From b27f5e9cc596aecba798b4a949479a8e775426d3 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期六, 11 六月 2022 16:01:33 +0800
Subject: [PATCH] 1
---
Src/application/dw_app.c | 166 +++++++++++++++++++++---------------------------------
1 files changed, 65 insertions(+), 101 deletions(-)
diff --git a/Src/application/dw_app.c b/Src/application/dw_app.c
index 304200c..dad20e6 100644
--- a/Src/application/dw_app.c
+++ b/Src/application/dw_app.c
@@ -30,6 +30,7 @@
#include "beep.h"
#include "modbus.h"
+//#define USART_INTEGRATE_OUTPUT
/*------------------------------------ Marcos ------------------------------------------*/
/* Inter-ranging delay period, in milliseconds. */
#define RNG_DELAY_MS 100
@@ -54,7 +55,7 @@
#define DELAY_BETWEEN_TWO_FRAME_UUS 400
-#define POLL_RX_TO_RESP_TX_DLY_UUS 420
+#define POLL_RX_TO_RESP_TX_DLY_UUS 470
/* This is the delay from the end of the frame transmission to the enable of the receiver, as programmed for the DW1000's wait for response feature. */
#define RESP_TX_TO_FINAL_RX_DLY_UUS 200
/* Receive final timeout. See NOTE 5 below. */
@@ -83,7 +84,7 @@
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
9, /* TX preamble code. Used in TX only. */
9, /* RX preamble code. Used in RX only. */
- 0, /* Use non-standard SFD (Boolean) */
+ 1, /* Use non-standard SFD (Boolean) */
DWT_BR_6M8, /* Data rate. */
DWT_PHRMODE_STD, /* PHY header mode. */
(129 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
@@ -92,7 +93,7 @@
static uint8_t tx_sync_msg[14] = {0};
static uint8_t tx_final_msg[60] = {0};
static uint8_t tx_resp_msg[22] = {0};
-static uint8_t tx_near_msg[80] = {0};
+ uint8_t tx_near_msg[80] = {0};
static uint32_t frame_seq_nb = 0;
static uint32_t status_reg = 0;
@@ -291,10 +292,10 @@
u8 flag_finalsend,flag_getresponse,flag_rxon;
uint16_t current_count,start_count,end_count,lastsync_timer;
-u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum;
+u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum, para_update,para_len,stationary_flag=0;
u32 rec_tagpos_binary;
int16_t offset=2700;
-u8 motor_state,rec_remotepara_state,rec_remotepara[30];
+u8 motor_state,rec_remotepara_state,rec_remotepara[80],firstrec_flag;
void NearPoll(void)
{
@@ -315,10 +316,11 @@
last_nearbase_num=next_nearbase_num;
nearbase_num=next_nearbase_num;
recbase_num=0;
- motor_state=0;
-
+ firstrec_flag = 0;
+// motor_state=0;
+ tx_near_msg[GROUP_ID_IDX] = group_id;
tx_near_msg[BATTARY_IDX] = bat_percent;
- tx_near_msg[BUTTON_IDX] = !GET_USERKEY;
+ tx_near_msg[BUTTON_IDX] = !GET_USERKEY|stationary_flag<<1;
tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
@@ -328,12 +330,14 @@
dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+ tx_near_msg[TAGCONFIGSUCCESS_INDEX] =0;
+ para_update = 0;
flag_finalsend=0;
flag_rxon=1;
flag_getresponse=0;
start_count=HAL_LPTIM_ReadCounter(&hlptim1);
recbase_num=0;
- timeout=ceil((float)nearbase_num*0.4)+2;
+ timeout=ceil((float)nearbase_num*SLOT_SCALE)+3;
end_count=start_count+(timeout<<5);
if(end_count>=32768)
{end_count-=32768;}
@@ -350,10 +354,12 @@
dw_systime=dwt_readsystimestamphi32();
if(dw_systime>temp1&&dw_systime<temp2)
{
-
+ flag_finalsend=0;
dwt_forcetrxoff();
flag_rxon=0;
dwt_setdelayedtrxtime(final_tx_time);
+ dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
flag_finalsend=0;
break;
@@ -374,22 +380,26 @@
dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
dwt_rxenable(0);//打开接收
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&rx_buffer[GROUP_ID_IDX]==group_id) //判断接收到的数据是否是response数据
{ u16 rec_nearbaseid,rec_nearbasepos;
- poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
+
resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
recbase_num++;
memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
- if(last_nearbase_num==0)
- {
- get_newbase=1;
- nearbaseid_list[0]=rec_nearbaseid;
- nearbase_num=1;
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
- }
- if(rec_nearbaseid==nearbaseid_list[0])
- {
- //////////////////////////////////时间同步
+ if(!firstrec_flag)
+ {
+ flag_finalsend = 1;
+ firstrec_flag = 1;
+ poll_tx_ts = get_tx_timestamp_u64();
+ final_tx_time = (poll_tx_ts+65535364 + ((RESP_RX_TO_FINAL_TX_DLY_UUS+DELAY_BETWEEN_TWO_FRAME_UUS*12+500) * UUS_TO_DWT_TIME)) >> 8;
+ temp1=final_tx_time-((650*UUS_TO_DWT_TIME)>>8);
+ temp2=final_tx_time+((100*UUS_TO_DWT_TIME)>>8);
+ final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
+ tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
+ tx_near_msg[GROUP_ID_IDX] = group_id;
+ //////////////////////////////////时间同步
memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
current_count=HAL_LPTIM_ReadCounter(&hlptim1);
@@ -402,77 +412,28 @@
if(sync_timer>=1010)
{sync_timer=0;}
}
- // TIM3->CNT=tmp_time;
-// if(tagslotpos>max_slotpos)
-// tagslotpos=tagslotpos%(max_slotpos+1);
-// tyncpoll_time=(tagslotpos-1)*slottime;
- ////////////////////////////
- rec_nearbasepos=0;
- exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
- memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
- nearbase_distlist[rec_nearbasepos]=temp_dist;
- if((rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
- motor_state=rx_buffer[MOTORSTATE_INDEX]&0xf;
- rec_remotepara_state=rx_buffer[MOTORSTATE_INDEX]>>4;
-
- mainbase_lost_count=0;
- flag_finalsend=1;
- memcpy(&mainbase_dist,&rx_buffer[DIST_IDX],4);
- final_tx_time = (resp_rx_ts + ((RESP_RX_TO_FINAL_TX_DLY_UUS+DELAY_BETWEEN_TWO_FRAME_UUS*nearbase_num+500) * UUS_TO_DWT_TIME)) >> 8;
- temp1=final_tx_time-((850*UUS_TO_DWT_TIME)>>8);
- temp2=final_tx_time+((100*UUS_TO_DWT_TIME)>>8);
- // dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
- tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
- dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
- flag_getresponse=1;
- memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
-
-
- //时间同步
- ancsync_time=((sync_timer)*1000+tmp_time);
+ ancsync_time=((sync_timer)*1000+tmp_time);
last_slotnum=current_slotnum;
current_slotnum=((float)sync_timer/g_com_map[COM_INTERVAL])+1;
if(current_slotnum==last_slotnum-1)
{flag_getresponse=1;}
lastsync_timer=sync_timer;
offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
- SetNextPollTime(tyncpoll_time);
- if(rec_remotepara_state&&rec_remotepara_state!=g_com_map[REMOTEPARA_STATE])
+ SetNextPollTime(tyncpoll_time);
+ // dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+ }
+ if(rec_remotepara_state==1)
{
- g_com_map[REMOTEPARA_STATE]=rec_remotepara_state;
- memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],REMOTEPARA_LEN);
+ memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],REMOTEPARA_LEN);
memcpy(&g_com_map[COM_INTERVAL],&rec_remotepara[0],8);
memcpy(&g_com_map[POWER],&rec_remotepara[8],10);
