From 027bc1bbfe61d1c28617340b7886586c38ac4eec Mon Sep 17 00:00:00 2001
From: WXK <287788329@qq.com>
Date: 星期二, 07 十一月 2023 09:17:58 +0800
Subject: [PATCH] lora免布线标签5hz版本 没有调试好 先提交 目前不用
---
Src/main.c | 529 ++++++++++++++++++++++++++++++----------------------------
1 files changed, 274 insertions(+), 255 deletions(-)
diff --git a/Src/main.c b/Src/main.c
index b151144..602e100 100644
--- a/Src/main.c
+++ b/Src/main.c
@@ -30,10 +30,15 @@
#include "TrackingDiff.h"
#include "dw_app.h"
#include "Flash.h"
+#include "user.h"
+#include "sx126x-board.h"
+#include "string.h"
+#include "stdio.h"
+#include "delay.h"
#define NSH1 0x0001
#define GP 0x0002
#define FLASH_HARDWARE_VERSION_MAP (uint32_t)0x08004F00 //硬件版本号和批次信息位置
-//#define DEBUG_MODE
+#define DEBUG_MODE
/* USER CODE END Includes */
/* Private typedef -----------------------------------------------------------*/
@@ -55,11 +60,11 @@
/* Private variables ---------------------------------------------------------*/
ADC_HandleTypeDef hadc;
+IWDG_HandleTypeDef hiwdg;
+
LPTIM_HandleTypeDef hlptim1;
SPI_HandleTypeDef hspi1;
-
-TIM_HandleTypeDef htim2;
UART_HandleTypeDef huart1;
DMA_HandleTypeDef hdma_usart1_rx;
@@ -77,7 +82,7 @@
static void MX_SPI1_Init(void);
void MX_ADC_Init(void);
static void MX_DMA_Init(void);
-static void MX_TIM2_Init(void);
+static void MX_IWDG_Init(void);
/* USER CODE BEGIN PFP */
/* USER CODE END PFP */
@@ -91,10 +96,15 @@
extern u8 motor_state;
uint16_t tyncpoll_time,lpsettime;
uint16_t slottime,max_slotpos;
-uint16_t lastpoll_count,interval_count,slot_startcount,tag_frequency,lastpoll_time,current_time;
+uint16_t lastpoll_count,interval_count,slot_startcount,tag_frequency,lastpoll_time;
extern uint8_t module_power;
extern float nomove_count;
uint8_t imu_enable,motor_enable;
+uint32_t lp_time;
+extern uint32_t lora_txtime_old;
+uint8_t lora_tx_flag;
+extern uint16_t Lora_tx_ancid[50];
+extern uint16_t Lora_tx_ancdist[50];
u16 GetLPTime(void)
{
u16 count=HAL_LPTIM_ReadCounter(&hlptim1);
@@ -110,11 +120,34 @@
Error_Handler();
}
}
+static void MX_DMA_DeInit(void)
+{
+
+ /* DMA controller clock enable */
+ __HAL_RCC_DMA1_CLK_DISABLE();
+
+ /* DMA interrupt init */
+ /* DMA1_Channel2_3_IRQn interrupt configuration */
+ // HAL_NVIC_SetPriority(DMA1_Channel2_3_IRQn, 1, 0);
+ HAL_NVIC_DisableIRQ(DMA1_Channel2_3_IRQn);
+
+}
+void UsartDeInit(void)
+{
+ GPIO_InitTypeDef GPIO_InitStruct = {0};
+ waitusart_timer = 0;
+ MX_DMA_DeInit();
+ HAL_UART_DeInit(&huart1);
+ GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
+ GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+}
uint16_t hardware_version,hardware_pici,hardware_type;
-uint8_t state5v;
+uint8_t state5v = 1;
float motor_keeptime;
void IdleTask(void)
-{u16 current_time;
+{
//if(huart1.Instance->ISR&USART_ISR_FE)
// {
// SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
@@ -133,21 +166,25 @@
}
if(bat_percent>99)
{
- LED_LR_OFF;
+// LED_LR_OFF;
LED_LG_ON;
}else{
- LED_LR_ON;
+// LED_LR_ON;
LED_LG_OFF;
}
}else{
- state5v=0;
- LED_LR_OFF;
+ if(state5v==1)
+ {
+ state5v=0;
+ UsartDeInit();
+ }
+// LED_LR_OFF;
LED_LG_OFF;
// }
}
- if(g_com_map[MAP_SIGN_INDEX]!=0x55AA||g_com_map[COM_INTERVAL]==0)
+ if(g_com_map[MAP_SIGN_INDEX]!=0x55AA||g_com_map[COM_INTERVAL]==0)
