From 27956a4435c7cc37eee8fb908565b4ca8b1119ae Mon Sep 17 00:00:00 2001
From: yincheng.zhong <634916154@qq.com>
Date: 星期二, 28 二月 2023 16:15:07 +0800
Subject: [PATCH] V1.47 2
---
Src/application/dw_app.c | 295 +++++++++++++++++++++++++++++++----------------------------
1 files changed, 155 insertions(+), 140 deletions(-)
diff --git a/Src/application/dw_app.c b/Src/application/dw_app.c
index 8399bff..cbc0205 100644
--- a/Src/application/dw_app.c
+++ b/Src/application/dw_app.c
@@ -29,7 +29,9 @@
#include <stdio.h>
#include "beep.h"
#include "modbus.h"
+#include "CRC.h"
+//#define USART_INTEGRATE_OUTPUT
/*------------------------------------ Marcos ------------------------------------------*/
/* Inter-ranging delay period, in milliseconds. */
#define RNG_DELAY_MS 100
@@ -47,14 +49,14 @@
#define POLL_TX_TO_RESP_RX_DLY_UUS 150
/* This is the delay from Frame RX timestamp to TX reply timestamp used for calculating/setting the DW1000's delayed TX function. This includes the
* frame length of approximately 2.66 ms with above configuration. */
-#define RESP_RX_TO_FINAL_TX_DLY_UUS 1550
+#define RESP_RX_TO_FINAL_TX_DLY_UUS 410
/* Receive response timeout. See NOTE 5 below. */
#define RESP_RX_TIMEOUT_UUS 600
-#define DELAY_BETWEEN_TWO_FRAME_UUS 600
+#define DELAY_BETWEEN_TWO_FRAME_UUS 400
-#define POLL_RX_TO_RESP_TX_DLY_UUS 420
+#define POLL_RX_TO_RESP_TX_DLY_UUS 470
/* This is the delay from the end of the frame transmission to the enable of the receiver, as programmed for the DW1000's wait for response feature. */
#define RESP_TX_TO_FINAL_RX_DLY_UUS 200
/* Receive final timeout. See NOTE 5 below. */
@@ -68,22 +70,14 @@
#define FINAL_MSG_RESP_RX_TS_IDX 14
#define FINAL_MSG_FINAL_TX_TS_IDX 18
#define FINAL_MSG_TS_LEN 4
-
-
-enum enumtagstate
-{
- DISCPOLL,
- GETNEARMSG,
- NEARPOLL,
-}tag_state=GETNEARMSG;
static dwt_config_t config = {
- 2, /* Channel number. */
+ 5, /* Channel number. */
DWT_PRF_64M, /* Pulse repetition frequency. */
DWT_PLEN_128, /* Preamble length. */
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
9, /* TX preamble code. Used in TX only. */
9, /* RX preamble code. Used in RX only. */
- 0, /* Use non-standard SFD (Boolean) */
+ 1, /* Use non-standard SFD (Boolean) */
DWT_BR_6M8, /* Data rate. */
DWT_PHRMODE_STD, /* PHY header mode. */
(129 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
@@ -92,7 +86,7 @@
static uint8_t tx_sync_msg[14] = {0};
static uint8_t tx_final_msg[60] = {0};
static uint8_t tx_resp_msg[22] = {0};
-static uint8_t tx_near_msg[80] = {0};
+ uint8_t tx_near_msg[80] = {0};
static uint32_t frame_seq_nb = 0;
static uint32_t status_reg = 0;
@@ -266,7 +260,7 @@
u8 GetRandomSlotPos(uint32_t emptyslot)
{
u8 i,temp_value;
- temp_value = GetRandomValue();
+ temp_value = HAL_LPTIM_ReadCounter(&hlptim1);//GetRandomValue();
for(i=temp_value%32;i<max_slotpos;i++)
{
if(((emptyslot>>i)&0x1)==0)
@@ -291,9 +285,26 @@
u8 flag_finalsend,flag_getresponse,flag_rxon;
uint16_t current_count,start_count,end_count,lastsync_timer;
-u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum;
+u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum, para_update,para_len,stationary_flag=0;
u32 rec_tagpos_binary;
int16_t offset=2700;
+u8 current_freq,rec_freq;
+u8 motor_state,rec_remotepara_state,rec_remotepara[80];
+extern u16 last_lpcount;
+float freqlost_count = 0;
+void TagFreqProcess(u8 freq)
+{
+ if(freq>MAX_ANCFREQ||freq==0)
+ {
+ return;
+ }
+ if(freq==tag_frequency||freq>tag_frequency)
+ {
+ tag_frequency = freq;
+ freqlost_count = 0;
