From cfa98f1edb2bb2d95b7323f7c5e7637f91aa4d66 Mon Sep 17 00:00:00 2001
From: zhyinch <zhyinch@gmail.com>
Date: 星期四, 29 四月 2021 10:13:23 +0800
Subject: [PATCH] 青岛第一次测试，有bug
---
Src/application/dw_app.c | 805 +++++++++++++++++++++++++++++++++++++-------------------
1 files changed, 531 insertions(+), 274 deletions(-)
diff --git a/Src/application/dw_app.c b/Src/application/dw_app.c
index 2fe757e..167813d 100644
--- a/Src/application/dw_app.c
+++ b/Src/application/dw_app.c
@@ -44,15 +44,15 @@
/* Delay between frames, in UWB microseconds. See NOTE 4 below. */
/* This is the delay from the end of the frame transmission to the enable of the receiver, as programmed for the DW1000's wait for response feature. */
-#define POLL_TX_TO_RESP_RX_DLY_UUS 150
+#define POLL_TX_TO_RESP_RX_DLY_UUS 10
/* This is the delay from Frame RX timestamp to TX reply timestamp used for calculating/setting the DW1000's delayed TX function. This includes the
* frame length of approximately 2.66 ms with above configuration. */
#define RESP_RX_TO_FINAL_TX_DLY_UUS 510
/* Receive response timeout. See NOTE 5 below. */
-#define RESP_RX_TIMEOUT_UUS 600
+#define RESP_RX_TIMEOUT_UUS 1000
-#define DELAY_BETWEEN_TWO_FRAME_UUS 400
+#define DELAY_BETWEEN_TWO_FRAME_UUS 240
#define POLL_RX_TO_RESP_TX_DLY_UUS 470
/* This is the delay from the end of the frame transmission to the enable of the receiver, as programmed for the DW1000's wait for response feature. */
@@ -69,21 +69,24 @@
#define FINAL_MSG_FINAL_TX_TS_IDX 18
#define FINAL_MSG_TS_LEN 4
-
+#define STARTPOLL SINGLEPOLL//#define SWITCHBASE_DIST
+#define SWITCHBASE_ZHUANDIAN
enum enumtagstate
{
+ REGPOLL,
DISCPOLL,
GETNEARMSG,
NEARPOLL,
-}tag_state=DISCPOLL;
+ SINGLEPOLL,
+}tag_state=STARTPOLL;
static dwt_config_t config = {
2, /* Channel number. */
DWT_PRF_64M, /* Pulse repetition frequency. */
- DWT_PLEN_128, /* Preamble length. */
+ DWT_PLEN_64, /* Preamble length. */
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
9, /* TX preamble code. Used in TX only. */
9, /* RX preamble code. Used in RX only. */
- 0, /* Use non-standard SFD (Boolean) */
+ 1, /* Use non-standard SFD (Boolean) */
DWT_BR_6M8, /* Data rate. */
DWT_PHRMODE_STD, /* PHY header mode. */
(129 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
@@ -196,6 +199,10 @@
tx_final_msg[MESSAGE_TYPE_IDX]=FINAL;
tx_sync_msg[MESSAGE_TYPE_IDX]=SYNC;
+ memcpy(&tx_poll_msg[GROUP_ID_IDX], &group_id, 1);
+ memcpy(&tx_final_msg[GROUP_ID_IDX], &group_id, 1);
+ memcpy(&tx_resp_msg[GROUP_ID_IDX], &group_id, 1);
+
memcpy(&tx_poll_msg[TAG_ID_IDX], &dev_id, 2);
memcpy(&tx_final_msg[TAG_ID_IDX], &dev_id, 2);
memcpy(&tx_resp_msg[ANCHOR_ID_IDX], &dev_id, 2);
@@ -241,7 +248,7 @@
u16 mainbase_id;
int32_t mainbase_dist;
uint8_t trygetnearmsg_times;
-u16 nearbaseid_list[MAX_NEARBASE_NUM],mainbase_id,true_nearbase_idlist[MAX_NEARBASE_NUM];
+u16 mainbase_id,true_nearbase_idlist[MAX_NEARBASE_NUM],nearbaseid_list[MAX_NEARBASE_NUM],nearbaseid_list2[MAX_NEARBASE_NUM];
u8 FindNearBasePos(u16 baseid)
{
u8 i;
@@ -284,36 +291,233 @@
}
return max_slotpos-1;
}
+void MODBUS_Poll(void)
+{
+ uint32_t frame_len;
+ uint32_t final_tx_time;
+ u32 start_poll;
+ u8 i,getsync_flag=0;
+ u8 bat_percent;
+ //LED0_ON;
+ //dwt_forcetrxoff();
+ g_Resttimer=0;
+ dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+ tag_succ_times = 0;
-int32_t mainbase_dist,nearbase_distlist[MAX_NEARBASE_NUM],true_nearbase_distlist[MAX_NEARBASE_NUM],true_exsistbase_list[MAX_NEARBASE_NUM],ancsync_time,nextpoll_delaytime,offsettimeus;
+ if(bat_percent>100)
+ bat_percent=100;
+ tx_poll_msg[BATTARY_IDX] = bat_percent;//Get_Battary();
+// tx_poll_msg[BUTTON_IDX] = !READ_KEY0;