{
- SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
+ SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
}
}
@@ -174,7 +211,7 @@
// {
// lpcount+=LPTIMER_1S_COUNT;
// }
- lpcount = last_lpcount+32768/tag_frequency;
+ lpcount = last_lpcount+32768/tag_frequency-time*LPTIMER_LSB;
while(lpcount>LPTIMER_1S_COUNT)
{
lpcount-=LPTIMER_1S_COUNT;
@@ -182,30 +219,6 @@
last_lpcount = lpcount;
__HAL_LPTIM_COMPARE_SET(&hlptim1, lpcount);
-}
-
-void HardWareTypeDiffConfig(void)
-{
-GPIO_InitTypeDef GPIO_InitStruct = {0};
-//hardware_type=2;
-if(hardware_type == 0)
- hardware_type = 1;
- switch(hardware_type)
- {
- case 1:
-
- HAL_GPIO_WritePin(GPIOB, MOTOR_Pin, GPIO_PIN_SET);
- GPIO_InitStruct.Pin = MOTOR_Pin;
- GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
- GPIO_InitStruct.Pull = GPIO_NOPULL;
- GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
- HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
- break;
- case 2:
- MX_TIM2_Init();
- //BarInit();
- break;
- }
}
u8 active_flag,nomovesleeptime;
void Program_Init(void)
@@ -218,18 +231,20 @@
hardware_pici = STMFLASH_ReadHalfWord(FLASH_HARDWARE_VERSION_MAP+2);
hardware_type = STMFLASH_ReadHalfWord(FLASH_HARDWARE_VERSION_MAP+4);
//deca_sleep(1000);
- g_com_map[VERSION] = (1<<8)|52;
-
+ g_com_map[VERSION] = (1<<8)|68;
+// g_com_map[DEV_ID]=1158;
#ifdef DEBUG_MODE
-// g_com_map[GROUP_ID]=21;
+ // g_com_map[GROUP_ID]=21;
// g_com_map[DEV_ID]=4;
// g_com_map[COM_INTERVAL]=100;
// g_com_map[MAX_REPORT_ANC_NUM]=1;
// g_com_map[NOMOVESLEEP_TIME]=10;
#endif
-
+ g_com_map[GROUP_ID]=3;
+ g_com_map[COM_INTERVAL] = 200;
active_flag = g_com_map[ACTIVE_INDEX];
module_power = g_com_map[POWER];
+ g_com_map[IMU_ENABLE] = 0;
imu_enable=g_com_map[IMU_ENABLE];
motor_enable=g_com_map[MOTOR_ENABLE];
@@ -250,25 +265,25 @@
}
// g_com_map[COM_INTERVAL]=100;
- if(g_com_map[COM_INTERVAL]==0)
- {
- g_com_map[COM_INTERVAL]=100;
- }
+// if(g_com_map[COM_INTERVAL]==0)
+// {
+// g_com_map[COM_INTERVAL]=100;
+// }
if(module_power>67)
{module_power=67;}
if(module_power<0)
{module_power=0;}
current_slotnum=1;
- current_time=GetLPTime();
- if (HAL_LPTIM_TimeOut_Start_IT(&hlptim1, LPTIMER_1S_COUNT, slot_startcount) != HAL_OK) //system time is 1010ms 1 puls=30.518us
- {
- Error_Handler();
- }
+// current_time=GetLPTime();
+// g_com_map[COM_INTERVAL]=200;
+// if (HAL_LPTIM_TimeOut_Start_IT(&hlptim1, LPTIMER_1S_COUNT, (float)(32768/1000)*g_com_map[COM_INTERVAL]) != HAL_OK) //system time is 1010ms 1 puls=30.518us
+// {
+// Error_Handler();
+// }
+ HAL_LPTIM_TimeOut_Start_IT(&hlptim1, LPTIMER_1S_COUNT,32767);
//g_com_map[NOMOVESLEEP_TIME]=5;
- printf("标签ID: %d .\r\n",dev_id);
- printf("通讯间隔: %d ms.\r\n",g_com_map[COM_INTERVAL]);
- printf("单次通讯基站数量: %d个.\r\n",g_com_map[MAX_REPORT_ANC_NUM]);
+ printf("固件版本: 免布线基站 V%d.%d. \r\n",g_com_map[VERSION]>>8,g_com_map[VERSION]&0xff);
memcpy(g_com_map2,g_com_map,COM_MAP_SIZE);
// printf("DEVICE PAIRID: %d .\r\n",g_com_map[PAIR_ID]);
// printf("DEVICE ALARM DISTANCE: 1.%d 2.%d 3.%d .\r\n",g_com_map[ALARM_DISTANCE1],g_com_map[ALARM_DISTANCE2],g_com_map[ALARM_DISTANCE3]);
@@ -298,12 +313,6 @@
{
//SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
}
-/* USER CODE END 0 */
-
-/**
- * @brief The application entry point.