+ }
+}
+
void NearPoll(void)
{
@@ -301,9 +312,9 @@
uint32_t frame_len;
uint32_t final_tx_time;
u32 start_poll;
- u8 i,j,getsync_flag=0,timeout;
+ u8 i,j,getsync_flag=0,timeout,flag_ancreadpara=0;
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+ dwt_setrxtimeout(10000);
tag_succ_times = 0;
//GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
if(next_nearbase_num>=MAX_NEARBASE_NUM)
@@ -314,24 +325,27 @@
last_nearbase_num=next_nearbase_num;
nearbase_num=next_nearbase_num;
recbase_num=0;
-
- tx_near_msg[BATTARY_IDX] = Get_Battary();
- //tx_near_msg[BUTTON_IDX] = !READ_KEY0;
+// motor_state=0;
+ tx_near_msg[GROUP_ID_IDX] = group_id;
+ tx_near_msg[BATTARY_IDX] = bat_percent;
+ tx_near_msg[BUTTON_IDX] = !GET_USERKEY|stationary_flag<<1;
tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
- tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
+ tx_near_msg[MESSAGE_TYPE_IDX] = MBX_POLL;
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
dwt_writetxdata(13+2*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+ tx_near_msg[TAGCONFIGSUCCESS_INDEX] =0;
+ para_update = 0;
flag_finalsend=0;
flag_rxon=1;
flag_getresponse=0;
start_count=HAL_LPTIM_ReadCounter(&hlptim1);
recbase_num=0;
- timeout=ceil((float)nearbase_num*0.6)+20;
+ timeout=nearbase_num*SLOT_SCALE+4;
end_count=start_count+(timeout<<5);
if(end_count>=32768)
{end_count-=32768;}
@@ -351,6 +365,16 @@
dwt_forcetrxoff();
flag_rxon=0;
+ if(flag_ancreadpara)
+ {
+ u16 calCRC;
+ tx_near_msg[MESSAGE_TYPE_IDX] = MBX_PRAAREPLY;
+ memcpy(&tx_near_msg[MESSAGE_PARAREPLY_IDX],g_com_map,SENDANCPARA_LEN);
+ calCRC = CRC_Compute((uint8_t*)g_com_map,SENDANCPARA_LEN);
+ memcpy(&tx_near_msg[MESSAGE_PARAREPLY_IDX+SENDANCPARA_LEN],&calCRC,2);
+ dwt_writetxdata(14+SENDANCPARA_LEN, tx_near_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(14+SENDANCPARA_LEN, 0);//设定发送数据长度
+ }
dwt_setdelayedtrxtime(final_tx_time);
result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
flag_finalsend=0;
@@ -372,12 +396,23 @@
dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
dwt_rxenable(0);//打开接收
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == MBX_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&rx_buffer[GROUP_ID_IDX]==group_id) //判断接收到的数据是否是response数据
{ u16 rec_nearbaseid,rec_nearbasepos;
poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
recbase_num++;
memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
+ rec_remotepara_state = rx_buffer[MOTORSTATE_INDEX]>>4;
+ TagFreqProcess(rx_buffer[TAGFREQ_IDX]);
+ if(rec_remotepara_state != 0)
+ {
+ para_update = rec_remotepara_state;
+ memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],7);
+ if(para_update==2)
+ {
+ flag_ancreadpara = 1;
+ }
+ }
if(last_nearbase_num==0)
{
get_newbase=1;
@@ -409,6 +444,9 @@
exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
nearbase_distlist[rec_nearbasepos]=temp_dist;
+ if((rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
+ motor_state=rx_buffer[MOTORSTATE_INDEX]&0xf;
+
mainbase_lost_count=0;
flag_finalsend=1;
@@ -421,41 +459,35 @@
final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
- tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
+ tx_near_msg[MESSAGE_TYPE_IDX]=MBX_FINAL;
+ tx_near_msg[GROUP_ID_IDX] = group_id;
+
dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
flag_getresponse=1;
memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
- tyncpoll_time=0;
+
//时间同步
ancsync_time=((sync_timer)*1000+tmp_time);
last_slotnum=current_slotnum;
- current_slotnum=round((float)sync_timer/g_com_map[COM_INTERVAL])+1;
