From eed71b230e2dae7fa190a84f7a60cb83646674f6 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期二, 21 四月 2020 22:34:50 +0800
Subject: [PATCH] v1.22 增加芯片电量显示
---
源码/核心板/Src/application/dw_app.c | 22 +++++++++++++++-------
1 files changed, 15 insertions(+), 7 deletions(-)
diff --git "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c" "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
index 9c6998d..3d4a60d 100644
--- "a/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
+++ "b/\346\272\220\347\240\201/\346\240\270\345\277\203\346\235\277/Src/application/dw_app.c"
@@ -240,7 +240,7 @@
for(i=0;i<255;i++)
{
g_flag_Taggetdist[i]++;
- if(g_flag_Taggetdist[i]>=20)
+ if(g_flag_Taggetdist[i]>=2)
{
g_Tagdist[i]=0xffff;
}
@@ -326,19 +326,24 @@
int8_t tag_delaytime;
extern uint16_t sync_timer;
u16 tmp_time;
+extern float dw_vbat;
void Tag_App(void)//发送模式(TAG标签)
{
uint32_t frame_len;
uint32_t final_tx_time;
u32 start_poll;
u8 i,getsync_flag=0;
+ u8 bat_percent;
//LED0_ON;
dwt_forcetrxoff();
g_Resttimer=0;
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
tag_succ_times = 0;
- tx_poll_msg[BATTARY_IDX] = Get_Battary();
+ bat_percent=(dw_vbat-2.8)/0.5*100;
+ if(bat_percent>100)
+ bat_percent=100;
+ tx_poll_msg[BATTARY_IDX] = bat_percent;//Get_Battary();
tx_poll_msg[BUTTON_IDX] = !READ_KEY0;
tx_poll_msg[SEQUENCE_IDX] = frame_seq_nb++;
GPIO_WriteBit(GPIOA, GPIO_Pin_9, Bit_RESET);
@@ -437,12 +442,14 @@
LED0_BLINK;
memcpy(&anc_id_recv,&rx_buffer[ANCHOR_ID_IDX],2);
-// g_Tagdist[anc_id_recv]= hex_dist;
-// g_flag_Taggetdist[anc_id_recv]=0;
+ if(hex_dist2!=0xffff)
+ {
+ g_Tagdist[anc_id_recv]= hex_dist2;
+ g_flag_Taggetdist[anc_id_recv]=0;
- if(!g_com_map[MODBUS_MODE]&&hex_dist2!=0xffff)
+ if(!g_com_map[MODBUS_MODE])
{
- hex_dist2 = hex_dist2+(int16_t)g_com_map[DIST_OFFSET];
+ hex_dist2 = hex_dist2;
usart_send[2] = 1;//正常模式
usart_send[3] = 17;//数据段长度
usart_send[4] = frame_seq_nb;//数据段长度
@@ -450,12 +457,13 @@
memcpy(&usart_send[7],&rx_buffer[ANCHOR_ID_IDX],2);
memcpy(&usart_send[9],&hex_dist2,4);
- usart_send[13] = battary;
+ usart_send[13] = bat_percent;
usart_send[14] = button;
checksum = Checksum_u16(&usart_send[2],17);
memcpy(&usart_send[19],&checksum,2);
UART_PushFrame(usart_send,21);
}
+ }
// memcpy(&Modbus_HoldReg[anc_id_recv*2],&hex_dist,4);
/* Poll DW1000 until TX frame sent event set. See NOTE 8 below. */
if(result==0)
--
Gitblit v1.9.3