- * @retval int
- */
uint16_t temp2;
float dw_vbat,last_vbat;
uint8_t Get_Battary_UWB(void)
@@ -337,6 +346,85 @@
}
return last_value;
}
+void MX_ADC_DeInit(void)
+{
+ HAL_ADC_DeInit(&hadc);
+ HAL_ADCEx_DisableVREFINT();
+}
+uint16_t irq_num;
+void HAL_GPIO_EXTI_Callback(uint16_t GPIO_Pin)
+{
+ if(GPIO_Pin == GPIO_PIN_3)
+ {
+ SystemClock_Config();
+// l_bIsVibration = HIDO_TRUE;
+// nomove_time=0;
+// printf("RXD :77777\r\n");
+ irq_num++;
+ RadioIrqProcess();
+ }
+// if(GPIO_Pin == GPIO_PIN_8)
+// {
+// Anchor_App();
+// }
+}
+void Uwb_Lora_Switch(uint8_t uwb, uint8_t lora)
+{
+if(uwb)
+HAL_GPIO_WritePin(SPI_CS_GPIO_Port, SPI_CS_Pin, GPIO_PIN_SET);
+else
+HAL_GPIO_WritePin(SPI_CS_GPIO_Port, SPI_CS_Pin, GPIO_PIN_RESET);
+
+if(lora)
+HAL_GPIO_WritePin(GPIOB, RADIO_NSS_Pin, GPIO_PIN_SET);
+else
+HAL_GPIO_WritePin(GPIOB, RADIO_NSS_Pin, GPIO_PIN_RESET);
+}
+extern void Lora_tx_zubao( void );
+extern void Lora_tx_mode( void );
+extern uint8_t Lora_tx_ancnum;
+extern u8 lora_seq_nb2;
+extern uint16_t lora_yingda_num;
+uint16_t Lora_Txcount;
+uint16_t Old_Lora_Txcount;
+void Lora_Tx_Poll()
+{
+ if(lora_tx_flag)
+ {
+// HAL_GPIO_WritePin(GPIOA, GPIO_PIN_15, GPIO_PIN_SET);
+ lora_tx_flag=0;
+ LED_TB_ON;
+ lora_seq_nb2++;
+ Lora_tx_zubao();
+ Lora_tx_mode();
+ Radio.Send( usart_send, 12+Lora_tx_ancnum*4);
+ Lora_tx_ancnum=0;
+ memset(Lora_tx_ancdist,0,sizeof(Lora_tx_ancdist));
+ memset(Lora_tx_ancid,0,sizeof(Lora_tx_ancid));
+ }
+
+
+// Lora_Txcount=HAL_LPTIM_ReadCounter(&hlptim1);
+//
+// if(Lora_Txcount-Old_Lora_Txcount>=6554)
+// {
+// Old_Lora_Txcount=Lora_Txcount;
+// LED_TB_ON;
+// lora_seq_nb2++;
+// Lora_tx_zubao();
+// Lora_tx_mode();
+// Radio.Send( usart_send, 12+Lora_tx_ancnum*4);
+// Lora_tx_ancnum=0;
+// memset(Lora_tx_ancdist,0,sizeof(Lora_tx_ancdist));
+// memset(Lora_tx_ancid,0,sizeof(Lora_tx_ancid));
+// }
+}
+/* USER CODE END 0 */
+
+/**
+ * @brief The application entry point.