+ tx_poll_msg[SEQUENCE_IDX] = frame_seq_nb++;
+// GPIO_WriteBit(GPIOA, GPIO_Pin_9, Bit_RESET);
+ for(i=0;i<g_com_map[MAX_REPORT_ANC_NUM];i++)
+ {
+ /* Write frame data to DW1000 and prepare transmission. See NOTE 7 below. */
+ tx_poll_msg[ANC_TYPE_IDX] = i;
+
+ dwt_writetxdata(sizeof(tx_poll_msg), tx_poll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(sizeof(tx_poll_msg), 0);//设置超宽带发送数据长度
+
+ /* Start transmission, indicating that a response is expected so that reception is enabled automatically after the frame is sent and the delay
+ * set by dwt_setrxaftertxdelay() has elapsed. */
+ dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+// start_poll = time32_incr;
+ /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
+ {
+ IdleTask();
+
+ };
+
+ /* Increment frame sequence number after transmission of the poll message (modulo 256). */
+ if(status_reg==0xffffffff)
+ {
+ NVIC_SystemReset();
+ }
+
+ if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
+ {
+ /* Clear good RX frame event and TX frame sent in the DW1000 status register. */
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+
+ /* A frame has been received, read it into the local buffer. */
+ frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
+
+ dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+
+
+ /* Check that the frame is the expected response from the companion "DS TWR responder" example.
+ * As the sequence number field of the frame is not relevant, it is cleared to simplify the validation of the frame. */
+
+ if (rx_buffer[GROUP_ID_IDX] == group_id&&rx_buffer[MESSAGE_TYPE_IDX] == RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,4)) //判断接收到的数据是否是response数据
+ { u16 anc_id_recv,rec_com_interval;
+ /* Retrieve poll transmission and response reception timestamp. */
+ poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
+ resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
+
+ if(getsync_flag==0&&g_com_map[DEV_ROLE])
+ {
+ getsync_flag=1;
+ memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
+ memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
+ tmp_time=tmp_time+450;
+ if(tmp_time>999)
+ {
+ tmp_time-=999;
+ sync_timer++;
+ if(sync_timer>=1010)
+ {sync_timer=0;}
+ }
+ // TIM3->CNT=tmp_time;
+ }
+ // memcpy(&hex_dist2, &rx_buffer[DIST_IDX], 4);
+ memcpy(&tx_final_msg[ANCHOR_ID_IDX], &rx_buffer[ANCHOR_ID_IDX], 4);
+ // memcpy(&rec_com_interval,&rx_buffer[ANCSEND_INTERVAL], 2);
+// if(rec_com_interval>4&&rec_com_interval!=g_com_map[COM_INTERVAL])
+// {
+// g_com_map[COM_INTERVAL]=rec_com_interval;
+// save_com_map_to_flash();
+// // delay_ms(100);
+// SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
+// }
+
+ /* Compute final message transmission time. See NOTE 9 below. */
+ final_tx_time = (resp_rx_ts + (RESP_RX_TO_FINAL_TX_DLY_UUS * UUS_TO_DWT_TIME)) >> 8;//计算final包发送时间，T5=T4+Treply2
+ dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+
+ /* Final TX timestamp is the transmission time we programmed plus the TX antenna delay. */
+ final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
+
+ /* Write all timestamps in the final message. See NOTE 10 below. */
+ final_msg_set_ts(&tx_final_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
+ final_msg_set_ts(&tx_final_msg[FINAL_MSG_RESP_RX_TS_IDX], resp_rx_ts);
+ final_msg_set_ts(&tx_final_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
+
+ /* Write and send final message. See NOTE 7 below. */
+
+ dwt_writetxdata(sizeof(tx_final_msg), tx_final_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(sizeof(tx_final_msg), 0);//设定发送数据长度
+ result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+
