&tx_sync_msg[ANCHOR_ID_IDX], &dev_id, 2);
- memcpy(&tx_near_msg[ANCHOR_ID_IDX], &dev_id, 2);
- memcpy(&tx_near_msg[TAG_ID_IDX], &dev_id, 2);
+ memcpy(&tx_nearresp_msg[ANCHOR_ID_IDX], &dev_id, 2);
+ memcpy(&tx_nearpoll_msg[TAG_ID_IDX], &dev_id, 2);
+ memcpy(&tx_nearfinal_msg[TAG_ID_IDX], &dev_id, 2);
}
uint16_t Checksum_u16(uint8_t* pdata, uint32_t len)
{
@@ -158,24 +165,34 @@
}
u16 tag_time_recv[TAG_NUM_IN_SYS];
-u8 usart_send[25];
-u8 battary,button;
+u8 usart_send[150],usart_send_anc[100];
+u8 battary,button,tag_frequency,tag_slotpos;
extern uint8_t g_pairstart;
void tag_sleep_configuraion(void)
{
dwt_configuresleep(0x940, 0x7);
dwt_entersleep();
}
+
extern uint8_t g_start_send_flag;
u8 g_start_sync_flag;
void SyncPoll(u8 sync_seq)
-{
- g_start_sync_flag=1;
- dwt_forcetrxoff();
+{u8 result;
+ g_start_sync_flag=1; //中断模式，退出终端后，需要重新来过
+ dwt_forcetrxoff(); //关闭接收，以防在RX ON 状态
+
+
tx_sync_msg[SYNC_SEQ_IDX]=sync_seq;
+ memcpy(&tx_sync_msg[ANCHOR_ID_IDX],&dev_id,4);
dwt_writetxdata(sizeof(tx_sync_msg), tx_sync_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
dwt_writetxfctrl(sizeof(tx_sync_msg), 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE);
+ if(result==0)
+ {
+ while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
+ { };
+ }
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_TXFRS);//清楚标志位
}
uint16_t g_Resttimer;
uint8_t result;
@@ -190,10 +207,132 @@
u16 anclist_num=0,anclist_pos; //list 总数量和当前位置
u16 ancid_list[TAG_NUM_IN_SYS];
-u8 nearbase_num;
-u16 nearbaseid_list[10],mainbase_id;
-int32_t mainbase_dist,nearbase_distlist[10];
+u8 nearbase_num=0,last_nearbase_num,next_nearbase_num;
+u16 nearbaseid_list[MAX_NEARBASE_NUM],mainbase_id,true_nearbase_idlist[MAX_NEARBASE_NUM];
+int32_t mainbase_dist,nearbase_distlist[MAX_NEARBASE_NUM],true_nearbase_distlist[MAX_NEARBASE_NUM],true_exsistbase_list[MAX_NEARBASE_NUM];
uint8_t trygetnearmsg_times;
+u16 current_slotnum,total_slotnum,target_time,last_time;
+u32 rec_tagpos_binary;
+extern uint32_t tagpos_binary;
+void SetNextPollTime(u16 time)
+{
+ current_slotnum++;
+ if(current_slotnum==total_slotnum)
+ current_slotnum-=total_slotnum;
+ //time=5;
+ target_time=((current_slotnum*g_com_map[COM_INTERVAL])+time);
+
+ last_time=target_time;
+ if(target_time>=990&&target_time<992)
+ {
+ current_slotnum++;
+ target_time+=g_com_map[COM_INTERVAL];
+ tagslotpos=GetRandomSlotPos(rec_tagpos_binary|tagpos_binary);
+ tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
+ }
+ if(target_time>=1000)
+ {target_time-=1000;}
+ if(target_time<0)
+ {target_time+=1000;}
+
+}
+u8 FindNearBasePos(u16 baseid)
+{
+ u8 i;
+ for(i=0;i<last_nearbase_num;i++)
+ {
+ if(baseid==nearbaseid_list[i])
+ return i;
+ }
+ return i;
+}
+u8 recbase_num=0;
+#define CHANGE_BASE_THRESHOLD 5
+//void NearAncSelect(void)
+//{static u16 last_mainbase_id,change_base_count;
+// int32_t nearbase_mindist=99999, nearbase_minpos;
+// u8 i;
+// for(i=0;i<recbase_num-1;i++)
+// {
+// if(nearbase_mindist>nearbase_distlist[i])
+// {
+// nearbase_mindist=nearbase_distlist[i];
+// nearbase_minpos=i;
+// }
+// }
+// if(nearbase_mindist<mainbase_dist-THRESHOLD_CHANGE_MAINBASE_DIST)
+// {
+// if(last_mainbase_id==nearbaseid_list[nearbase_minpos])
+// {
+// change_base_count++;
+// if(change_base_count>CHANGE_BASE_THRESHOLD)
+// {
+// mainbase_id=last_mainbase_id;
+// tag_state=GETNEARMSG;
+// }
+// }else{
+// change_base_count=0;
+// }
+// last_mainbase_id=nearbaseid_list[nearbase_minpos];
+// }else{
+// change_base_count=0;
+// }
+//}
+uint8_t GetRandomValue(void)
+{
+ uint8_t random_value=0,temp_adc,i;
+ for(i=0;i<8;i++)
+ {
+ temp_adc=Get_ADC_Value();
+ random_value=random_value|((temp_adc&0x01)<<i);
+ }
+ return random_value;
+}
+u8 GetRandomSlotPos(uint32_t emptyslot)
+{
+ u8 i,temp_value;
+ temp_value = GetRandomValue();
+ for(i=temp_value%max_slotpos;i<max_slotpos;i++)
+ {
+ if(((emptyslot>>i)&0x1)==0)
+ {
+ return i;
+ }
+ }
+
+ for(i=1;i<max_slotpos;i++)
+ {
+ if(((emptyslot>>i)&0x1)==0)
+ {
+ return i;
+ }
+ }
+return max_slotpos-1;
+}
+dwt_rxdiag_t d1;
+u8 test=0;
+u8 anclost_times=0;
+u8 exsistbase_list[MAX_NEARBASE_NUM],report_num,get_newbase=0;
+u16 temp_sync_timer1,temp_sync_timer2;
+ double firstpath_power, rx_power;
+ double f1, f2, r1, r2;
+uint16_t F1,F2,F3,N,C;
+double B = 131072;
+double A = 121.74;
+double min_power;
+double LOS(dwt_rxdiag_t *dia) {
+ F1 = dia->firstPathAmp1;
+ F2 = dia->firstPathAmp2;
+ F3 = dia->firstPathAmp3;
+ N = dia->rxPreamCount;
+ C = dia->maxGrowthCIR;
+
+ firstpath_power=10* log10((F1*F1+F2*F2+F3*F3)/(N*N))-A;