+ * @retval int
+ */
int main(void)
{
/* USER CODE BEGIN 1 */
@@ -362,31 +450,42 @@
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_LPTIM1_Init();
- MX_DMA_Init();
+ MX_DMA_Init();
MX_USART1_UART_Init();
MX_SPI1_Init();
- // MX_ADC_Init();
-
-// MX_TIM2_Init();
+ MX_ADC_Init();
+
+// MX_IWDG_Init();
/* USER CODE BEGIN 2 */
- LED_LG_ON;
- Program_Init();
-// LIS3DH_Data_Init();
- Dw1000_Init();
- Dw1000_App_Init();
-// HardWareTypeDiffConfig();
- dwt_configuresleep(DWT_PRESRV_SLEEP | DWT_CONFIG, DWT_WAKE_CS | DWT_WAKE_WK| DWT_SLP_EN);
- dwt_entersleep();
- DW_DISABLE;
- if(HAL_UART_Receive_DMA(&huart1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE))
- {
- Error_Handler();
- }
- HAL_Delay(2000);
+// LED_LG_ON;
+ Program_Init();
+ // LIS3DH_Data_Init();
+// Uwb_Lora_Switch(1,0);
+ Dw1000_Init();
+ Dw1000_App_Init();
+ Delay_Ms(10);
+// Uwb_Lora_Switch(0,0);
+ // HardWareTypeDiffConfig();
+ dwt_configuresleep(DWT_PRESRV_SLEEP | DWT_CONFIG, DWT_WAKE_CS | DWT_WAKE_WK| DWT_SLP_EN);
+ dwt_entersleep();
+ if(HAL_UART_Receive_DMA(&huart1,m_EUART_DMA_RXBuf,EUART_RX_BUF_SIZE))
+ {
+ Error_Handler();
+ }
+ Delay_Ms(2);
+// Uwb_Lora_Switch(0,1);
+ Lora_Init();
+// Radio.Sleep( );
+ Delay_Ms(10);
+// Uwb_Lora_Switch(0,0);
+ printf("RXD :66666\r\n");
+ usart_send[0]=0x55;
+ usart_send[1]=0xaa;
// mcu_sleep();
//LED0_BLINK;
// SystemPower_Config();
//HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
+
/* USER CODE END 2 */
/* Infinite loop */
@@ -396,56 +495,19 @@
/* USER CODE END WHILE */
/* USER CODE BEGIN 3 */
- if(g_start_send_flag)
- { static uint16_t blink_count=0;
- SystemClock_Config();
- g_start_send_flag = 0;
-
-// if(current_count>slot_startcount&¤t_count<slot_startcount+interval_count)
-// {
-// HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_SET);
-// }else{
-// HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
-// }
-// LED_TR_BLINK;s
-
-
- if(bat_percent>15)
- { LED_TB_ON;
- Tag_App();
- LED_TB_OFF;
- }else{
- LED_TR_ON;
- Tag_App();
- LED_TR_OFF;
- }
- //LED0_BLINK;
- IdleTask();
- if(waitusart_timer>0)
- {
- waitusart_timer--;
- }
- if(m_bEUARTTxEn==0&&waitusart_timer==0)
- {
- if(memcmp(g_com_map2,g_com_map,200)!=0)
- {
- SCB->AIRCR = 0X05FA0000|(unsigned int)0x04;
- }
-#ifndef DEBUG_MODE
-if(!HAL_GPIO_ReadPin(INPUT_5V_GPIO_Port,INPUT_5V_Pin))
- HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
-#endif
- }
-
-
- }else{
- IdleTask();
- }
+Lora_rx_open();
+
+ Lora_Tx_Poll();
+ HAL_IWDG_Refresh(&hiwdg);
+ IdleTask();
+// Radio.IrqProcess( ); // Process Radio IRQ
+// Anchor_App();
-// HAL_Delay(100);
- // Get_Battary();
-
- // LIS3DH_Data_Init();
+ #ifndef DEBUG_MODE
+ if(!HAL_GPIO_ReadPin(INPUT_5V_GPIO_Port,INPUT_5V_Pin))
+ HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);
+ #endif
+
}
/* USER CODE END 3 */
}
@@ -466,13 +528,15 @@
/** Configure LSE Drive Capability
*/
HAL_PWR_EnableBkUpAccess();
- __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
+ __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_HIGH);
/** Initializes the CPU, AHB and APB busses clocks
*/
- RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_LSE;
+ RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI|RCC_OSCILLATORTYPE_LSI
+ |RCC_OSCILLATORTYPE_LSE;
RCC_OscInitStruct.LSEState = RCC_LSE_ON;
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
+ RCC_OscInitStruct.LSIState = RCC_LSI_ON;
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
RCC_OscInitStruct.PLL.PLLMUL = RCC_PLLMUL_4;
@@ -509,11 +573,6 @@
* @param None
* @retval None
*/
-void MX_ADC_DeInit(void)
-{
- HAL_ADC_DeInit(&hadc);
- HAL_ADCEx_DisableVREFINT();
-}
void MX_ADC_Init(void)
{
@@ -532,7 +591,7 @@
hadc.Init.OversamplingMode = DISABLE;
hadc.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV2;
hadc.Init.Resolution = ADC_RESOLUTION_12B;
- hadc.Init.SamplingTime = ADC_SAMPLETIME_160CYCLES_5;
+ hadc.Init.SamplingTime = ADC_SAMPLETIME_1CYCLE_5;
hadc.Init.ScanConvMode = ADC_SCAN_DIRECTION_FORWARD;
hadc.Init.DataAlign = ADC_DATAALIGN_RIGHT;
hadc.Init.ContinuousConvMode = DISABLE;
@@ -561,6 +620,35 @@
HAL_ADCEx_EnableVREFINT();
HAL_ADCEx_Calibration_Start(&hadc,ADC_SINGLE_ENDED);
/* USER CODE END ADC_Init 2 */
+
+}
+
+/**
+ * @brief IWDG Initialization Function
+ * @param None
+ * @retval None
+ */
+static void MX_IWDG_Init(void)
+{
+
+ /* USER CODE BEGIN IWDG_Init 0 */
+
+ /* USER CODE END IWDG_Init 0 */
+
+ /* USER CODE BEGIN IWDG_Init 1 */
+
+ /* USER CODE END IWDG_Init 1 */
+ hiwdg.Instance = IWDG;
+ hiwdg.Init.Prescaler = IWDG_PRESCALER_256;
+ hiwdg.Init.Window = 4095;
+ hiwdg.Init.Reload = 4095;
+ if (HAL_IWDG_Init(&hiwdg) != HAL_OK)
+ {
+ Error_Handler();
+ }
+ /* USER CODE BEGIN IWDG_Init 2 */
+
+ /* USER CODE END IWDG_Init 2 */
}
@@ -634,69 +722,6 @@
/* USER CODE BEGIN SPI1_Init 2 */
__HAL_SPI_ENABLE(&hspi1);
/* USER CODE END SPI1_Init 2 */
-
-}
-
-/**
- * @brief TIM2 Initialization Function
- * @param None
- * @retval None
- */
-static void MX_TIM2_Init(void)
-{
-
- /* USER CODE BEGIN TIM2_Init 0 */
-
- /* USER CODE END TIM2_Init 0 */
-
- TIM_ClockConfigTypeDef sClockSourceConfig = {0};
- TIM_MasterConfigTypeDef sMasterConfig = {0};
- TIM_OC_InitTypeDef sConfigOC = {0};
-
- /* USER CODE BEGIN TIM2_Init 1 */
-
- /* USER CODE END TIM2_Init 1 */
- htim2.Instance = TIM2;
- htim2.Init.Prescaler = 9;
- htim2.Init.CounterMode = TIM_COUNTERMODE_UP;
- htim2.Init.Period = 1171;
