From dd7cafaa933d27a9cabcf071147cb8ad09b49c62 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期四, 20 五月 2021 10:23:47 +0800
Subject: [PATCH] V1.50 增加小组功能
---
源码/核心板/Src/application/dw_app.c | 175 +++++++++++++++++++++++++++++++++++++++++++--------------
1 files changed, 131 insertions(+), 44 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index 157564f..c98ce3b 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -1,11 +1,12 @@
#include "dw_app.h"
#include "ADC.h"
+#define TDFILTER
enum enumtagstate
{
DISCPOLL,
GETNEARMSG,
NEARPOLL,
-}tag_state=GETNEARMSG;
+}tag_state=NEARPOLL;
static dwt_config_t config = {
2, /* Channel number. */
DWT_PRF_64M, /* Pulse repetition frequency. */
@@ -13,7 +14,7 @@
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
9, /* TX preamble code. Used in TX only. */
9, /* RX preamble code. Used in RX only. */
- 0, /* Use non-standard SFD (Boolean) */
+ 1, /* Use non-standard SFD (Boolean) */
DWT_BR_6M8, /* Data rate. */
DWT_PHRMODE_STD, /* PHY header mode. */
(129 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
@@ -28,7 +29,7 @@
static uint8_t tx_near_msg[80] = {0};
-static uint32_t frame_seq_nb = 0;
+ uint32_t frame_seq_nb = 0, frame_seq_nb2 = 0;
static uint32_t status_reg = 0;
static uint8_t rx_buffer[100];
static uint64_t poll_tx_ts;
@@ -136,6 +137,7 @@
* As this example only handles one incoming frame with always the same delay and timeout, those values can be set here once for all. */
//设置接收超时时间
}
+extern u16 group_id;
void Dw1000_App_Init(void)
{
//g_com_map[DEV_ID] = 0x0b;
@@ -144,6 +146,10 @@
tx_final_msg[MESSAGE_TYPE_IDX]=FINAL;
tx_sync_msg[MESSAGE_TYPE_IDX]=SYNC;
+ memcpy(&tx_poll_msg[GROUP_ID_IDX], &group_id, 1);
+ memcpy(&tx_final_msg[GROUP_ID_IDX], &group_id, 1);
+ memcpy(&tx_resp_msg[GROUP_ID_IDX], &group_id, 1);
+
memcpy(&tx_poll_msg[TAG_ID_IDX], &dev_id, 2);
memcpy(&tx_final_msg[TAG_ID_IDX], &dev_id, 2);
memcpy(&tx_resp_msg[ANCHOR_ID_IDX], &dev_id, 2);
@@ -332,22 +338,30 @@
last_nearbase_num=next_nearbase_num;
nearbase_num=next_nearbase_num;
recbase_num=0;
+ tx_nearpoll_msg[GROUP_ID_IDX] = group_id;
tx_nearpoll_msg[BATTARY_IDX] = Get_Battary();
tx_nearpoll_msg[BUTTON_IDX] = !READ_KEY0;
tx_nearpoll_msg[SEQUENCE_IDX] = frame_seq_nb++;
tx_nearpoll_msg[NEARBASENUM_INDEX] = nearbase_num;
memcpy(&tx_nearpoll_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
+ for(i=0;i<nearbase_num;i++)
+ { memcpy(&tx_nearpoll_msg[NEARBASEID_INDEX+nearbase_num*2+i*2],&nearbase_distlist[i],2);}
+
+ for(i=0;i<MAX_NEARBASE_NUM;i++)
+ {
+ nearbase_distlist[i]=0x1ffff;
+ }
tx_nearpoll_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
memcpy(&tx_nearpoll_msg[ANCHOR_ID_IDX],&mainbase_id,2);
- dwt_writetxdata(13+2*nearbase_num, tx_nearpoll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
+ dwt_writetxdata(13+4*nearbase_num, tx_nearpoll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(13+4*nearbase_num, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
flag_finalsend=0;
flag_rxon=1;
neartimout_timer=0;
get_newbase=0;
- timeout=ceil((float)nearbase_num*0.4)+3;
+ timeout=ceil((float)nearbase_num*SLOT_SCALE)+3;