+ current_slotnum=((float)sync_timer/g_com_map[COM_INTERVAL])+1;
if(current_slotnum==last_slotnum-1)
{flag_getresponse=1;}
lastsync_timer=sync_timer;
offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
- SetNextPollTime(tyncpoll_time);
-
- // count_offset=sync_count-current_count-143;
- // current_slottimes=(ancsync_time-10000)/(g_com_map[COM_INTERVAL]*1000);
- // nextpoll_delaytime=tyncpoll_time*1000+g_com_map[COM_INTERVAL]*1000-((ancsync_time)%(g_com_map[COM_INTERVAL]*1000))-4300;
-// if(abs(ancsync_time-910000)<1000)
+// SetNextPollTime(tyncpoll_time);
+// if(rec_remotepara_state==1)
// {
-// nextpoll_delaytime+=10000;
-// }
-// if(nextpoll_delaytime<2000)
-// {
-// nextpoll_delaytime+=g_com_map[COM_INTERVAL]*1000;
-// }
-// lastpoll_count= current_count+(nextpoll_delaytime)/LPTIMER_LSB;
-// if(lastpoll_count>LPTIMER_1S_COUNT)
-// lastpoll_count-=LPTIMER_1S_COUNT;
-// __HAL_LPTIM_COMPARE_SET(&hlptim1, lastpoll_count);
- /////////////////////////////////////////
-// dwt_setdelayedtrxtime(final_tx_time);
-// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+// memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],REMOTEPARA_LEN);
+// memcpy(&g_com_map[COM_INTERVAL],&rec_remotepara[0],8);
+// memcpy(&g_com_map[POWER],&rec_remotepara[8],10);
+// if(g_com_map[COM_INTERVAL]>0&&g_com_map[COM_INTERVAL]<1000&&g_com_map[POWER]<67&&g_com_map[POWER]>0)
+// {save_com_map_to_flash();
+// delay_ms(100);
+// }
+// NVIC_SystemReset();
+// }
}else{
rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
@@ -471,11 +503,15 @@
memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
nearbase_distlist[rec_nearbasepos]=temp_dist;
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
+ if(motor_state<(rx_buffer[MOTORSTATE_INDEX]&0xf)&&(rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
+ {
+ motor_state=rx_buffer[MOTORSTATE_INDEX];
+ }
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
+
dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
-
//dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
@@ -490,24 +526,13 @@
}
// dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
}
-dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- nearbase_num=recbase_num;
- j=0;
- if(exsistbase_list[0]==0)
- {
-// u8 temp_adc,random_value;
-// random_value=0;
-// for(i=0;i<8;i++)
-// {
-// temp_adc=Get_ADC_Value();
-// random_value=random_value|((temp_adc&0x01)<<i);
-// }
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- // SetNextPollTime(tyncpoll_time);
- }
+ if(mainbase_lost_count>tag_frequency*BASELOST_STOPMOTOR_TIME)
+ {motor_state=0; }
+ dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ nearbase_num=recbase_num;
// tyncpoll_time=0;
next_nearbase_num=0;
+ j = 0;
for(i=0;i<last_nearbase_num+get_newbase;i++)
{
if(exsistbase_list[i]>0)
@@ -519,10 +544,11 @@
exsistbase_list[i]--;
}
}
-
- if(recbase_num<3)
- {next_nearbase_num=next_nearbase_num;}
- last_nearbase_num = next_nearbase_num;
+ if(mainbase_lost_count>1&&exsistbase_list[0] != 0)
+ {
+ last_lpcount+= HAL_LPTIM_ReadCounter(&hlptim1)%(g_com_map[COM_INTERVAL]*16);
+ }
+ last_nearbase_num = next_nearbase_num;
for(i=0;i<last_nearbase_num-1;i++)
{
for(j=0;j<last_nearbase_num-1;j++)
@@ -549,97 +575,86 @@
{
nearbaseid_list[i]=true_nearbase_idlist[i];
nearbase_distlist[i]=true_nearbase_distlist[i];
- if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==0xa)
+ if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==KEEP_TIMES)
{
memcpy(&usart_send[4+6*report_num],&nearbaseid_list[i],2);