+ rx_power=10*log10(C*B/(N*N))-A;
+
+ // min_power = - 10 * log10((F1 *F1 + F2 * F2 + F3 * F3) / (C *B));
+ return min_power;
+ }
void Poll(void)
{
uint32_t frame_len;
@@ -303,207 +442,11 @@
}
mainbase_id=minid;
}
-
-u8 FindNearBasePos(u16 baseid)
-{
- u8 i;
- for(i=0;i<nearbase_num;i++)
- {
- if(baseid==nearbaseid_list[i])
- return i;
- }
-}
-u8 recbase_num=0;
-#define CHANGE_BASE_THRESHOLD 5
-void NearAncSelect(void)
-{static u16 last_mainbase_id,change_base_count;
- int32_t nearbase_mindist=99999, nearbase_minpos;
- u8 i;
- for(i=0;i<recbase_num-1;i++)
- {
- if(nearbase_mindist>nearbase_distlist[i])
- {
- nearbase_mindist=nearbase_distlist[i];
- nearbase_minpos=i;
- }
- }
- if(nearbase_mindist<mainbase_dist-THRESHOLD_CHANGE_MAINBASE_DIST)
- {
- if(last_mainbase_id==nearbaseid_list[nearbase_minpos])
- {
- change_base_count++;
- if(change_base_count>CHANGE_BASE_THRESHOLD)
- {
- mainbase_id=last_mainbase_id;
- tag_state=GETNEARMSG;
- }
- }else{
- change_base_count=0;
- }
- last_mainbase_id=nearbaseid_list[nearbase_minpos];
- }else{
- change_base_count=0;
- }
-}
-void NearPoll(void)
-{
- static u8 mainbase_lost_count=0,flag_finalsend;
- uint32_t temp1,temp2,dw_systime;
- uint32_t frame_len;
- uint32_t final_tx_time;
- u32 start_poll;
- u8 i,getsync_flag=0,timeout;
- dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
- tag_succ_times = 0;
- tx_near_msg[BATTARY_IDX] = Get_Battary();
- tx_near_msg[BUTTON_IDX] = !READ_KEY0;
- tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
- tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
- memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
- tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
- dwt_writetxdata(13+2*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
- dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
-
- for(i=0;i<nearbase_num;i++)
- nearbase_distlist[i]=0xffff;
-
- flag_finalsend=0;
- neartimout_timer=0;
- recbase_num=0;
- timeout=nearbase_num/4+2;
- mainbase_dist=100000;
- mainbase_lost_count++;
- while(neartimout_timer<timeout)
- {
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
- {
- if(flag_finalsend)
- {
- dw_systime=dwt_readsystimestamphi32();
- if(dw_systime>temp1&&dw_systime<temp2)
- {
- flag_finalsend=0;
- dwt_forcetrxoff();
- dwt_setdelayedtrxtime(final_tx_time);
- result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- break;
- }
- }
- if(neartimout_timer>timeout)
- break;
- };
- if(status_reg==0xffffffff)
- {
- NVIC_SystemReset();
- }
- if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
- {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
- frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
- dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
- dwt_rxenable(0);//打开接收
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
- { u16 rec_nearbaseid,rec_nearbasepos;
- poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
- resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
- recbase_num++;
- memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
- if(rec_nearbaseid==mainbase_id)
- {
- //////////////////////////////////时间同步
- memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
- memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
- memcpy(&tagslotpos,&rx_buffer[TAGSLOTPOS],2);
- tmp_time=tmp_time+450;
- if(tmp_time>999)
- {
- tmp_time-=999;
- sync_timer++;
- if(sync_timer>=1010)
- {sync_timer=0;}
- }
- TIM3->CNT=tmp_time;
- if(tagslotpos>max_slotpos)
- tagslotpos=tagslotpos%(max_slotpos+1);
- tyncpoll_time=(tagslotpos-1)*slottime;
- ////////////////////////////
- mainbase_lost_count=0;
- flag_finalsend=1;
- memcpy(&mainbase_dist,&rx_buffer[DIST_IDX],4);
- final_tx_time = (resp_rx_ts + ((RESP_RX_TO_FINAL_TX_DLY_UUS+DELAY_BETWEEN_TWO_FRAME_UUS*nearbase_num+500) * UUS_TO_DWT_TIME)) >> 8;
- temp1=final_tx_time-((350*UUS_TO_DWT_TIME)>>8);
- temp2=final_tx_time+((100*UUS_TO_DWT_TIME)>>8);
- // dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
- tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
- dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
- usart_send[2] = 1;//正常模式
- usart_send[3] = 17;//数据段长度
- usart_send[4] = frame_seq_nb;//数据段长度
- memcpy(&usart_send[5],&dev_id,2);
- memcpy(&usart_send[7],&rec_nearbaseid,2);
- memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
- usart_send[13] = battary;
- usart_send[14] = button;
- checksum = Checksum_u16(&usart_send[2],17);
- memcpy(&usart_send[19],&checksum,2);
- UART_PushFrame(usart_send,21);