- htim2.Init.ClockDivision = TIM_CLOCKDIVISION_DIV1;
- htim2.Init.AutoReloadPreload = TIM_AUTORELOAD_PRELOAD_DISABLE;
- if (HAL_TIM_Base_Init(&htim2) != HAL_OK)
- {
- Error_Handler();
- }
- sClockSourceConfig.ClockSource = TIM_CLOCKSOURCE_INTERNAL;
- if (HAL_TIM_ConfigClockSource(&htim2, &sClockSourceConfig) != HAL_OK)
- {
- Error_Handler();
- }
- if (HAL_TIM_PWM_Init(&htim2) != HAL_OK)
- {
- Error_Handler();
- }
- sMasterConfig.MasterOutputTrigger = TIM_TRGO_RESET;
- sMasterConfig.MasterSlaveMode = TIM_MASTERSLAVEMODE_DISABLE;
- if (HAL_TIMEx_MasterConfigSynchronization(&htim2, &sMasterConfig) != HAL_OK)
- {
- Error_Handler();
- }
- sConfigOC.OCMode = TIM_OCMODE_PWM1;
- sConfigOC.Pulse = 599;
- sConfigOC.OCPolarity = TIM_OCPOLARITY_HIGH;
- sConfigOC.OCFastMode = TIM_OCFAST_DISABLE;
- if (HAL_TIM_PWM_ConfigChannel(&htim2, &sConfigOC, TIM_CHANNEL_3) != HAL_OK)
- {
- Error_Handler();
- }
- /* USER CODE BEGIN TIM2_Init 2 */
-//if(HAL_TIM_PWM_Start(&htim2, TIM_CHANNEL_3) != HAL_OK)
-// {
-// /* Starting Error */
-// Error_Handler();
-// }
- /* USER CODE END TIM2_Init 2 */
- HAL_TIM_MspPostInit(&htim2);
}
@@ -785,7 +810,8 @@
HAL_GPIO_WritePin(GPIOB, BAT_MEAS_GND_Pin|PWR_CTL_Pin, GPIO_PIN_SET);
/*Configure GPIO pin Output Level */
- HAL_GPIO_WritePin(GPIOB, LED1_G_Pin|LED1_R_Pin|LED2_R_Pin, GPIO_PIN_RESET);
+ HAL_GPIO_WritePin(GPIOB, GPIO_PIN_10|LED1_G_Pin|LED1_R_Pin|RADIO_nRESET_Pin
+ |RADIO_NSS_Pin|GPIO_PIN_7, GPIO_PIN_RESET);
/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOA, DW_WKUP_Pin|DW_CTRL_Pin|LED2_G_Pin, GPIO_PIN_RESET);
@@ -823,18 +849,26 @@
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(USER_KEY_GPIO_Port, &GPIO_InitStruct);
+ /*Configure GPIO pin : RADIO_BUSY_Pin */
+ GPIO_InitStruct.Pin = RADIO_BUSY_Pin;
+ GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(RADIO_BUSY_GPIO_Port, &GPIO_InitStruct);
+
+ /*Configure GPIO pins : PB10 LED1_G_Pin LED1_R_Pin RADIO_nRESET_Pin
+ RADIO_NSS_Pin PB7 PWR_CTL_Pin */
+ GPIO_InitStruct.Pin = GPIO_PIN_10|LED1_G_Pin|LED1_R_Pin|RADIO_nRESET_Pin
+ |RADIO_NSS_Pin|GPIO_PIN_7|PWR_CTL_Pin;
+ GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+ HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
/*Configure GPIO pin : INPUT_5V_Pin */
GPIO_InitStruct.Pin = INPUT_5V_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_PULLDOWN;
HAL_GPIO_Init(INPUT_5V_GPIO_Port, &GPIO_InitStruct);
-
- /*Configure GPIO pins : LED1_G_Pin LED1_R_Pin LED2_R_Pin PWR_CTL_Pin */
- GPIO_InitStruct.Pin = LED1_G_Pin|LED1_R_Pin|LED2_R_Pin|PWR_CTL_Pin;
- GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
- GPIO_InitStruct.Pull = GPIO_NOPULL;
- GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
- HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