//timeout=5;
mainbase_dist=100000;
mainbase_lost_count++;
@@ -443,10 +457,38 @@
final_msg_set_ts(&tx_nearfinal_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
final_msg_set_ts(&tx_nearfinal_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
tx_nearfinal_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
+ tx_nearfinal_msg[GROUP_ID_IDX] = group_id;
dwt_writetxdata(28+nearbase_num*4, tx_nearfinal_msg, 0);//将发送数据写入DW1000
dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
-
+ if(temp_dist!=0x1ffff)
+ {
+ g_Resttimer=0;
+ IWDG_Feed();
+ #ifdef USART_SINGLE_OUTPUT
+ usart_send[2] = 1;//正常模式
+ usart_send[3] = 17;//数据段长度
+ usart_send[4] = frame_seq_nb;//数据段长度
+ if(g_com_map[DEV_ROLE])
+ {
+ memcpy(&usart_send[5],&dev_id,2);
+ memcpy(&usart_send[7],&rec_nearbaseid,2);
+ }else{
+ memcpy(&usart_send[5],&rec_nearbaseid,2);
+ memcpy(&usart_send[7],&dev_id,2);
+ }
+ memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
+ usart_send[13] = battary;
+ usart_send[14] = button;
+ checksum = Checksum_u16(&usart_send[2],17);
+ memcpy(&usart_send[19],&checksum,2);
+ UART_PushFrame(usart_send,21);
+ #endif
+
+ //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+ // result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
+ }
}else{
@@ -473,18 +515,24 @@
// tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
if(temp_dist!=0x1ffff)
{
- #ifndef USART_INTEGRATE_OUTPUT
+ #ifdef USART_SINGLE_OUTPUT
usart_send[2] = 1;//正常模式
usart_send[3] = 17;//数据段长度
usart_send[4] = frame_seq_nb;//数据段长度
+ if(g_com_map[DEV_ROLE])
+ {
memcpy(&usart_send[5],&dev_id,2);
- memcpy(&usart_send[7],&rec_nearbaseid,2);
+ memcpy(&usart_send[7],&rec_nearbaseid,2);
+ }else{
+ memcpy(&usart_send[5],&rec_nearbaseid,2);
+ memcpy(&usart_send[7],&dev_id,2);
+ }
memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
usart_send[13] = battary;
usart_send[14] = button;
checksum = Checksum_u16(&usart_send[2],17);
memcpy(&usart_send[19],&checksum,2);
- // UART_PushFrame(usart_send,21);
+ UART_PushFrame(usart_send,21);
#endif
//dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
@@ -522,7 +570,7 @@
// }
tagslotpos=GetRandomSlotPos(rec_tagpos_binary|tagpos_binary);
tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- tag_state=GETNEARMSG;
+ tag_state=NEARPOLL;
}
// tyncpoll_time=0;
next_nearbase_num=0;
@@ -574,19 +622,16 @@
report_num++;
}
}
- for(i=0;i<MAX_NEARBASE_NUM;i++)
- {
- nearbase_distlist[i]=0x1ffff;
- }
+
// printf("%d,%d",temp_sync_timer2,temp_sync_timer1);
-// #ifdef USART_INTEGRATE_OUTPUT
-// usart_send[2] = 4;//正常模式
-// usart_send[3] = report_num*6+2;//正常模式
-// checksum = Checksum_u16(&usart_send[2],report_num*6+2);
-// memcpy(&usart_send[4+report_num*6],&checksum,2);
-// UART_PushFrame(usart_send,6+report_num*6);
-// #endif
+ #ifdef USART_INTEGRATE_OUTPUT
+ usart_send[2] = 4;//正常模式
+ usart_send[3] = report_num*6+2;//正常模式
+ checksum = Checksum_u16(&usart_send[2],report_num*6+2);
+ memcpy(&usart_send[4+report_num*6],&checksum,2);
+ UART_PushFrame(usart_send,6+report_num*6);
+ #endif
// if(mainbase_lost_count>5)
// {
// //tag_state=DISCPOLL;