- //result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- }else{
- rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], resp_rx_ts);
- memcpy(&nearbase_distlist[rec_nearbasepos],&rx_buffer[DIST_IDX],4);
- dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
- LED0_BLINK;
- usart_send[2] = 1;//正常模式
- usart_send[3] = 17;//数据段长度
- usart_send[4] = frame_seq_nb;//数据段长度
- memcpy(&usart_send[5],&dev_id,2);
- memcpy(&usart_send[7],&rec_nearbaseid,2);
- memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
- usart_send[13] = battary;
- usart_send[14] = button;
- checksum = Checksum_u16(&usart_send[2],17);
- memcpy(&usart_send[19],&checksum,2);
- UART_PushFrame(usart_send,21);
-
- //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- // result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
- }
- }
- }
- dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- }
- if(mainbase_lost_count>5)
- {
- tag_state=DISCPOLL;
- }
- NearAncSelect();
-// if(result==0)
-// {while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
-// { };
-//
-// }
-// else
-// {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
-// }
-
-}
-
+u8 nearmsg_mainbase=0,rec_tagpos_emptylist[32];
void GetNearMsg(void)
{
u32 start_poll,frame_len;
+
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
@@ -530,14 +473,318 @@
dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_MSG&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
{
- nearbase_num=rx_buffer[NEARBASENUM_INDEX];
- tagslotpos=rx_buffer[TAGSLOTPOS];
- memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
- slottime=ceil((nearbase_num+2)*0.3)+1;
+ next_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
+ tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
+ //tagslotpos=rx_buffer[TAGSLOTPOS];
+ memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],next_nearbase_num*2);
+ //slottime=ceil((nearbase_num+2)*0.4)+2;
tyncpoll_time=tagslotpos*slottime;
tag_state=NEARPOLL;
+ }else{
+ tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
}
+ }else{
+ tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
}
+
+}
+ void NearPoll(void)
+{
+ static u8 mainbase_lost_count=0,flag_finalsend,flag_rxon;
+ uint32_t temp1,temp2,dw_systime;
+ uint32_t frame_len;
+ uint32_t final_tx_time;
+ u32 start_poll;
+ u8 i,j,getsync_flag=0,timeout;
+// printf("%d",sync_timer);
+ dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+ tag_succ_times = 0;
+ GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
+ if(next_nearbase_num>=MAX_NEARBASE_NUM)
+ {
+ next_nearbase_num = MAX_NEARBASE_NUM-1;
+ }
+ //nearbase_num=0;
+ last_nearbase_num=next_nearbase_num;
+ nearbase_num=next_nearbase_num;
+ recbase_num=0;
+ tx_nearpoll_msg[BATTARY_IDX] = Get_Battary();
+ tx_nearpoll_msg[BUTTON_IDX] = !READ_KEY0;
+ tx_nearpoll_msg[SEQUENCE_IDX] = frame_seq_nb++;
+ tx_nearpoll_msg[NEARBASENUM_INDEX] = nearbase_num;
+ memcpy(&tx_nearpoll_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
+ tx_nearpoll_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
+ memcpy(&tx_nearpoll_msg[ANCHOR_ID_IDX],&mainbase_id,2);
+ dwt_writetxdata(13+2*nearbase_num, tx_nearpoll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+
+ flag_finalsend=0;
+ flag_rxon=1;
+ neartimout_timer=0;
+ get_newbase=0;
+ timeout=ceil((float)nearbase_num*SLOT_SCALE)+2;
+ //timeout=5;
+ mainbase_dist=100000;
+ mainbase_lost_count++;
+ while(neartimout_timer<timeout)
+ {
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
+ {
+ if(flag_finalsend)
+ {
+ dw_systime=dwt_readsystimestamphi32();
+ if(dw_systime>temp1&&dw_systime<temp2)
+ {
+ flag_finalsend=0;
+ flag_rxon=0;
+ dwt_forcetrxoff();
+ dwt_setdelayedtrxtime(final_tx_time);
+ result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ #ifdef DEBUG_INF
+ USART_putc(0x33);
+ #endif
+ break;
+ }
+ }
+ if(neartimout_timer>timeout)
+ break;
+ };
+ if(status_reg==0xffffffff)
+ {
+ NVIC_SystemReset();
+ }
+ if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
+ {
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+ frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
+ dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+ dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
+ dwt_rxenable(0);//打开接收
+ if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ { u16 rec_nearbaseid,rec_nearbasepos;
+ int32_t temp_dist;
+ poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
+ resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
+ recbase_num++;
+ memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
+
+ if(rec_nearbaseid==mainbase_id)