+ tag_succ_times++;
+
+ LED0_BLINK;
+
+ memcpy(&anc_id_recv,&rx_buffer[ANCHOR_ID_IDX],2);
+// if(hex_dist2!=0xffff)
+// {
+// g_Tagdist[anc_id_recv]= hex_dist2;
+// g_flag_Taggetdist[anc_id_recv]=0;
+//
+// if(!g_com_map[MODBUS_MODE])
+// {
+// hex_dist2 = hex_dist2;
+// usart_send[2] = 1;//正常模式
+// usart_send[3] = 17;//数据段长度
+// usart_send[4] = frame_seq_nb;//数据段长度
+// memcpy(&usart_send[5],&dev_id,2);
+// memcpy(&usart_send[7],&rx_buffer[ANCHOR_ID_IDX],2);
+//
+// memcpy(&usart_send[9],&hex_dist2,4);
+// usart_send[13] = bat_percent;
+// usart_send[14] = button;
+// checksum = Checksum_u16(&usart_send[2],17);
+// memcpy(&usart_send[19],&checksum,2);
+// UART_PushFrame(usart_send,21);
+// }
+// }
+ // memcpy(&Modbus_HoldReg[anc_id_recv*2],&hex_dist,4);
+ /* Poll DW1000 until TX frame sent event set. See NOTE 8 below. */
+ if(result==0)
+ {while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
+ { };
+ }
+ /* Clear TXFRS event. */
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_TXFRS);//清除标志位
+
+ /* Increment frame sequence number after transmission of the final message (modulo 256). */
+
+ random_delay_tim = 0;
+ }
+ else
+ {
+ random_delay_tim = DFT_RAND_DLY_TIM_MS; //如果通讯失败，将间隔时间增加5ms，避开因为多标签同时发送引起的冲突。
+ }
+ }
+ else
+ {
+ /* Clear RX error events in the DW1000 status register. */
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
+ random_delay_tim = DFT_RAND_DLY_TIM_MS;
+ }
+// deca_sleep(10);
+}
+// dwt_entersleep();
+
+
+ /* Execute a delay between ranging exchanges. */
+ delay_ms(30);
+
+}
+int32_t mainbase_dist,nearbase_switchdistlist[MAX_NEARBASE_NUM],nearbase_distlist[MAX_NEARBASE_NUM],true_nearbase_distlist[MAX_NEARBASE_NUM],true_exsistbase_list[MAX_NEARBASE_NUM],ancsync_time,nextpoll_delaytime,offsettimeus;
u8 anclost_times=0 , mainbase_lost_count=0;
u8 exsistbase_list[MAX_NEARBASE_NUM],report_num,get_newbase=0;
u8 flag_finalsend,flag_getresponse,flag_rxon;
uint16_t current_count,start_count,end_count,lastsync_timer;
-
+extern u16 bigslot_num;
u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum, para_update,para_len,stationary_flag=0;
u32 rec_tagpos_binary;
-int16_t offset=2700;
+int16_t offset=4700,temptimer;
u8 motor_state,rec_remotepara_state,rec_remotepara[80];
+
+
+#define SINGLEPOLL_BASENUM 10
+uint16_t singlepoll_baseid[SINGLEPOLL_BASENUM]={0x9733,0x9788,0x9798,0x8159,0x9797,0x9790,0x9799,0x9785,0x8169,0x8276};
+int32_t singlepoll_basedist[SINGLEPOLL_BASENUM];
+
+extern u8 userkey_state;
+extern float motor_keeptime;
+uint8_t changemainbase_count=0,gotosleep_flag,singlepoll_i;
+uint32_t frame_len;
+int32_t salvebase_mindist;
+int16_t intheight;
void Poll(void)
{
uint32_t frame_len;
uint32_t final_tx_time;
u32 start_poll;
int32_t mindist=999999,minid=-1,temp_dist;
- u8 i,getsync_flag=0;
+ u8 i,j,getsync_flag=0;
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
tag_succ_times = 0;
-
- for(i=0;i<3;i++)
+ frame_seq_nb++;
+ for(singlepoll_i=0;singlepoll_i<SINGLEPOLL_BASENUM;singlepoll_i++)
{
/* Write frame data to DW1000 and prepare transmission. See NOTE 7 below. */
- tx_poll_msg[ANC_TYPE_IDX] = i;
- dwt_writetxdata(sizeof(tx_poll_msg), tx_poll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(sizeof(tx_poll_msg), 0);//设置超宽带发送数据长度
+ nearbase_num = SINGLEPOLL_BASENUM-1;
+
+ tx_near_msg[BATTARY_IDX] = bat_percent;
+ tx_near_msg[BUTTON_IDX] = userkey_state|stationary_flag<<1|gotosleep_flag<<2;
+ tx_near_msg[SEQUENCE_IDX] = frame_seq_nb;
+ tx_near_msg[SEQUENCEH_IDX] = (frame_seq_nb)>>8;
+ tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
+ memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
