From c20b80fe9dfe72220649bf1d85550e9f3ebc9549 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期日, 05 九月 2021 20:27:46 +0800
Subject: [PATCH] 增加中断接收模式，未测试。
---
源码/核心板/Src/application/dw_app.c | 49 +++++++++++++++++++++++++++++++++++--------------
1 files changed, 35 insertions(+), 14 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index dc17da9..6a49fef 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -130,7 +130,7 @@
dwt_configure(&config);//配置DW1000
-
+ dwt_setinterrupt(DWT_INT_TFRS | DWT_INT_RFCG | (DWT_INT_ARFE | DWT_INT_RFSL | DWT_INT_SFDT | DWT_INT_RPHE | DWT_INT_RFCE | DWT_INT_RFTO | DWT_INT_RXPTO), 1);
/* Apply default antenna delay value. See NOTE 1 below. */
dwt_setrxantennadelay(RX_ANT_DLY); //设置接收天线延迟
dwt_settxantennadelay(TX_ANT_DLY); //设置发射天线延迟
@@ -1059,7 +1059,7 @@
poll_rx_ts_32 = (uint32_t)poll_rx_ts;//使用32位数据计算
resp_tx_ts_32 = (uint32_t)resp_tx_ts;
final_rx_ts_32 = (uint32_t)final_rx_ts;
- time_monitor[1] = sync_timer*1000+TIM3->CNT;
+// time_monitor[1] = sync_timer*1000+TIM3->CNT;
Ra = (double)(resp_rx_ts - poll_tx_ts);//Tround1 = T4 - T1
Rb = (double)(final_rx_ts_32 - resp_tx_ts_32);//Tround2 = T6 - T3
Da = (double)(final_tx_ts - resp_rx_ts);//Treply2 = T5 - T4
@@ -1072,7 +1072,7 @@
dwt_readdiagnostics(&d1);
// time_monitor[2] = sync_timer*1000+TIM3->CNT;
LOS(&d1);
- time_monitor[3] = sync_timer*1000+TIM3->CNT;
+// time_monitor[3] = sync_timer*1000+TIM3->CNT;
/*--------------------------以下为非测距逻辑------------------------*/
//dist_cm=33000;
GPIO_WriteBit(GPIOB, GPIO_Pin_10, Bit_RESET);
@@ -1147,6 +1147,18 @@
u16 recnearbaselist_id[30];
int32_t recnearbaselist_dist[30];
int16_t rec_tagheight;
+void Anchor_Start(void)
+{
+dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
+ g_start_sync_flag=0;
+
+ dwt_setrxtimeout(1000);//设定接收超时时间，0位没有超时时间
+ dwt_rxenable(0);//打开接收
+// while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
+// {
+// //IdleTask();
+// };
+}
void Anchor_App(void)
{
@@ -1154,21 +1166,22 @@
u16 tempid;
uint32_t rec_syncid;
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
- g_start_sync_flag=0;
+// dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
+// g_start_sync_flag=0;
- dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
- dwt_rxenable(0);//打开接收
-// GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
- {
- IdleTask();
- };
+// dwt_setrxtimeout(0);//设定接收超时时间，0位没有超时时间
+// dwt_rxenable(0);//打开接收
+//// GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
+// while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
+// {
+// IdleTask();
+// };
+ status_reg = dwt_read32bitreg(SYS_STATUS_ID);
//GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_RESET);
if (status_reg & SYS_STATUS_RXFCG)//成功接收
{ u16 tag_recv_interval;
float temp_tagpos;
- time_monitor[0] = sync_timer*1000+TIM3->CNT;
+ //time_monitor[0] = sync_timer*1000+TIM3->CNT;
g_Resttimer=0;
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG);//清除标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFL_MASK_1023;//获得接收数据长度
@@ -1196,6 +1209,10 @@
tagofflinetime[taglist_pos]=0;
rec_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ if(rec_nearbase_num>=30)
+ {
+ break;
+ }
battary = rx_buffer[BATTARY_IDX];
button = rx_buffer[BUTTON_IDX];
frame_seq_nb2 = rx_buffer[SEQUENCE_IDX];
@@ -1316,6 +1333,10 @@
temp_tagpos=round((float)(sync_timer%g_com_map[COM_INTERVAL])/slottime);
tagpos_rec[(u8)temp_tagpos]=1;
rec_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ if(rec_nearbase_num>30)
+ {
+ break;
+ }
battary = rx_buffer[BATTARY_IDX];
button = rx_buffer[BUTTON_IDX];
frame_seq_nb2 = rx_buffer[SEQUENCE_IDX];
@@ -1345,7 +1366,7 @@
checksum = Checksum_u16(&usart_send[2],23+8*rec_nearbase_num);
memcpy(&usart_send[25+8*rec_nearbase_num],&checksum,2);
- // UART_PushFrame(usart_send,27+8*rec_nearbase_num);
+ UART_PushFrame(usart_send,27+8*rec_nearbase_num);
//////////////////////////////////////////////////////////////
--
Gitblit v1.9.3