+ {
+ //////////////////////////////////时间同步
+ temp_sync_timer2=sync_timer;
+ memcpy(&temp_sync_timer1,&rx_buffer[ANCTIMEMS],2);
+ memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
+
+
+ if(g_com_map[DEV_ROLE]!=0)
+ {
+ sync_timer=temp_sync_timer1;
+//// memcpy(&tagslotpos,&rx_buffer[TAGSLOTPOS],2);
+//
+
+ tmp_time=tmp_time+650;
+ if(tmp_time>999)
+ {
+ tmp_time-=999;
+ sync_timer++;
+ if(sync_timer>=1000)
+ {sync_timer=0;}
+ }
+ TIM3->CNT=tmp_time;
+ }
+ current_slotnum=temp_sync_timer1/g_com_map[COM_INTERVAL];
+// if(tagslotpos>max_slotpos)
+// tagslotpos=tagslotpos%(max_slotpos+1);
+// tyncpoll_time=(tagslotpos-1)*slottime;
+ ////////////////////////////
+ #ifdef DEBUG_INF
+ USART_putc(0x31);
+ #endif
+ rec_nearbasepos=0;
+
+ memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
+ mainbase_dist = temp_dist;
+ if(temp_dist!=0x1ffff)
+ exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
+
+ mainbase_lost_count=0;
+ flag_finalsend=1;
+ final_tx_time = (resp_rx_ts + ((RESP_RX_TO_FINAL_TX_DLY_UUS+DELAY_BETWEEN_TWO_FRAME_UUS*nearbase_num+500) * UUS_TO_DWT_TIME)) >> 8;
+ temp1=final_tx_time-((350*UUS_TO_DWT_TIME)>>8);
+ temp2=final_tx_time+((100*UUS_TO_DWT_TIME)>>8);
+ // dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+ final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
+ final_msg_set_ts(&tx_nearfinal_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
+ final_msg_set_ts(&tx_nearfinal_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
+ final_msg_set_ts(&tx_nearfinal_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
+ tx_nearfinal_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
+ dwt_writetxdata(28+nearbase_num*4, tx_nearfinal_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
+ memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
+
+ }else{
+ rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
+ if(rec_nearbasepos>=last_nearbase_num) //发现新的基站
+ {
+ get_newbase=1;
+ nearbase_num++;
+ nearbaseid_list[rec_nearbasepos] = rec_nearbaseid;
+ memcpy(&tx_nearfinal_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
+ }
+ #ifdef DEBUG_INF
+ USART_putc(0x32);
+ #endif
+ memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
+ nearbase_distlist[rec_nearbasepos]=temp_dist;
+
+ if(temp_dist!=0x1ffff)
+ exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
+
+ final_msg_set_ts(&tx_nearfinal_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
+ dwt_writetxdata(28+nearbase_num*4, tx_nearfinal_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
+ LED0_BLINK;
+// memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
+// tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
+ if(temp_dist!=0x1ffff)
+ {
+ #ifdef TAG_OUTPUT
+ #ifndef USART_INTEGRATE_OUTPUT
+ usart_send[2] = 1;//正常模式
+ usart_send[3] = 17;//数据段长度
+ usart_send[4] = frame_seq_nb;//数据段长度
+ if(g_com_map[DEV_ROLE])
+ {
+ memcpy(&usart_send[5],&dev_id,2);
+ memcpy(&usart_send[7],&rec_nearbaseid,2);
+ }else{
+ memcpy(&usart_send[5],&rec_nearbaseid,2);
+ memcpy(&usart_send[7],&dev_id,2);
+ }
+ memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
+ usart_send[13] = battary;
+ usart_send[14] = button;
+ checksum = Checksum_u16(&usart_send[2],17);
+ memcpy(&usart_send[19],&checksum,2);
+ UART_PushFrame(usart_send,21);
+ #endif
+ #endif
+ //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+ // result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
+ }
+ }
+ }
+ }else{
+ #ifdef DEBUG_INF
+ printf("response包失败：%x/n",status_reg);
+ #endif
+ dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ if(flag_rxon)
+ {dwt_rxenable(0);
+ }
+ }
+ }
+ GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_RESET);
+// if(result==0)
+// {
+// while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
+// { };
+// }
+// dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_TXFRS);//清楚标志位
+
+ dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ nearbase_num=recbase_num;
+ j=0;
+ if(exsistbase_list[0]==0)
+ {
+// u8 temp_adc,random_value;
+// random_value=0;
+// for(i=0;i<8;i++)
+// {
+// temp_adc=Get_ADC_Value();
+// random_value=random_value|((temp_adc&0x01)<<i);
+// }
+ tagslotpos=GetRandomSlotPos(rec_tagpos_binary|tagpos_binary);
+ tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
+ tag_state=GETNEARMSG;
+ }
+ // tyncpoll_time=0;
+ next_nearbase_num=0;
+ for(i=0;i<last_nearbase_num+get_newbase;i++)
+ {
+ if(exsistbase_list[i]>0)
+ {
+ next_nearbase_num++;
+ true_exsistbase_list[j]=exsistbase_list[i];
+ true_nearbase_idlist[j]=nearbaseid_list[i];