+ memcpy(&tx_near_msg[NEARBASEID_INDEX+nearbase_num*2],&nearbase_distlist,nearbase_num*4+4);
+ intheight+=g_com_map[MAX_REPORT_ANC_NUM];
+ memcpy(&tx_near_msg[NEARBASEID_INDEX+nearbase_num*6+4],&intheight,2);
+ tx_near_msg[MESSAGE_TYPE_IDX] = SPOLL;
+
+ tx_near_msg[NEARP_TAGFREQ_INDEX] = tag_frequency;
+ tx_near_msg[NEARP_TAGSLOTPOS_INDEX] = tagslotpos;
+
+ memcpy(&tx_near_msg[ANCHOR_ID_IDX],&singlepoll_baseid[singlepoll_i],2);
+ dwt_writetxdata(28+6*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(28+6*nearbase_num, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+
/* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
{
@@ -327,7 +531,7 @@
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- if (rx_buffer[MESSAGE_TYPE_IDX] == RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&!memcmp(&rx_buffer[ANCHOR_ID_IDX],&singlepoll_baseid[singlepoll_i],2)) //判断接收到的数据是否是response数据
{
poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
@@ -346,10 +550,22 @@
if(sync_timer>=1010)
{sync_timer=0;}
}
+ ancsync_time=((sync_timer)*1000+tmp_time);
+ last_slotnum=current_slotnum;
+ temptimer = sync_timer-10;
+ if(temptimer<0)
+ {temptimer+=1000;}
+ //current_slotnum=((float)temptimer/(SLOTTIME_MS*bigslot_num))+1;
+ if(current_slotnum==last_slotnum-1)
+ {flag_getresponse=1;}
+ lastsync_timer=sync_timer;
+ //offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
+ SetNextPollTime(tagslotpos);
}
memcpy(&temp_dist, &rx_buffer[DIST_IDX], 4);
memcpy(&tx_final_msg[ANCHOR_ID_IDX], &rx_buffer[ANCHOR_ID_IDX], 4);
+ singlepoll_basedist[singlepoll_i] = temp_dist;
/* Compute final message transmission time. See NOTE 9 below. */
final_tx_time = (resp_rx_ts + (RESP_RX_TO_FINAL_TX_DLY_UUS * UUS_TO_DWT_TIME)) >> 8;//计算final包发送时间，T5=T4+Treply2
dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
@@ -363,17 +579,15 @@
tag_succ_times++;
LED0_BLINK;
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- SetNextPollTime(tyncpoll_time);
+
- if(temp_dist<mindist&&temp_dist!=0)
- {
- memcpy(&minid, &rx_buffer[ANCHOR_ID_IDX], 4);
- tag_state=GETNEARMSG;
- trygetnearmsg_times=5;
- mindist=temp_dist;
- }
+// if(temp_dist<mindist&&temp_dist!=0)
+// {
+// memcpy(&minid, &rx_buffer[ANCHOR_ID_IDX], 4);
+// tag_state=GETNEARMSG;
+// trygetnearmsg_times=10*tag_frequency;
+// mindist=temp_dist;
+// }
if(result==0)
{while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
{ };
@@ -384,32 +598,35 @@
}
else
{
+ singlepoll_basedist[singlepoll_i] = 0x1ffff;
random_delay_tim = DFT_RAND_DLY_TIM_MS; //如果通讯失败，将间隔时间增加5ms，避开因为多标签同时发送引起的冲突。
}
}
else
{
+ singlepoll_basedist[singlepoll_i] = 0x1ffff;
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
random_delay_tim = DFT_RAND_DLY_TIM_MS;
}
}
if(getsync_flag==0)
{
- tagslotpos--;
+// tagslotpos--;
if(tagslotpos==0||tagslotpos>max_slotpos)
{
tagslotpos=max_slotpos;
}
tyncpoll_time=(tagslotpos-1)*slottime;
}
- mainbase_id=minid;
+// mainbase_id=minid;
+// mainbase_id = 0x4;
}
u8 nearmsg_mainbase=0,rec_tagpos_emptylist[32],mainbase_type;;
void GetNearMsg(void)
{
u32 start_poll,frame_len;
-
+mainbase_id = 0x9724;
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
@@ -437,50 +654,66 @@
{
nearbase_num=rx_buffer[NEARBASENUM_INDEX];
memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
+ // tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
//tagslotpos=rx_buffer[TAGSLOTPOS];
memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
+ memcpy(nearbaseid_list2,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
//slottime=ceil((nearbase_num+2)*0.3)+1;
- tyncpoll_time=tagslotpos*slottime;
+ //tyncpoll_time=tagslotpos*slottime;
+ //tyncpoll_time=(g_com_map[DEV_ID]%max_slotpos)*slottime;
tag_state=NEARPOLL;