- save_com_map_to_flash();
- delay_ms(100);
- NVIC_SystemReset();
-
- }
-
- // count_offset=sync_count-current_count-143;
- // current_slottimes=(ancsync_time-10000)/(g_com_map[COM_INTERVAL]*1000);
- // nextpoll_delaytime=tyncpoll_time*1000+g_com_map[COM_INTERVAL]*1000-((ancsync_time)%(g_com_map[COM_INTERVAL]*1000))-4300;
-// if(abs(ancsync_time-910000)<1000)
-// {
-// nextpoll_delaytime+=10000;
-// }
-// if(nextpoll_delaytime<2000)
-// {
-// nextpoll_delaytime+=g_com_map[COM_INTERVAL]*1000;
-// }
-// lastpoll_count= current_count+(nextpoll_delaytime)/LPTIMER_LSB;
-// if(lastpoll_count>LPTIMER_1S_COUNT)
-// lastpoll_count-=LPTIMER_1S_COUNT;
-// __HAL_LPTIM_COMPARE_SET(&hlptim1, lastpoll_count);
- /////////////////////////////////////////
-// dwt_setdelayedtrxtime(final_tx_time);
-// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- }else{
+ if(g_com_map[COM_INTERVAL]>0&&g_com_map[COM_INTERVAL]<1000&&g_com_map[POWER]<67&&g_com_map[POWER]>0)
+ {save_com_map_to_flash();
+ delay_ms(100);
+ }
+ NVIC_SystemReset();
+ }
+
rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
if(rec_nearbasepos>=last_nearbase_num) //发现新的基站
@@ -491,18 +452,9 @@
{
motor_state=rx_buffer[MOTORSTATE_INDEX];
}
-
final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
- dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
-
-
- //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- // result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
- }
- }
+ }
}else{
dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
if(flag_rxon)
@@ -511,9 +463,11 @@
}
// dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
}
-dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ if(mainbase_lost_count>tag_frequency*BASELOST_STOPMOTOR_TIME)
+ {motor_state=0; }
+ dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
nearbase_num=recbase_num;
- j=0;
+ j=0;
if(exsistbase_list[0]==0)
{
// u8 temp_adc,random_value;
@@ -570,18 +524,27 @@
{
nearbaseid_list[i]=true_nearbase_idlist[i];
nearbase_distlist[i]=true_nearbase_distlist[i];
- if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==0xa)
+ if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==KEEP_TIMES)
{
memcpy(&usart_send[4+6*report_num],&nearbaseid_list[i],2);
memcpy(&usart_send[6+6*report_num],&nearbase_distlist[i],4);
report_num++;
}
}
+ #ifdef USART_INTEGRATE_OUTPUT
+ usart_send[0] = 0x55;
+ usart_send[1] = 0xAA;
+ usart_send[2] = 4;//正常模式
+ usart_send[3] = report_num*6+2;//正常模式
+ checksum = Checksum_u16(&usart_send[2],report_num*6+2);
+ memcpy(&usart_send[4+report_num*6],&checksum,2);
+ USART_puts(usart_send,6+report_num*6);
+ #endif
+
for(i=0;i<MAX_NEARBASE_NUM;i++)
{
nearbase_distlist[i]=0x1ffff;
}
-
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
@@ -597,6 +560,7 @@
}
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&nearmsg_mainbase,2);
memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
+ tx_near_msg[GROUP_ID_IDX] = group_id;
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
@@ -633,10 +597,10 @@
tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
}
}
-
+u32 id;
void Tag_App(void)//发送模式(TAG标签)
{
- u32 id;
+
//LED0_ON;
id = dwt_readdevid() ;
while (DWT_DEVICE_ID != id)
@@ -662,5 +626,5 @@
//GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_RESET);
break;
}
-// dwt_entersleep();
+ dwt_entersleep();
}
--
Gitblit v1.9.3