From 748e84eba0b5d27b681652df9e23f9d5a28e9b9b Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期三, 04 十一月 2020 18:41:09 +0800
Subject: [PATCH] V2.7 医院发货的下一次版本，增加5v输入不休眠
---
Src/application/dw_app.c | 152 ++++++++++++++++++++++++++++++++++++++++----------
1 files changed, 122 insertions(+), 30 deletions(-)
diff --git a/Src/application/dw_app.c b/Src/application/dw_app.c
index 68993d6..d9b01a5 100644
--- a/Src/application/dw_app.c
+++ b/Src/application/dw_app.c
@@ -50,7 +50,7 @@
#define RESP_RX_TO_FINAL_TX_DLY_UUS 510
/* Receive response timeout. See NOTE 5 below. */
-#define RESP_RX_TIMEOUT_UUS 0
+#define RESP_RX_TIMEOUT_UUS 1000
#define DELAY_BETWEEN_TWO_FRAME_UUS 240
@@ -69,13 +69,14 @@
#define FINAL_MSG_FINAL_TX_TS_IDX 18
#define FINAL_MSG_TS_LEN 4
-
+#define STARTPOLL DISCPOLL
enum enumtagstate
{
+ REGPOLL,
DISCPOLL,
GETNEARMSG,
NEARPOLL,
-}tag_state=DISCPOLL;
+}tag_state=STARTPOLL;
static dwt_config_t config = {
2, /* Channel number. */
DWT_PRF_64M, /* Pulse repetition frequency. */
@@ -462,10 +463,10 @@
u8 exsistbase_list[MAX_NEARBASE_NUM],report_num,get_newbase=0;
u8 flag_finalsend,flag_getresponse,flag_rxon;
uint16_t current_count,start_count,end_count,lastsync_timer;
-
+extern u16 bigslot_num;
u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum, para_update,para_len,stationary_flag=0;
u32 rec_tagpos_binary;
-int16_t offset=2700;
+int16_t offset=4700,temptimer;
u8 motor_state,rec_remotepara_state,rec_remotepara[80];
void Poll(void)
{
@@ -535,9 +536,17 @@
tag_succ_times++;
LED0_BLINK;
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- SetNextPollTime(tyncpoll_time);
+ ancsync_time=((sync_timer)*1000+tmp_time);
+ last_slotnum=current_slotnum;
+ temptimer = sync_timer-10;
+ if(temptimer<0)
+ {temptimer+=1000;}
+ current_slotnum=((float)temptimer/(SLOTTIME_MS*bigslot_num))+1;
+ if(current_slotnum==last_slotnum-1)
+ {flag_getresponse=1;}
+ lastsync_timer=sync_timer;
+ offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
+ SetNextPollTime(tagslotpos);
if(temp_dist<mindist&&temp_dist!=0)
{
@@ -575,7 +584,7 @@
tyncpoll_time=(tagslotpos-1)*slottime;
}
mainbase_id=minid;
- //mainbase_id = 2;
+ //mainbase_id = 0x1;
}
u8 nearmsg_mainbase=0,rec_tagpos_emptylist[32],mainbase_type;;
void GetNearMsg(void)
@@ -622,19 +631,21 @@
tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
}
}
-uint8_t changemainbase_count=0;
+extern u8 userkey_state;
+uint8_t changemainbase_count=0,gotosleep_flag;
+uint32_t frame_len;
void NearPoll(void)
{
uint32_t temp1,temp2,dw_systime;
- uint32_t frame_len;
+
uint32_t final_tx_time;
u32 start_poll;
u8 i,j,getsync_flag=0,timeout;
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
tag_succ_times = 0;
- //GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
+
if(next_nearbase_num>=MAX_NEARBASE_NUM)
{
next_nearbase_num = MAX_NEARBASE_NUM-1;
@@ -642,17 +653,21 @@
HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_SET);
recbase_num=0;
- motor_state=0;
+// motor_state=0;
tx_near_msg[BATTARY_IDX] = bat_percent;
- tx_near_msg[BUTTON_IDX] = !GET_USERKEY|stationary_flag<<1;
+ tx_near_msg[BUTTON_IDX] = userkey_state|stationary_flag<<1|gotosleep_flag<<2;
tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
+
+ tx_near_msg[NEARP_TAGFREQ_INDEX] = tag_frequency;
+ tx_near_msg[NEARP_TAGSLOTPOS_INDEX] = tagslotpos;
+
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
- dwt_writetxdata(13+2*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
+ dwt_writetxdata(21+2*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(21+2*nearbase_num, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
tx_near_msg[TAGCONFIGSUCCESS_INDEX] =0;
@@ -741,12 +756,12 @@
//时间同步
ancsync_time=((sync_timer)*1000+tmp_time);
last_slotnum=current_slotnum;
- current_slotnum=((float)sync_timer/g_com_map[COM_INTERVAL])+1;
+ current_slotnum=((float)(sync_timer*10)/(SLOTTIME_MS*bigslot_num))+1;
if(current_slotnum==last_slotnum-1)