/*Configure GPIO pins : DW_WKUP_Pin DW_CTRL_Pin LED2_G_Pin */
GPIO_InitStruct.Pin = DW_WKUP_Pin|DW_CTRL_Pin|LED2_G_Pin;
@@ -843,15 +877,18 @@
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
- /*Configure GPIO pin : PWR_ON_Pin */
- GPIO_InitStruct.Pin = PWR_ON_Pin;
- GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
- GPIO_InitStruct.Pull = GPIO_PULLUP;
- HAL_GPIO_Init(PWR_ON_GPIO_Port, &GPIO_InitStruct);
+ /*Configure GPIO pin : RADIO_DIO1_Pin */
+ GPIO_InitStruct.Pin = RADIO_DIO1_Pin;
+ GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ HAL_GPIO_Init(RADIO_DIO1_GPIO_Port, &GPIO_InitStruct);
/* EXTI interrupt init*/
HAL_NVIC_SetPriority(EXTI0_1_IRQn, 1, 0);
HAL_NVIC_EnableIRQ(EXTI0_1_IRQn);
+
+ HAL_NVIC_SetPriority(EXTI2_3_IRQn, 1, 0);
+ HAL_NVIC_EnableIRQ(EXTI2_3_IRQn);
}
@@ -882,52 +919,34 @@
}
extern uint8_t tx_near_msg[80],stationary_flag;
float key_keeptime;
-extern float freqlost_count;
+extern float freqlost_count,range_lost_time;
+extern uint8_t lora_yingda_flag;
+uint8_t lora_yingdatime;
+extern uint8_t lora_chongfuyingda_flag;
+uint8_t no_data_chongqi_num;
void HAL_LPTIM_CompareMatchCallback(LPTIM_HandleTypeDef *hlptim)
{
- static uint8_t i=0;
- i++;
- g_start_send_flag=1;
- current_slotnum++;
- freqlost_count+=1/(float)tag_frequency;
- if(freqlost_count>FREQ_LOST_TIME)
- {
- tag_frequency = NOTAG_FREQ;
- }
- SetNextPollTime(tyncpoll_time);
- nomove_count+=1/(float)tag_frequency;
- if(motor_keeptime>0)
- {
- nomove_count+=1/(float)tag_frequency;
- }
- if(!GET_USERKEY)
- {
- key_keeptime+=1/(float)tag_frequency;
- if(key_keeptime>=KEY_KEEPRESET_TIME)
- {
- g_com_map[ACTIVE_INDEX]=!active_flag;
- save_com_map_to_flash();
- MOTOR_ON;
- HAL_Delay(2000);
- SCB->AIRCR = 0X05FA0000|(unsigned int)0x04;
- }
- }else{
- key_keeptime=0;
- }
-// if(nomove_count>STATIONARY_TIME)
-// {
-// stationary_flag = 1;
-// }else{
-// stationary_flag = 0;
-// }
-//if(nomove_count>=nomovesleeptime-1&&imu_enable)
-// {
-// tx_near_msg[TAGSTATE] = tx_near_msg[TAGSTATE]|GOINGSLEEPBIT;
-// }
-// if(nomove_count>nomovesleeptime&&imu_enable)
-// {
-// mcu_sleep();
-// }
+ SystemClock_Config();
+ lp_time++;
+ no_data_chongqi_num++;
+ lora_tx_flag=1;
+ Lora_Txcount=HAL_LPTIM_ReadCounter(&hlptim1);
+ Lora_Txcount=Lora_Txcount+32768/10*2;
+ if(Lora_Txcount>32768)
+ {Lora_Txcount=Lora_Txcount-32768;}
+ __HAL_LPTIM_COMPARE_SET(&hlptim1, Lora_Txcount);
+// if( no_data_chongqi_num>60)
+// {NVIC_SystemReset();}
+// if(lora_yingda_flag)
+// {
+// lora_yingdatime++;
+// if(lora_yingdatime>=2)
+// {lora_yingdatime=0;
+// lora_yingda_flag=0;
+// Lora_tx_mode();
+// Radio.Send( usart_send, 2);
+// }
+// }
}
/* USER CODE END 4 */
--
Gitblit v1.9.3