memcpy(&usart_send[6+6*report_num],&nearbase_distlist[i],4);
report_num++;
}
}
+ #ifdef USART_INTEGRATE_OUTPUT
+ usart_send[0] = 0x55;
+ usart_send[1] = 0xAA;
+ usart_send[2] = 4;//正常模式
+ usart_send[3] = report_num*6+2;//正常模式
+ checksum = Checksum_u16(&usart_send[2],report_num*6+2);
+ memcpy(&usart_send[4+report_num*6],&checksum,2);
+ USART_puts(usart_send,6+report_num*6);
+ #endif
+
for(i=0;i<MAX_NEARBASE_NUM;i++)
{
nearbase_distlist[i]=0x1ffff;
}
-
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
-HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
-
-}
-u8 nearmsg_mainbase=0,rec_tagpos_emptylist[32];
-void GetNearMsg(void)
-{
- u32 start_poll,frame_len;
-if(nearmsg_mainbase)
- {nearmsg_mainbase=0;
- }else{
- nearmsg_mainbase=1;
- }
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&nearmsg_mainbase,2);
- memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
- tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
-
- dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
- dwt_writetxdata(12, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(12, 0);//设置超宽带发送数据长度
- dwt_starttx(DWT_START_TX_IMMEDIATE| DWT_RESPONSE_EXPECTED);
-
- /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
- {
- };
- if(status_reg==0xffffffff)
- {
- NVIC_SystemReset();
- }
- if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
- {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
- frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
- dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_MSG&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
- {
- nearbase_num=rx_buffer[NEARBASENUM_INDEX];
- memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
- //tagslotpos=rx_buffer[TAGSLOTPOS];
- memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
- slottime=ceil((nearbase_num+2)*0.3)+1;
- tyncpoll_time=tagslotpos*slottime;
- tag_state=NEARPOLL;
- }
- }else{
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- }
+//HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
+if(para_update==1)
+ {
+ uint16_t calCRC;
+ calCRC = CRC_Compute(rec_remotepara,5);
+ if(memcmp(&calCRC,&rec_remotepara[5],2)==0)
+ { uint8_t pack_msgtype,pack_index,pack_length;
+ pack_msgtype = rec_remotepara[0];
+ pack_index = rec_remotepara[1]*2;
+ pack_length = rec_remotepara[2];
+ if(pack_msgtype==2)
+ {
+ if( pack_index == 1)//MOTOR_ONTIME_INDEX)
+ {
+
+ // motor_keeptime = rec_remotepara[3];
+ }else if(pack_index == CNT_UPDATE)
+ {
+ if(rec_remotepara[3]==2)
+ {
+ EnterUWBUpdateMode();
+ }
+ }
+ else{
+ if(pack_index<200)
+ {
+ memcpy((uint8_t*)&g_com_map + pack_index, &rec_remotepara[3], pack_length);
+ //返回一个error状态
+ //SendComMap(pack_datalen,pack_index);
+ save_com_map_to_flash();
+ delay_ms(100);
+ NVIC_SystemReset();
+ }
+ }
+ }
+ }
+ }
}
+u32 id;
void Tag_App(void)//发送模式(TAG标签)
{
- u32 id;
+
//LED0_ON;
id = dwt_readdevid() ;
- while (DWT_DEVICE_ID != id)
+ while (DWT_DEVICE_ID != id)
{
- id = dwt_readdevid() ;
+ u8 iderror_count = 0;
+ id = dwt_readdevid() ;
+ if(iderror_count++>100)
+ {
+ printf("UWB芯片ID错误");
+ break;
+ }
}
-
+ delay_us(100);
g_Resttimer=0;
-// tag_state=DISCPOLL;
- switch(tag_state)
- {
- case DISCPOLL:
- // Poll();
- break;
- case GETNEARMSG:
-
- GetNearMsg();
-
- break;
- case NEARPOLL:
- //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_SET);
- NearPoll();
- //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_RESET);
- break;
- }
+ NearPoll();
dwt_entersleep();
+ bat_percent=Get_VDDVlotage();
}
--
Gitblit v1.9.3