From 732d7c16689595f70092080fa39eb1b39dabcb41 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期一, 19 四月 2021 16:08:24 +0800
Subject: [PATCH] V1.22 增加蜂鸣器功能 重新生成工程文件
---
Inc/stm32l0xx_hal_conf.h | 53 ++++++++++++++++++++++++++---------------------------
1 files changed, 26 insertions(+), 27 deletions(-)
diff --git a/Inc/stm32l0xx_hal_conf.h b/Inc/stm32l0xx_hal_conf.h
index c6fff26..fa5d085 100644
--- a/Inc/stm32l0xx_hal_conf.h
+++ b/Inc/stm32l0xx_hal_conf.h
@@ -2,22 +2,22 @@
******************************************************************************
* @file stm32l0xx_hal_conf.h
* @author MCD Application Team
- * @brief HAL configuration template file.
+ * @brief HAL configuration template file.
* This file should be copied to the application folder and renamed
* to stm32l0xx_hal_conf.h.
******************************************************************************
* @attention
*
- * <h2><center>© Copyright (c) 2016 STMicroelectronics.
+ * <h2><center>© Copyright (c) 2016 STMicroelectronics.
* All rights reserved.</center></h2>
*
* This software component is licensed by ST under BSD 3-Clause license,
- * the "License"; You may not use this file except in compliance with the
+ * the "License"; You may not use this file except in compliance with the
* License. You may obtain a copy of the License at:
* opensource.org/licenses/BSD-3-Clause
*
******************************************************************************
- */
+ */
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __STM32L0xx_HAL_CONF_H
@@ -32,10 +32,10 @@
/* ########################## Module Selection ############################## */
/**
- * @brief This is the list of modules to be used in the HAL driver
+ * @brief This is the list of modules to be used in the HAL driver
*/
-#define HAL_MODULE_ENABLED
+#define HAL_MODULE_ENABLED
#define HAL_ADC_MODULE_ENABLED
/*#define HAL_CRYP_MODULE_ENABLED */
/*#define HAL_COMP_MODULE_ENABLED */
@@ -50,7 +50,7 @@
/*#define HAL_RNG_MODULE_ENABLED */
/*#define HAL_RTC_MODULE_ENABLED */
#define HAL_SPI_MODULE_ENABLED
-/*#define HAL_TIM_MODULE_ENABLED */
+#define HAL_TIM_MODULE_ENABLED
/*#define HAL_TSC_MODULE_ENABLED */
#define HAL_UART_MODULE_ENABLED
/*#define HAL_USART_MODULE_ENABLED */
@@ -72,9 +72,9 @@
/**
* @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
* This value is used by the RCC HAL module to compute the system frequency
- * (when HSE is used as system clock source, directly or through the PLL).
+ * (when HSE is used as system clock source, directly or through the PLL).
*/
-#if !defined (HSE_VALUE)
+#if !defined (HSE_VALUE)
#define HSE_VALUE ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
#endif /* HSE_VALUE */
@@ -89,11 +89,11 @@
#if !defined (MSI_VALUE)
#define MSI_VALUE ((uint32_t)2097000U) /*!< Value of the Internal oscillator in Hz*/
#endif /* MSI_VALUE */
-
+
/**
* @brief Internal High Speed oscillator (HSI) value.
* This value is used by the RCC HAL module to compute the system frequency
- * (when HSI is used as system clock source, directly or through the PLL).
+ * (when HSI is used as system clock source, directly or through the PLL).
*/
#if !defined (HSI_VALUE)
#define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
@@ -102,7 +102,7 @@
/**
* @brief Internal High Speed oscillator for USB (HSI48) value.
*/
-#if !defined (HSI48_VALUE)
+#if !defined (HSI48_VALUE)
#define HSI48_VALUE ((uint32_t)48000000U) /*!< Value of the Internal High Speed oscillator for USB in Hz.
The real value may vary depending on the variations
in voltage and temperature. */
@@ -111,11 +111,11 @@
/**
* @brief Internal Low Speed oscillator (LSI) value.
*/
-#if !defined (LSI_VALUE)
+#if !defined (LSI_VALUE)
#define LSI_VALUE ((uint32_t)37000U) /*!< LSI Typical Value in Hz*/
#endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
The real value may vary depending on the variations
- in voltage and temperature.*/
+ in voltage and temperature.*/
/**
* @brief External Low Speed oscillator (LSE) value.
* This value is used by the UART, RTC HAL module to compute the system frequency
@@ -134,24 +134,24 @@
/* ########################### System Configuration ######################### */
/**
* @brief This is the HAL system configuration section
- */
-#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
-#define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */
-#define USE_RTOS 0U
-#define PREFETCH_ENABLE 0U
+ */
+#define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */
+#define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */
+#define USE_RTOS 0U
+#define PREFETCH_ENABLE 0U
#define PREREAD_ENABLE 1U
#define BUFFER_CACHE_DISABLE 0U
/* ########################## Assert Selection ############################## */
/**
- * @brief Uncomment the line below to expanse the "assert_param" macro in the
+ * @brief Uncomment the line below to expanse the "assert_param" macro in the
* HAL drivers code
*/
/* #define USE_FULL_ASSERT 1U */
/* Includes ------------------------------------------------------------------*/
/**
- * @brief Include module's header file
+ * @brief Include module's header file
*/
#ifdef HAL_RCC_MODULE_ENABLED
@@ -169,7 +169,7 @@
#ifdef HAL_DMA_MODULE_ENABLED
#include "stm32l0xx_hal_dma.h"
#endif /* HAL_DMA_MODULE_ENABLED */
-
+
#ifdef HAL_CORTEX_MODULE_ENABLED
#include "stm32l0xx_hal_cortex.h"
#endif /* HAL_CORTEX_MODULE_ENABLED */
@@ -181,7 +181,7 @@
#ifdef HAL_COMP_MODULE_ENABLED
#include "stm32l0xx_hal_comp.h"
#endif /* HAL_COMP_MODULE_ENABLED */
-
+
#ifdef HAL_CRC_MODULE_ENABLED
#include "stm32l0xx_hal_crc.h"
#endif /* HAL_CRC_MODULE_ENABLED */
@@ -201,7 +201,7 @@
#ifdef HAL_FLASH_MODULE_ENABLED
#include "stm32l0xx_hal_flash.h"
#endif /* HAL_FLASH_MODULE_ENABLED */
-
+
#ifdef HAL_I2C_MODULE_ENABLED
#include "stm32l0xx_hal_i2c.h"
#endif /* HAL_I2C_MODULE_ENABLED */
@@ -221,7 +221,7 @@
#ifdef HAL_LPTIM_MODULE_ENABLED
#include "stm32l0xx_hal_lptim.h"
#endif /* HAL_LPTIM_MODULE_ENABLED */
-
+
#ifdef HAL_PWR_MODULE_ENABLED
#include "stm32l0xx_hal_pwr.h"
#endif /* HAL_PWR_MODULE_ENABLED */
@@ -281,7 +281,7 @@
* @brief The assert_param macro is used for function's parameters check.
* @param expr: If expr is false, it calls assert_failed function
* which reports the name of the source file and the source
- * line number of the call that failed.
+ * line number of the call that failed.
* If expr is true, it returns no value.
* @retval None
*/
@@ -297,6 +297,5 @@
#endif
#endif /* __STM32L0xx_HAL_CONF_H */
-
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
--
Gitblit v1.9.3