+ true_nearbase_distlist[j++]=nearbase_distlist[i];
+ exsistbase_list[i]--;
+ }
+ }
+
+ if(recbase_num<3)
+ {next_nearbase_num=next_nearbase_num;}
+ last_nearbase_num = next_nearbase_num;
+ for(i=0;i<last_nearbase_num-1;i++)
+ {
+ for(j=0;j<last_nearbase_num-1;j++)
+ {
+ if(true_nearbase_distlist[j]>true_nearbase_distlist[j+1])
+ {
+ u32 temp_dist,temp_id,temp_exsis;
+ temp_dist=true_nearbase_distlist[j];
+ temp_id = true_nearbase_idlist[j];
+ temp_exsis=true_exsistbase_list[i];
+ true_nearbase_distlist[j]=true_nearbase_distlist[j+1];
+ true_nearbase_idlist[j]=true_nearbase_idlist[j+1];
+ true_exsistbase_list[j]=true_exsistbase_list[j+1];
+
+ true_nearbase_distlist[j+1]=temp_dist;
+ true_nearbase_idlist[j+1]=temp_id;
+ true_exsistbase_list[j+1]=temp_exsis;
+ }
+ }
+ }
+
+ report_num=0;
+
+ for(i=0;i<MAX_NEARBASE_NUM;i++)
+ {
+ nearbase_distlist[i]=0x1ffff;
+ }
+
+ // printf("%d,%d",temp_sync_timer2,temp_sync_timer1);
+ #ifdef USART_INTEGRATE_OUTPUT
+ usart_send[2] = 4;//正常模式
+ usart_send[3] = report_num*6+2;//正常模式
+ checksum = Checksum_u16(&usart_send[2],report_num*6+2);
+ memcpy(&usart_send[4+report_num*6],&checksum,2);
+ UART_PushFrame(usart_send,6+report_num*6);
+ #endif
+ #ifdef DEBUG_INF
+ printf("序号：%d,基站数量：%d/n",(frame_seq_nb-1)&0xff,nearbase_num);
+ #endif
+// if(mainbase_lost_count>5)
+// {
+// //tag_state=DISCPOLL;
+// }
+// NearAncSelect();
+// if(recbase_num<g_com_map[MIN_REPORT_ANC_NUM] )
+// {
+// anclost_times++;
+// if(anclost_times>3)
+// {
+// tagslotpos=poll_tx_ts%(max_slotpos+1);
+// }
+// }else{
+// anclost_times=0;
+// }
+dwt_forcetrxoff();
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
}
void Tag_App(void)//发送模式(TAG标签)
@@ -545,29 +792,26 @@
//LED0_ON;
dwt_forcetrxoff();
g_Resttimer=0;
+ GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
switch(tag_state)
{
case DISCPOLL:
- Poll();
+ Poll();
break;
case GETNEARMSG:
- // if(trygetnearmsg_times--!=0)
- {GetNearMsg();
- }
-// else{
-// tag_state=DISCPOLL;
-// }
-
+ GetNearMsg();
break;
case NEARPOLL:
- GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_SET);
- NearPoll();
- GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_RESET);
+ NearPoll();
break;
}
+
+ SetNextPollTime(tyncpoll_time);
+ g_start_send_flag = 0;
+ GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_RESET);
}
-int8_t correction_time;
+int8_t correction_time,new_tagid=0;
extern uint8_t sync_seq;
u16 taglist_num=0,taglist_pos;
u16 tagid_list[TAG_NUM_IN_SYS];
@@ -591,12 +835,13 @@
for(i=0;i<taglist_num;i++)
{
if(memcmp(&tagid,&tagid_list[i],2)==0)
- return i+1;
+ break;
}
- return 0;
+ return i;
}
uint32_t frame_len;
uint32_t resp_tx_time;
+uint8_t rec_nearbase_num,anc_report_num;
void Anchor_RecPoll(void)
{
tmp_time=TIM3->CNT;
@@ -618,9 +863,8 @@
dwt_writetxfctrl(sizeof(tx_resp_msg), 0);//设定发送长度
result = dwt_starttx(DWT_START_TX_DELAYED | DWT_RESPONSE_EXPECTED);//延迟发送，等待接收
- battary = rx_buffer[BATTARY_IDX];
- button = rx_buffer[BUTTON_IDX];
- frame_seq_nb = rx_buffer[SEQUENCE_IDX];
+
+ frame_seq_nb2 = rx_buffer[SEQUENCE_IDX];
if(result==0)
{
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))///不断查询芯片状态直到接收成功或者出现错误
@@ -660,7 +904,7 @@
LED0_BLINK; //每成功一次通讯则闪烁一次
dis_after_filter=dist_cm;
hex_dist = dist_cm+(int16_t)g_com_map[DIST_OFFSET];
- if(abs(hex_dist-his_dist[tag_id_recv-TAG_ID_START])<1000)
+ if(abs(hex_dist-his_dist[taglist_pos])<1000)
{
tagdist_list[taglist_pos] = hex_dist;
}
@@ -670,30 +914,79 @@
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
-u8 misdist_num;
-void Anchor_RecNearPoll(u8 ancrec_nearbasepos) //0 mainbase 1 first near_base
+uint32_t time_monitor[10];
+extern uint16_t configremotetagID;
+extern u8 remotetag_paralen;
+u8 finalsend=0;
+u8 misdist_num[TAG_NUM_IN_SYS],seize_anchor,waittagconfig_reponse,motorstate=0;
+u8 Anchor_RecNearPoll(u8 ancrec_nearbasepos) //0 mainbase 1 first near_base
{
+
tmp_time=TIM3->CNT;
- memcpy(&tx_near_msg[ANCTIMEMS],&sync_timer,2);
- memcpy(&tx_near_msg[ANCTIMEUS],&tmp_time,2);
- memcpy(&tx_near_msg[TAGSLOTPOS],&taglist_pos,2);
- memcpy(&tx_near_msg[TAG_ID_IDX],&tag_id_recv,2);
+ memcpy(&tx_nearresp_msg[NR_NEARSWITCH_DISTANCE],&g_com_map[NEARSWITCH_DISTANCE_INDEX],2);
+ memcpy(&tx_nearresp_msg[ANCTIMEMS],&sync_timer,2);
+ memcpy(&tx_nearresp_msg[ANCTIMEUS],&tmp_time,2);
+ memcpy(&tx_nearresp_msg[TAGSLOTPOS],&taglist_pos,2);
+ memcpy(&tx_nearresp_msg[TAG_ID_IDX],&tag_id_recv,2);
poll_rx_ts = get_rx_timestamp_u64();//获得Poll包接收时间T2
