From 942d685e55e3a58b6bcd7d0158765e9648b9373a Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期四, 28 十月 2021 22:16:01 +0800
Subject: [PATCH] 中断模式，配合时间片测试完成
---
源码/核心板/Src/application/dw_app.c | 55 +++++++++++++++++++++++++++++++++++++++----------------
1 files changed, 39 insertions(+), 16 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index c34e398..a75e8ea 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -7,7 +7,7 @@
NEARPOLL,
}tag_state=GETNEARMSG;
static dwt_config_t config = {
- 2, /* Channel number. */
+ 5, /* Channel number. */
DWT_PRF_64M, /* Pulse repetition frequency. */
DWT_PLEN_64, /* Preamble length. */
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
@@ -129,7 +129,7 @@
/* Configure DW1000. See NOTE 6 below. */
dwt_configure(&config);//配置DW1000
-
+dwt_setinterrupt( DWT_INT_RFCG | (DWT_INT_ARFE | DWT_INT_RFSL | DWT_INT_SFDT | DWT_INT_RPHE | DWT_INT_RFCE | DWT_INT_RFTO | DWT_INT_RXPTO), 1);
/* Apply default antenna delay value. See NOTE 1 below. */
dwt_setrxantennadelay(RX_ANT_DLY); //设置接收天线延迟
@@ -1061,7 +1061,7 @@
poll_rx_ts_32 = (uint32_t)poll_rx_ts;//使用32位数据计算
resp_tx_ts_32 = (uint32_t)resp_tx_ts;
final_rx_ts_32 = (uint32_t)final_rx_ts;
- time_monitor[1] = sync_timer*1000+TIM3->CNT;
+// time_monitor[1] = sync_timer*1000+TIM3->CNT;
Ra = (double)(resp_rx_ts - poll_tx_ts);//Tround1 = T4 - T1
Rb = (double)(final_rx_ts_32 - resp_tx_ts_32);//Tround2 = T6 - T3
Da = (double)(final_tx_ts - resp_rx_ts);//Treply2 = T5 - T4
@@ -1071,13 +1071,13 @@
distance = tof * SPEED_OF_LIGHT;//距离=光速*飞行时间
dist_no_bias = distance - dwt_getrangebias(config.chan, (float)distance, config.prf); //距离减去矫正系数
dist_cm = dist_no_bias * 100; //dis 为单位为cm的距离
- dwt_readdiagnostics(&d1);
+ // dwt_readdiagnostics(&d1);
// time_monitor[2] = sync_timer*1000+TIM3->CNT;
- LOS(&d1);
- time_monitor[3] = sync_timer*1000+TIM3->CNT;
+ // LOS(&d1);
+ // time_monitor[3] = sync_timer*1000+TIM3->CNT;
/*--------------------------以下为非测距逻辑------------------------*/
//dist_cm=33000;
- GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_RESET);
+ //GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_RESET);
LED0_BLINK; //每成功一次通讯则闪烁一次
dis_after_filter=dist_cm;
hex_dist = dist_cm+(int16_t)g_com_map[DIST_OFFSET];
@@ -1141,6 +1141,18 @@
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
+void Anchor_Start(void)
+{
+dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
+ g_start_sync_flag=0;
+
+ dwt_setrxtimeout(1000);//设定接收超时时间，0位没有超时时间
+ dwt_rxenable(0);//打开接收
+// while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
+// {
+// //IdleTask();
+// };
+}
extern int32_t intheight;
extern u16 synclost_count;
uint32_t current_syncid=0xffffffff,synclost_timer;
@@ -1150,6 +1162,7 @@
u16 recnearbaselist_id[30],rec_taganc_signalpower_list[11];
int32_t recnearbaselist_dist[30];
int16_t rec_tagheight;
+u16 timm = 0;
void Anchor_App(void)
{
@@ -1157,21 +1170,23 @@
u16 tempid;
uint32_t rec_syncid;
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
- g_start_sync_flag=0;
+// dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
+// g_start_sync_flag=0;
- dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
- dwt_rxenable(0);//打开接收
+// dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
+// dwt_rxenable(0);//打开接收
// GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
- {
- IdleTask();
- };
+// while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到接收成功或者出现错误
+// {
+// //IdleTask();
+// };
//GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_RESET);
+ dwt_setinterrupt( DWT_INT_RFCG | (DWT_INT_ARFE | DWT_INT_RFSL | DWT_INT_SFDT | DWT_INT_RPHE | DWT_INT_RFCE | DWT_INT_RFTO | DWT_INT_RXPTO), 0);
+ status_reg = dwt_read32bitreg(SYS_STATUS_ID);
if (status_reg & SYS_STATUS_RXFCG)//成功接收
{ u16 tag_recv_interval;
float temp_tagpos;
- time_monitor[0] = sync_timer*1000+TIM3->CNT;
+// time_monitor[0] = sync_timer*1000+TIM3->CNT;
g_Resttimer=0;
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG);//清除标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFL_MASK_1023;//获得接收数据长度
@@ -1394,6 +1409,9 @@
checksum = Checksum_u16(&usart_send[2],23+8*rec_nearbase_num);
memcpy(&usart_send[25+8*rec_nearbase_num],&checksum,2);
UART_PushFrame(usart_send,27+8*rec_nearbase_num);
+// UART_CheckSend();
+
+ timm++;
}
//////////////////////////////////////////////////////////////
@@ -1436,5 +1454,10 @@
#endif
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
+UART_CheckSend();
+ dwt_setinterrupt( DWT_INT_RFCG | (DWT_INT_ARFE | DWT_INT_RFSL | DWT_INT_SFDT | DWT_INT_RPHE | DWT_INT_RFCE | DWT_INT_RFTO | DWT_INT_RXPTO), 1);
+ dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
+ dwt_rxenable(0);//打开接收
+
}
--
Gitblit v1.9.3