@@ -655,13 +700,19 @@
tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
}
+ #ifdef USART_INTEGRATE_OUTPUT
+ usart_send[2] = 4;//正常模式
+ usart_send[3] = report_num*6+2;//正常模式
+ checksum = Checksum_u16(&usart_send[2],report_num*6+2);
+ memcpy(&usart_send[4+report_num*6],&checksum,2);
+ UART_PushFrame(usart_send,6+report_num*6);
+ #endif
}
void Tag_App(void)//发送模式(TAG标签)
{
//LED0_ON;
dwt_forcetrxoff();
- g_Resttimer=0;
GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
switch(tag_state)
{
@@ -735,7 +786,7 @@
battary = rx_buffer[BATTARY_IDX];
button = rx_buffer[BUTTON_IDX];
- frame_seq_nb = rx_buffer[SEQUENCE_IDX];
+ frame_seq_nb2 = rx_buffer[SEQUENCE_IDX];
if(result==0)
{
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))///不断查询芯片状态直到接收成功或者出现错误
@@ -785,7 +836,8 @@
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
}
}
-u8 misdist_num[TAG_NUM_IN_SYS],seize_anchor;
+extern u16 dist_threshold;
+u8 misdist_num[TAG_NUM_IN_SYS],seize_anchor,getrange_success=0;
u8 Anchor_RecNearPoll(u8 ancrec_nearbasepos) //0 mainbase 1 first near_base
{
u8 motorstate;
@@ -835,9 +887,7 @@
}
result = dwt_starttx(DWT_START_TX_DELAYED | DWT_RESPONSE_EXPECTED);//延迟发送，等待接收
- battary = rx_buffer[BATTARY_IDX];
- button = rx_buffer[BUTTON_IDX];
- frame_seq_nb = rx_buffer[SEQUENCE_IDX];
+
if(result==0)
{
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_sync_flag)///不断查询芯片状态直到接收成功或者出现错误
@@ -856,7 +906,7 @@
{
return 1;
}
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_FINAL&&!memcmp(&rx_buffer[TAG_ID_IDX],&tag_id_recv,2)) //判断是否为Final包
+ if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_FINAL&&!memcmp(&rx_buffer[TAG_ID_IDX],&tag_id_recv,2)&&group_id==rx_buffer[GROUP_ID_IDX]) //判断是否为Final包
{
uint32_t poll_tx_ts, resp_rx_ts, final_tx_ts;
uint32_t poll_rx_ts_32, resp_tx_ts_32, final_rx_ts_32;
@@ -879,28 +929,40 @@
tof = tof_dtu * DWT_TIME_UNITS;
distance = tof * SPEED_OF_LIGHT;//距离=光速*飞行时间
dist_no_bias = distance - dwt_getrangebias(config.chan, (float)distance, config.prf); //距离减去矫正系数
- dist_cm = dist_no_bias * 100; //dis 为单位为cm的距离
+ dist_cm = dist_no_bias * 1000; //dis 为单位为cm的距离
/*--------------------------以下为非测距逻辑------------------------*/
//dist_cm=33000;
+ getrange_success = 1;
LED0_BLINK; //每成功一次通讯则闪烁一次
dis_after_filter=dist_cm;
- hex_dist = dist_cm+(int16_t)g_com_map[DIST_OFFSET];
+ hex_dist = dist_cm+(int16_t)g_com_map[DIST_OFFSET]*10;
g_flag_Taggetdist[taglist_pos]=0;
- if(hex_dist>-1000&&hex_dist<100000)
+ if(hex_dist>-1000&&hex_dist<2000000)
{
- if(abs(hex_dist-his_dist[taglist_pos])<1500||misdist_num[taglist_pos]>3)
+ if(abs(hex_dist-his_dist[taglist_pos])<dist_threshold||misdist_num[taglist_pos]>3)
{
+ int32_t filter_dist;
+ g_Resttimer=0;
+ IWDG_Feed();
+ #ifdef TDFILTER
+ NewTrackingDiffUpdate(taglist_pos, (float)hex_dist);
+ filter_dist=pos_predict[taglist_pos]/10;
+ #else
+ filter_dist=hex_dist/10;
+ #endif
misdist_num[taglist_pos]=0;
- tagdist_list[taglist_pos] = hex_dist;
+ tagdist_list[taglist_pos] = filter_dist;
his_dist[taglist_pos]=hex_dist;
- g_Tagdist[taglist_pos]=hex_dist;
- #ifndef USART_INTEGRATE_OUTPUT
+ g_Tagdist[taglist_pos]=filter_dist;