- resp_tx_time = (poll_rx_ts + ((POLL_RX_TO_RESP_TX_DLY_UUS+ancrec_nearbasepos*DELAY_BETWEEN_TWO_FRAME_UUS) * UUS_TO_DWT_TIME)) >> 8;//计算Response发送时间T3。
+ resp_tx_time = (poll_rx_ts + ((POLL_RX_TO_RESP_TX_DLY_UUS+(ancrec_nearbasepos)*DELAY_BETWEEN_TWO_FRAME_UUS) * UUS_TO_DWT_TIME)) >> 8;//计算Response发送时间T3。
dwt_setdelayedtrxtime(resp_tx_time);//设置Response发送时间T3
- dwt_setrxaftertxdelay(RESP_TX_TO_FINAL_RX_DLY_UUS+(nearbase_num-ancrec_nearbasepos)*DELAY_BETWEEN_TWO_FRAME_UUS);//设置发送完成后开启接收延迟时间
+ dwt_setrxaftertxdelay(RESP_TX_TO_FINAL_RX_DLY_UUS+(rec_nearbase_num+1-ancrec_nearbasepos)*DELAY_BETWEEN_TWO_FRAME_UUS);//设置发送完成后开启接收延迟时间
dwt_setrxtimeout(FINAL_RX_TIMEOUT_UUS);//接收超时时间
+ dwt_readdiagnostics(&d1);
+
+ if(new_tagid)
+ {
+ tagdist_list[taglist_pos]=0x1ffff;
+ memcpy(&tx_nearresp_msg[DIST_IDX], &tagdist_list[taglist_pos], 4);
+ }else{
+ memcpy(&tx_nearresp_msg[DIST_IDX], &tagdist_list[taglist_pos], 4);
+ }
+ tx_nearresp_msg[MAINBASE_INDEX]=flag_syncbase;
+ tx_nearresp_msg[MESSAGE_TYPE_IDX]=NEAR_RESPONSE;
+ tx_nearresp_msg[MOTORSTATE_INDEX]=(remotesend_state<<4)|motorstate;
+ waittagconfig_reponse=0;
+ finalsend = 0;
+ if(pwtag.remain_time>0)
+ {uint8_t i;
+ for(i=0;i<pwtag.groupnum;i++)
+ {
+ if(pwtag.groupid[i][0]<=tag_id_recv&&tag_id_recv<=pwtag.groupid[i][1])
+ {
+ remotesend_state=1;
+ tx_nearresp_msg[MOTORSTATE_INDEX]=(remotesend_state<<4)|motorstate;
+ remotetag_paralen = 2+3;
+ remotetag_para[0] = 2;
+ remotetag_para[1] = pwtag.index;
+ remotetag_para[2] = 2;
+ memcpy(&remotetag_para[3],&pwtag.group_interval[i],2);
+ memcpy(&tx_nearresp_msg[REMOTEPARA_INDEX],remotetag_para,remotetag_paralen);
+ dwt_writetxdata(24+remotetag_paralen, tx_nearresp_msg, 0);//写入发送数据
+ dwt_writetxfctrl(24+remotetag_paralen, 0);//设定发送长度
+ remotesend_state=0;
+ finalsend = 1;
+ break;
+ }
+ }
+ }
+
+ if(finalsend == 0)
+ {
+ dwt_writetxdata(24, tx_nearresp_msg, 0);//写入发送数据
+ dwt_writetxfctrl(24, 0);//设定发送长度
+ }
+
+// if(remotesend_state&&tag_id_recv==configremotetagID)
+// {
+// memcpy(&tx_nearresp_msg[REMOTEPARA_INDEX],remotetag_para,remotetag_paralen);
+// dwt_writetxdata(22+remotetag_paralen, tx_nearresp_msg, 0);//写入发送数据
+// dwt_writetxfctrl(22+remotetag_paralen, 0);//设定发送长度
+// waittagconfig_reponse=1;
+// }else{
- memcpy(&tx_near_msg[DIST_IDX], &tagdist_list[taglist_pos], 4);
- tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_RESPONSE;
- dwt_writetxdata(20, tx_near_msg, 0);//写入发送数据
- dwt_writetxfctrl(20, 0);//设定发送长度
result = dwt_starttx(DWT_START_TX_DELAYED | DWT_RESPONSE_EXPECTED);//延迟发送，等待接收
- battary = rx_buffer[BATTARY_IDX];
- button = rx_buffer[BUTTON_IDX];
- frame_seq_nb = rx_buffer[SEQUENCE_IDX];
if(result==0)
{
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_sync_flag)///不断查询芯片状态直到接收成功或者出现错误
@@ -701,11 +994,17 @@
}else{
result++;
}
+
if (status_reg & SYS_STATUS_RXFCG)//接收成功
{
+
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK;//数据长度
dwt_readrxdata(rx_buffer, frame_len, 0);//读取接收数据
+ if(seize_anchor&&memcmp(&rx_buffer[ANCHOR_ID_IDX],&dev_id,2)) //抢占anchor 失败
+ {
+ return 1;
+ }
if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_FINAL&&!memcmp(&rx_buffer[TAG_ID_IDX],&tag_id_recv,2)) //判断是否为Final包
{
uint32_t poll_tx_ts, resp_rx_ts, final_tx_ts;
@@ -714,6 +1013,10 @@
int64_t tof_dtu;
resp_tx_ts = get_tx_timestamp_u64();//获得response发送时间T3
final_rx_ts = get_rx_timestamp_u64();//获得final接收时间T6
+
+// dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
+// dwt_rxenable(0);//打开接收
+
final_msg_get_ts(&rx_buffer[FINAL_MSG_POLL_TX_TS_IDX], &poll_tx_ts);//从接收数据中读取T1，T4，T5
final_msg_get_ts(&rx_buffer[FINAL_MSG_RESP_RX_NEARBASE_IDX+ancrec_nearbasepos*4], &resp_rx_ts);
final_msg_get_ts(&rx_buffer[FINAL_MSG_FINAL_TX_TS_IDX], &final_tx_ts);
@@ -721,6 +1024,7 @@
poll_rx_ts_32 = (uint32_t)poll_rx_ts;//使用32位数据计算
resp_tx_ts_32 = (uint32_t)resp_tx_ts;
final_rx_ts_32 = (uint32_t)final_rx_ts;
+ time_monitor[1] = sync_timer*1000+TIM3->CNT;
Ra = (double)(resp_rx_ts - poll_tx_ts);//Tround1 = T4 - T1
Rb = (double)(final_rx_ts_32 - resp_tx_ts_32);//Tround2 = T6 - T3
Da = (double)(final_tx_ts - resp_rx_ts);//Treply2 = T5 - T4
@@ -729,83 +1033,133 @@
tof = tof_dtu * DWT_TIME_UNITS;
distance = tof * SPEED_OF_LIGHT;//距离=光速*飞行时间
dist_no_bias = distance - dwt_getrangebias(config.chan, (float)distance, config.prf); //距离减去矫正系数
- dist_cm = dist_no_bias * 100; //dis 为单位为cm的距离
+ dist_cm = dist_no_bias * 100; //dis 为单位为cm的距离
+ dwt_readdiagnostics(&d1);
+// time_monitor[2] = sync_timer*1000+TIM3->CNT;
+ LOS(&d1);
+ time_monitor[3] = sync_timer*1000+TIM3->CNT;
/*--------------------------以下为非测距逻辑------------------------*/
//dist_cm=33000;