{flag_getresponse=1;}
lastsync_timer=sync_timer;
offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
- SetNextPollTime(tyncpoll_time);
+ SetNextPollTime(tagslotpos);
}else{
@@ -768,6 +783,7 @@
dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ userkey_state = !GET_USERKEY;
if(result==0)
{while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
{ };}
@@ -778,7 +794,7 @@
}
}else{
dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- if(recbase_num!=nearbase_num)
+ if(recbase_num!=nearbase_num+1)
{dwt_rxenable(0); }
// if(flag_rxon)
// {
@@ -787,20 +803,12 @@
}
// dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
}
+ dwt_forcetrxoff();
dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
j=0;
if(exsistbase_list[0]==0)
{
-// u8 temp_adc,random_value;
-// random_value=0;
-// for(i=0;i<8;i++)
-// {
-// temp_adc=Get_ADC_Value();
-// random_value=random_value|((temp_adc&0x01)<<i);
-// }
-// tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
-// tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- SetNextPollTime(tyncpoll_time);
+// SetNextPollTime(tagslotpos);
}
// tyncpoll_time=0;
next_nearbase_num=0;
@@ -899,6 +907,85 @@
HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
}
+extern uint8_t module_power,imu_enable,motor_enable;
+
+void Registor_Poll(void)
+{
+ static u8 regpoll_count=0;
+ tag_frequency = REGISTER_FREQUENCY;
+ bigslot_num = TOTAL_SLOTNUM/tag_frequency;
+ regpoll_count++;
+ if(regpoll_count%2)
+ {
+ if(tagslotpos--<2)
+ tagslotpos=TOTAL_SLOTNUM;
+ }
+ SetNextPollTime(tagslotpos);
+ dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+
+ tx_near_msg[REGP_TAGSTATE_INDEX] = !GET_USERKEY<<2|imu_enable<<1|motor_enable;
+ tx_near_msg[MESSAGE_TYPE_IDX] = REG_POLL;
+ tx_near_msg[REGP_FREQUENCY_INDEX] = 1000/g_com_map[COM_INTERVAL];
+ tx_near_msg[REGP_POWER_INDEX] = module_power;
+ memcpy(&tx_near_msg[REGP_VERSION_INDEX],&g_com_map[VERSION],2);
+ memcpy(&tx_near_msg[REGP_IMUTHRES_INDEX],&g_com_map[IMU_THRES],2);
+ memcpy(&tx_near_msg[REGP_NOMOVESLEEPTIME_INDEX],&g_com_map[NOMOVESLEEP_TIME],2);
+ dwt_writetxdata(21, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(21, 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
+ {
+ IdleTask();
+
+ };
+ if(status_reg==0xffffffff)
+ {
+ NVIC_SystemReset();
+ }
+ if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
+ {
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+ frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
+ dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == REG_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ { u16 rec_nearbaseid,rec_nearbasepos;
+
+ memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
+ tag_frequency = rx_buffer[REGR_TAGFREQ_INDEX];
+ bigslot_num = TOTAL_SLOTNUM/tag_frequency;
+ tagslotpos = rx_buffer[REGR_TAGSLOTPOS_INDEX];
+ //////////////////////////////////时间同步
+ memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
+ memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+// memcpy(&tagslotpos,&rx_buffer[TAGSLOTPOS],2);
+ tmp_time=tmp_time+450;
+ if(tmp_time>999)
+ {
+ tmp_time-=999;
+ sync_timer++;
+ if(sync_timer>=1010)
+ {sync_timer=0;}
+ }
+ ancsync_time=((sync_timer)*1000+tmp_time);
+ last_slotnum=current_slotnum;
+ temptimer = sync_timer-10;
+ if(temptimer<0)
+ {temptimer+=1000;}
+ current_slotnum=((float)temptimer/(SLOTTIME_MS*bigslot_num))+1;
+ if(current_slotnum==last_slotnum-1)
+ {flag_getresponse=1;}
+ lastsync_timer=sync_timer;
+ offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
+// SetNextPollTime(tagslotpos);
+ mainbase_id=rec_nearbaseid;
+ nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
+ tag_state = NEARPOLL;
+ }
+ }
+}
u32 id;
void Tag_App(void)//发送模式(TAG标签)
{
@@ -911,8 +998,13 @@
}
switch(tag_state)
{
+ case REGPOLL:
+ LED_LG_ON;
+ Registor_Poll();
+ LED_LG_OFF;
+ break;
case DISCPOLL:
- LED_LG_ON;
+ LED_LG_ON;
Poll();
LED_LG_OFF;
break;
--
Gitblit v1.9.3