+ #ifdef USART_SINGLE_OUTPUT
usart_send[2] = 1;//正常模式
usart_send[3] = 17;//数据段长度
- usart_send[4] = frame_seq_nb;//数据段长度
+ usart_send[4] = frame_seq_nb2;//数据段长度
memcpy(&usart_send[5],&tag_id_recv,2);
- memcpy(&usart_send[7],&dev_id,2);
+ memcpy(&usart_send[7],&dev_id,2);
+ if(tagdist_list[taglist_pos]<=0)
+ tagdist_list[taglist_pos]=10;
memcpy(&usart_send[9],&tagdist_list[taglist_pos],4);
usart_send[13] = battary;
usart_send[14] = button;
@@ -926,7 +988,7 @@
uint32_t current_syncid=0xffffffff,synclost_timer;
extern u8 flag_syncbase;
u8 tagpos_rec[50],tagpos_send[50],ancidlist_num;
-u16 ancidlist_rec[20],ancidlist_send[20];
+u16 ancidlist_rec[20],ancidlist_send[20],rec_ancidlist[20],rec_ancdistlist[20];
void Anchor_App(void)
{
@@ -942,6 +1004,7 @@
// GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR))&&!g_start_send_flag&&!g_start_sync_flag)//不断查询芯片状态直到接收成功或者出现错误
{
+
IdleTask();
};
//GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_RESET);
@@ -949,7 +1012,7 @@
{ u16 tag_recv_interval;
float temp_tagpos;
- g_Resttimer=0;
+
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG);//清除标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFL_MASK_1023;//获得接收数据长度
dwt_readrxdata(rx_buffer, frame_len, 0);//读取接收数据
@@ -962,7 +1025,7 @@
// if (anchor_type == rx_buffer[ANC_TYPE_IDX])
// Anchor_RecPoll();
// break;
- case SYNC:
+ case SYNC:
memcpy(&rec_syncid,&rx_buffer[ANCHOR_ID_IDX],4);
if(rec_syncid<current_syncid)
{
@@ -1003,8 +1066,32 @@
}
break;
- case NEAR_POLL:
+ case NEAR_POLL:
+ frame_seq_nb2 = rx_buffer[SEQUENCE_IDX];
+ battary = rx_buffer[BATTARY_IDX];
+ button = rx_buffer[BUTTON_IDX];
+ rec_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
memcpy(&tag_id_recv,&rx_buffer[TAG_ID_IDX],2);
+ memcpy(&rec_ancidlist,&rx_buffer[NEARBASEID_INDEX],2*rec_nearbase_num);
+ memcpy(&rec_ancdistlist,&rx_buffer[NEARBASEID_INDEX+2*rec_nearbase_num],2*rec_nearbase_num);
+ #ifdef USART_ALL_OUTPUT
+ usart_send[2] = 0x0c;//正常模式
+ usart_send[3] = 8+rec_nearbase_num*4;//数据段长度
+ usart_send[4] = frame_seq_nb2;//数据段长度
+ usart_send[5] = battary;
+ usart_send[6] = button;
+ usart_send[7] = rec_nearbase_num;
+ memcpy(&usart_send[8],&tag_id_recv,2);
+ memcpy(&usart_send[10],&rec_ancidlist,2*rec_nearbase_num);
+ memcpy(&usart_send[10+rec_nearbase_num*2],&rec_ancdistlist,2*rec_nearbase_num);
+ checksum = Checksum_u16(&usart_send[2],8+4*rec_nearbase_num);
+ memcpy(&usart_send[10+4*rec_nearbase_num],&checksum,2);
+ UART_PushFrame(usart_send,12+rec_nearbase_num*4);
+ #endif
+ if(tag_id_recv>=g_com_map[WHITELIST1_START]&&tag_id_recv<=g_com_map[WHITELIST1_END])
+ {break;}
+ if(group_id!=rx_buffer[GROUP_ID_IDX])
+ {break;}
taglist_pos=CmpTagInList(tag_id_recv);
if(taglist_pos==taglist_num)
{
@@ -1016,9 +1103,9 @@
new_tagid=0;
}
tagofflinetime[taglist_pos]=0;
- temp_tagpos=round((float)(sync_timer%g_com_map[COM_INTERVAL])/slottime);
+ temp_tagpos=round((float)(sync_timer%g_com_map[COM_INTERVAL])/slottime);
tagpos_rec[(u8)temp_tagpos]=1;
- rec_nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+
if(rec_nearbase_num>ancidlist_num)
{
--
Gitblit v1.9.3