-
+ GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_RESET);
LED0_BLINK; //每成功一次通讯则闪烁一次
dis_after_filter=dist_cm;
hex_dist = dist_cm+(int16_t)g_com_map[DIST_OFFSET];
- if(hex_dist>-1000&&hex_dist<100000)
+ g_flag_Taggetdist[taglist_pos]=0;
+ if(hex_dist>-1000&&hex_dist<200000)
{
- if(abs(hex_dist-his_dist[taglist_pos])<1500||misdist_num>3)
+ if(abs(hex_dist-his_dist[taglist_pos])<1500||misdist_num[taglist_pos]>3)
{
- misdist_num=0;
+ misdist_num[taglist_pos]=0;
tagdist_list[taglist_pos] = hex_dist;
- his_dist[taglist_pos]=hex_dist;
- usart_send[2] = 1;//正常模式
+ his_dist[taglist_pos]=hex_dist;
+ g_Tagdist[taglist_pos]=hex_dist;
+ #ifndef USART_INTEGRATE_OUTPUT
+ usart_send[2] = 1;//正常模式
usart_send[3] = 17;//数据段长度
- usart_send[4] = frame_seq_nb;//数据段长度
+ usart_send[4] = frame_seq_nb2;//数据段长度
memcpy(&usart_send[5],&tag_id_recv,2);
memcpy(&usart_send[7],&dev_id,2);
memcpy(&usart_send[9],&tagdist_list[taglist_pos],4);
usart_send[13] = battary;
usart_send[14] = button;
+ usart_send[15] = firstpath_power;
+ usart_send[16] = (rx_power-firstpath_power)*10;
+ usart_send[17] = tag_frequency;
+ usart_send[18] = tag_slotpos;
checksum = Checksum_u16(&usart_send[2],17);
memcpy(&usart_send[19],&checksum,2);
- UART_PushFrame(usart_send,21);
+ // UART_PushFrame(usart_send,21);
+ #else
+ memcpy(&usart_send_anc[4+6*anc_report_num],&tag_id_recv,2);
+ memcpy(&usart_send_anc[6+6*anc_report_num],&tagdist_list[taglist_pos],4);
+ anc_report_num++;
+ #endif
+ #ifdef DEBUG_INF
+ printf("序号：%d\r\n",frame_seq_nb2);
+ #endif
}else{
- misdist_num++;
+ // printf("%d",hex_dist);
+ misdist_num[taglist_pos]++;
}
}
+ if(rx_buffer[TAGCONFIGSUCCESS_INDEX]==1)
+ {
+
+ remotesend_state = 0;
+ usart_send[2] = 7;//正常模式
+ usart_send[3] = 5;//数据段长度
+ memcpy(&usart_send[4],&tag_id_recv,2);
+ usart_send[6] = 1;//数据段长度
+ checksum = Checksum_u16(&usart_send[2],5);
+ memcpy(&usart_send[7],&checksum,2);
+ UART_PushFrame(usart_send,9);
+ }
}
}else{
+ #ifdef DEBUG_INF
+ printf("final包失败：%x/n",status_reg);
+ #endif
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
+extern int32_t intheight;
+extern u16 synclost_count;
+uint32_t current_syncid=0xffffffff,synclost_timer;
+extern u8 flag_syncbase,waitsync_flag;
+u8 tagpos_rec[50],tagpos_send[50],ancidlist_num;
+u16 ancidlist_rec[20],ancidlist_send[20];
+u16 recnearbaselist_id[30];
+int32_t recnearbaselist_dist[30];
+int16_t rec_tagheight;
void Anchor_App(void)
{
+
u8 send_len,i;
u16 tempid;
+ uint32_t rec_syncid;
+
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
g_start_sync_flag=0;
+
dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
dwt_rxenable(0);//打开接收
+// GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
{
IdleTask();
- g_Resttimer=0;
};
-
+//GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_RESET);
if (status_reg & SYS_STATUS_RXFCG)//成功接收
{ u16 tag_recv_interval;
+ float temp_tagpos;
+ time_monitor[0] = sync_timer*1000+TIM3->CNT;
+ g_Resttimer=0;
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG);//清除标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFL_MASK_1023;//获得接收数据长度
dwt_readrxdata(rx_buffer, frame_len, 0);//读取接收数据
- //将收到的tag_id分别写入各次通讯的包中，为多标签通讯服务，防止一次通讯中接收到不同ID标签的数据
- //tag_id_recv = rx_buffer[TAG_ID_IDX];
- memcpy(&tag_id_recv,&rx_buffer[TAG_ID_IDX],2);
memcpy(&anc_id_recv,&rx_buffer[ANCHOR_ID_IDX],2);
- taglist_pos=CmpTagInList(tag_id_recv);
- if(taglist_pos==0)
- {
- tagid_list[taglist_num++]=tag_id_recv;
- taglist_pos=taglist_num;
- }
- tagofflinetime[taglist_pos-1]=0;
+ //将收到的tag_id分别写入各次通讯的包中，为多标签通讯服务，防止一次通讯中接收到不同ID标签的数据
+ memcpy(&tag_id_recv,&rx_buffer[TAG_ID_IDX],2);
switch(rx_buffer[MESSAGE_TYPE_IDX])
{
+ uint16_t checksum;
case POLL:
if (anchor_type == rx_buffer[ANC_TYPE_IDX])
Anchor_RecPoll();
break;
- case SYNC:
- if(rx_buffer[SYNC_SEQ_IDX]<sync_seq)
- {
- sync_seq=rx_buffer[SYNC_SEQ_IDX]+1;
- TIM3->CNT = sync_seq*325%1000+15;
- sync_timer = sync_seq*325/1000;
- SyncPoll(sync_seq);
- }
+ case SYNC:
+ memcpy(&rec_syncid,&rx_buffer[ANCHOR_ID_IDX],4);
+ if(anc_id_recv==g_com_map[SYNCBASEID])
+ {
+ synclost_count = 0;
+ flag_syncbase=0;
+ sync_seq=rx_buffer[SYNC_SEQ_IDX]+1;
+ TIM3->CNT = (sync_seq*325%1000)-80;
+ sync_timer = (sync_seq*325/1000);
+ synclost_timer=0;
+ if(g_com_map[BASESYNCSEQ]==2)
+ SyncPoll(sync_seq);
+ }
break;
case NEAR_MSG:
if(anc_id_recv==dev_id)
@@ -813,35 +1167,140 @@
rx_buffer[TAGSLOTPOS]=taglist_pos;
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
memcpy(&tx_near_msg[TAG_ID_IDX],&tag_id_recv,2);
+ memcpy(&tx_near_msg[NEARMSG_EMPTYSLOTPOS_INDEX],&tagpos_binary,4);
