From 8440ff4c3ee00bf9f478ec111efb19eaf02d25fc Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期二, 20 十月 2020 14:03:21 +0800
Subject: [PATCH] 飞机测试初步完成，采集第一次数据
---
Src/main.c | 26 ++++++++++++++++----------
1 files changed, 16 insertions(+), 10 deletions(-)
diff --git a/Src/main.c b/Src/main.c
index 8ea24f8..a0b6624 100644
--- a/Src/main.c
+++ b/Src/main.c
@@ -87,6 +87,7 @@
uint16_t slottime,max_slotpos;
uint16_t lastpoll_count,interval_count,slot_startcount,tag_frequency,lastpoll_time,current_time;
extern uint8_t module_power;
+extern float nomove_count;
uint8_t imu_enable,motor_enable;
u16 GetLPTime(void)
{
@@ -149,6 +150,7 @@
}
if(HAL_GPIO_ReadPin(INPUT_5V_GPIO_Port,INPUT_5V_Pin))
{
+ nomove_count = 0;
if(state5v==0)
{
state5v=1;
@@ -239,15 +241,17 @@
Usart1ParseDataCallback = UsartParseDataHandler;
parameter_init();
//deca_sleep(1000);
- g_com_map[VERSION] = 0x0110;
+ g_com_map[VERSION] = 0x0201;
#ifdef DEBUG_MODE
// g_com_map[DEV_ROLE]=1;
-// g_com_map[DEV_ID]=1;
+ g_com_map[DEV_ID]=0x123;
g_com_map[COM_INTERVAL]=100;
// g_com_map[MAX_REPORT_ANC_NUM]=1;
- g_com_map[NOMOVESLEEP_TIME]=10;
+// g_com_map[NOMOVESLEEP_TIME]=10;
+// g_com_map[IMU_ENABLE]=0;
#endif
-
+
+ // g_com_map[COM_INTERVAL]=100;
if(g_com_map[COM_INTERVAL]==0)
{
g_com_map[COM_INTERVAL]=100;
@@ -262,7 +266,8 @@
group_id=g_com_map[GROUP_ID];
dev_id = g_com_map[DEV_ID];
- slottime=ceil((double)g_com_map[MAX_REPORT_ANC_NUM]*SLOT_SCALE)+3;
+ //slottime=ceil((double)g_com_map[MAX_REPORT_ANC_NUM]*SLOT_SCALE)+3;
+ slottime = 5;
max_slotpos=g_com_map[COM_INTERVAL]/slottime;
tyncpoll_time=(g_com_map[DEV_ID]%max_slotpos)*slottime;
slot_startcount=tyncpoll_time*1000/LPTIMER_LSB;
@@ -341,7 +346,7 @@
/* Initialize all configured peripherals */
MX_GPIO_Init();
MX_LPTIM1_Init();
- MX_DMA_Init();
+ MX_DMA_Init();
MX_USART1_UART_Init();
MX_SPI1_Init();
MX_ADC_Init();
@@ -686,7 +691,7 @@
HAL_GPIO_WritePin(GPIOA, SCL_Pin|SDA_Pin|SPI_CS_Pin, GPIO_PIN_SET);
/*Configure GPIO pin Output Level */
- HAL_GPIO_WritePin(GPIOB, BAT_MEAS_GND_Pin|MOTOR_Pin, GPIO_PIN_SET);
+ HAL_GPIO_WritePin(GPIOB, BAT_MEAS_GND_Pin|MOTOR_Pin|PWR_CTL_Pin, GPIO_PIN_SET);
/*Configure GPIO pin Output Level */
HAL_GPIO_WritePin(GPIOB, LED1_G_Pin|LED1_R_Pin|LED2_R_Pin, GPIO_PIN_RESET);
@@ -733,8 +738,10 @@
GPIO_InitStruct.Pull = GPIO_PULLUP;
HAL_GPIO_Init(USER_KEY_GPIO_Port, &GPIO_InitStruct);
- /*Configure GPIO pins : MOTOR_Pin LED1_G_Pin LED1_R_Pin LED2_R_Pin */
- GPIO_InitStruct.Pin = MOTOR_Pin|LED1_G_Pin|LED1_R_Pin|LED2_R_Pin;
+ /*Configure GPIO pins : MOTOR_Pin LED1_G_Pin LED1_R_Pin LED2_R_Pin
+ PWR_CTL_Pin */
+ GPIO_InitStruct.Pin = MOTOR_Pin|LED1_G_Pin|LED1_R_Pin|LED2_R_Pin
+ |PWR_CTL_Pin;
GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
@@ -791,7 +798,6 @@
HAL_PWR_EnterSTANDBYMode();
}
extern uint8_t tx_near_msg[80],stationary_flag;
-extern float nomove_count;
float key_keeptime;
void HAL_LPTIM_CompareMatchCallback(LPTIM_HandleTypeDef *hlptim)
{
--
Gitblit v1.9.3