+ ancidlist_num=g_com_map[NEARBASE_NUM];
tx_near_msg[NEARBASENUM_INDEX]=g_com_map[NEARBASE_NUM];
memcpy(&tx_near_msg[NEARBASEID_INDEX],&g_com_map[NEARBASE_ID1],g_com_map[NEARBASE_NUM]*2);
- send_len=11+g_com_map[NEARBASE_NUM]*2+2;
+ send_len=21+ancidlist_num*2;
dwt_writetxdata(send_len, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
dwt_writetxfctrl(send_len, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE);
}
break;
+ case REG_POLL:
+ for(i=0;i<MAX_REGTAGNUM;i++)
+ {
+ if(tag_id_recv==regtag_map.tagid[i]&®tag_map.remain_time[i]>0)
+ {
+ tx_near_msg[REGR_TAGSLOTPOS_INDEX]=regtag_map.tag_slotpos[i];
+ tx_near_msg[REGR_TAGFREQ_INDEX] = regtag_map.tag_frequency[i];
+ memcpy(&tx_near_msg[TAG_ID_IDX],&tag_id_recv,2);
+ memcpy(&tx_near_msg[ANCHOR_ID_IDX],&dev_id,2);
+ tx_near_msg[MESSAGE_TYPE_IDX] = REG_RESPONSE;
+ ancidlist_num=g_com_map[NEARBASE_NUM];
+ tx_near_msg[NEARBASENUM_INDEX]=g_com_map[NEARBASE_NUM];
+ memcpy(&tx_near_msg[NEARBASEID_INDEX],&g_com_map[NEARBASE_ID1],g_com_map[NEARBASE_NUM]*2);
+ send_len=21+ancidlist_num*2;
+ dwt_writetxdata(send_len, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(send_len, 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE);
+ regtag_map.tagid[i] = 0;
+ break;
+ }
- case NEAR_POLL:
- nearbase_num=rx_buffer[NEARBASENUM_INDEX];
- if(anc_id_recv==dev_id)
+ }
+ if(i==MAX_REGTAGNUM)
+ {
+ dwt_readdiagnostics(&d1);
+ LOS(&d1);
+ usart_send[2]=0x0a;
+ usart_send[3]=20;
+ memcpy(&usart_send[4],&dev_id,2);
+ memcpy(&usart_send[6],&tag_id_recv,2);
+ memcpy(&usart_send[8],&rx_buffer[10],9);
+ usart_send[17] = firstpath_power;
+ checksum = Checksum_u16(&usart_send[2],20);
+ memcpy(&usart_send[22],&checksum,2);
+ UART_PushFrame(usart_send,24);
+ }
+ break;
+ case NEAR_POLL:
+ // GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_SET);
+
+ memcpy(&tag_id_recv,&rx_buffer[TAG_ID_IDX],2);
+ taglist_pos=CmpTagInList(tag_id_recv);
+ if(taglist_pos==taglist_num)
{
- Anchor_RecNearPoll(0);
+ taglist_pos=taglist_num;
+ tagid_list[taglist_num++]=tag_id_recv;
+
+ new_tagid=1;
}else{
- for(i=0;i<nearbase_num;i++)
+ new_tagid=0;
+ }
+ tagofflinetime[taglist_pos]=0;
+ temp_tagpos=round((float)(sync_timer%g_com_map[COM_INTERVAL])/slottime);
+ tagpos_rec[(u8)temp_tagpos]=1;
+ rec_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ battary = rx_buffer[BATTARY_IDX];
+ button = rx_buffer[BUTTON_IDX];
+ frame_seq_nb2 = rx_buffer[SEQUENCE_IDX];
+ tag_frequency = rx_buffer[NEARP_TAGFREQ_INDEX];
+ tag_slotpos = rx_buffer[NEARP_TAGSLOTPOS_INDEX];
+ ////////////////基站汇总模式数据
+ memcpy(&rec_tagheight,&rx_buffer[NEARBASEID_INDEX+rec_nearbase_num*6+4],2);
+ memcpy(&recnearbaselist_id,&rx_buffer[NEARBASEID_INDEX],rec_nearbase_num*2);
+ memcpy(&recnearbaselist_dist,&rx_buffer[NEARBASEID_INDEX+rec_nearbase_num*2],rec_nearbase_num*4+4);
+ usart_send[2] = 0x0c;//正常模式
+ usart_send[3] = 15+8*(rec_nearbase_num+1);//数据段长度
+ memcpy(&usart_send[4],&tag_id_recv,2);
+ usart_send[6] = rx_buffer[SEQUENCE_IDX];
+ usart_send[7] = rx_buffer[SEQUENCEH_IDX];
+ usart_send[8] = battary;
+ usart_send[9] = button;
+ memcpy(&usart_send[10],&rec_tagheight,2);
+ usart_send[12] = tag_frequency;
+ usart_send[13] = tag_slotpos;
+ usart_send[14] = 0;
+ usart_send[15] = 0;
+ usart_send[16] = rec_nearbase_num+1;
+ memcpy(&usart_send[17],&anc_id_recv,2);
+ memcpy(&usart_send[19],&recnearbaselist_id,2*rec_nearbase_num);
+ memcpy(&usart_send[19+rec_nearbase_num*2],&recnearbaselist_dist,4*rec_nearbase_num+4);
+
+ checksum = Checksum_u16(&usart_send[2],23+8*rec_nearbase_num);
+ memcpy(&usart_send[25+8*rec_nearbase_num],&checksum,2);
+ UART_PushFrame(usart_send,27+8*rec_nearbase_num);
+
+ //////////////////////////////////////////////////////////////
+
+
+GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_SET);
+ if(anc_id_recv==dev_id)
+ {
+ Anchor_RecNearPoll(rec_nearbase_num);
+ }else{
+
+ for(i=0;i<rec_nearbase_num;i++)
{
memcpy(&tempid,&rx_buffer[NEARBASEID_INDEX+i*2],2);
if(tempid==dev_id)
- Anchor_RecNearPoll(i+1);
+ {
+
+ seize_anchor=0; //非抢占。已存在列表中
+ Anchor_RecNearPoll(i);
+ break;
+ }
}
- }
+ }
+ //抢占模式
+// if(i==rec_nearbase_num)
+// {
+// seize_anchor=1; //抢占anchor
+// Anchor_RecNearPoll(i);
+// }
+// if(tag_id_recv==0x4008)
+// printf("标签高度: %d,基站高度: %d,高度差： %d. \r\n",rec_tagheight,intheight,intheight-rec_tagheight);
+
break;
-
- }
-
- }
- else
- {
+ default:
+
+ break;
+ }
+ }else{
+ #ifdef DEBUG_INF
+ printf("poll包失败：%x/n",status_reg);
+ #endif
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
--
Gitblit v1.9.3