}
}else{
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
+// tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
}
}
+
void NearPoll(void)
{
- uint32_t temp1,temp2,dw_systime;
- uint32_t frame_len;
+ uint32_t temp1,temp2,dw_systime,mindist_slavebaseid;
+
uint32_t final_tx_time;
u32 start_poll;
u8 i,j,getsync_flag=0,timeout;
+ // USART_putc(current_slotnum);
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
tag_succ_times = 0;
- //GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
+ salvebase_mindist=999999;
if(next_nearbase_num>=MAX_NEARBASE_NUM)
{
next_nearbase_num = MAX_NEARBASE_NUM-1;
}
- HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_SET);
- last_nearbase_num=next_nearbase_num;
- nearbase_num=next_nearbase_num;
+// HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_SET);
+
recbase_num=0;
- motor_state=0;
+// motor_state=0;
tx_near_msg[BATTARY_IDX] = bat_percent;
- tx_near_msg[BUTTON_IDX] = !GET_USERKEY|stationary_flag<<1;
- tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
+ tx_near_msg[BUTTON_IDX] = userkey_state|stationary_flag<<1|gotosleep_flag<<2;
+ tx_near_msg[SEQUENCE_IDX] = frame_seq_nb;
+ tx_near_msg[SEQUENCEH_IDX] = (frame_seq_nb++)>>8;
tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
+ memcpy(&tx_near_msg[NEARBASEID_INDEX+nearbase_num*2],&nearbase_distlist,nearbase_num*4+4);
+ intheight+=g_com_map[MAX_REPORT_ANC_NUM];
+ memcpy(&tx_near_msg[NEARBASEID_INDEX+nearbase_num*6+4],&intheight,2);
tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
+
+ tx_near_msg[NEARP_TAGFREQ_INDEX] = tag_frequency;
+ tx_near_msg[NEARP_TAGSLOTPOS_INDEX] = tagslotpos;
+
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
- dwt_writetxdata(13+2*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
+ dwt_writetxdata(28+6*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(28+6*nearbase_num, 0);//设置超宽带发送数据长度
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+// for(i=0;i<nearbase_num+1;i++)
+// {
+// nearbase_distlist[i] = 0x1ffff;
+// }
+
tx_near_msg[TAGCONFIGSUCCESS_INDEX] =0;
para_update = 0;
flag_finalsend=0;
@@ -488,7 +721,7 @@
flag_getresponse=0;
start_count=HAL_LPTIM_ReadCounter(&hlptim1);
recbase_num=0;
- timeout=ceil((float)nearbase_num*SLOT_SCALE)+3;
+ timeout=ceil((float)nearbase_num*SLOT_SCALE)+2;
end_count=start_count+(timeout<<5);
if(end_count>=32768)
{end_count-=32768;}
@@ -500,20 +733,6 @@
current_count=HAL_LPTIM_ReadCounter(&hlptim1);
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
{
- if(flag_finalsend)
- {
- dw_systime=dwt_readsystimestamphi32();
- if(dw_systime>temp1&&dw_systime<temp2)
- {
-
- dwt_forcetrxoff();
- flag_rxon=0;
- dwt_setdelayedtrxtime(final_tx_time);
- result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- flag_finalsend=0;
- break;
- }
- }
current_count=HAL_LPTIM_ReadCounter(&hlptim1);
if(current_count>=end_count&¤t_count<end_count+15000)
break;
@@ -525,25 +744,220 @@
if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
{
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);//设定接收超时时间，0位没有超时时间
+ dwt_rxenable(0);//打开接收
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
- dwt_rxenable(0);//打开接收
+
if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
{ u16 rec_nearbaseid,rec_nearbasepos;
poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
recbase_num++;
memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
- if(last_nearbase_num==0)
+ if(rec_nearbaseid==mainbase_id)
{
- get_newbase=1;
- nearbaseid_list[0]=rec_nearbaseid;
- nearbase_num=1;
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
- }
- if(rec_nearbaseid==nearbaseid_list[0])
- {
+ //////////////////////////////////时间同步
+ memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
+ memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ dwt_forcetrxoff();
+ final_tx_time = (resp_rx_ts + ((RESP_RX_TO_FINAL_TX_DLY_UUS) * UUS_TO_DWT_TIME)) >> 8;
+ final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+nearbase_num*4], resp_rx_ts);
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
+ tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
+
+ if(rec_remotepara_state&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2))
+ {
+ para_update = 1;
+ tx_near_msg[TAGCONFIGSUCCESS_INDEX] = 1;
+ para_len = frame_len-22;
+ memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],para_len);
+ }
+ dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
+ dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
+ dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
+ result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ userkey_state = !GET_USERKEY;
+
+ memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
+ mainbase_dist=temp_dist;
+ nearbase_distlist[0] = temp_dist;
+ if((rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
+ motor_state=rx_buffer[MOTORSTATE_INDEX]&0xf;
+ rec_remotepara_state=rx_buffer[MOTORSTATE_INDEX]>>4;
+
+ mainbase_lost_count=0;
+ flag_finalsend=1;
+ memcpy(&mainbase_dist,&rx_buffer[DIST_IDX],4);
+
+
+ flag_getresponse=1;
+ //时间同步
+ tmp_time=tmp_time+450;
+ if(tmp_time>999)
+ {
+ tmp_time-=999;
+ sync_timer++;
+ if(sync_timer>=1000)
+ {sync_timer=0;}
+ }
+ ancsync_time=((sync_timer)*1000+tmp_time);
+ last_slotnum=current_slotnum;
+ current_slotnum=((float)(sync_timer*10 - tagslotpos*SLOTTIME_MS)/(SLOTTIME_MS*bigslot_num))+1;
+ if(current_slotnum==last_slotnum-1)
+ {flag_getresponse=1;}
+ lastsync_timer=sync_timer;
+ offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
+ SetNextPollTime(tagslotpos);
+ if(result==0)
+ {while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
+ { };}
+ break;
+ }else{
+
+ rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
+ exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
+ memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
+ memcpy(&nearbase_switchdistlist[rec_nearbasepos],&rx_buffer[NR_NEARSWITCH_DISTANCE],2);
+ nearbase_distlist[rec_nearbasepos+1]=temp_dist; // nearbase_distlist[1]对应 rec_nearbaseid[0]的距离
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
+ if(temp_dist<salvebase_mindist)
+ {
+ salvebase_mindist = temp_dist;
+ mindist_slavebaseid = rec_nearbaseid;
+ }
+ #ifdef SWITCHBASE_ZHUANDIAN
+ if(temp_dist<nearbase_switchdistlist[rec_nearbasepos]&&nearbase_switchdistlist[rec_nearbasepos]!=0&&temp_dist>0)
+ {
+ mainbase_id = rec_nearbaseid;
+ tag_state = GETNEARMSG;
+ }
+ #endif
+ }
+ }
+ }else{
+ dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ if(recbase_num!=nearbase_num+1)
+ {dwt_rxenable(0); }
+ // if(flag_rxon)
+// {
+ // dwt_rxenable(0);
+// }
+ }
+ // dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ }
+ if(flag_finalsend!=1)
+ {flag_finalsend = 2;}
+ dwt_forcetrxoff();
+dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+
+ if(mainbase_lost_count==0)
+ {
+ #ifdef SWITCHBASE_DIST
+ if(salvebase_mindist<mainbase_dist- THRESHOLD_CHANGE_MAINBASE_DIST )
+ {
+ changemainbase_count++;
+ if(changemainbase_count>tag_frequency*2)
+ {
+ mainbase_id = mindist_slavebaseid;
+ tag_state = GETNEARMSG;
+ }
+ }else{
+ changemainbase_count = 0;
+ }
+ #endif
+ }else if(mainbase_lost_count>10*tag_frequency)
+ {
+ tag_state = STARTPOLL;
+ }
+
+ if(para_update)
+ {
+ uint8_t pack_length = 0,pack_index = 0,pack_msgtype = 0;
+ pack_msgtype = rec_remotepara[0];
+ pack_index = rec_remotepara[1];
+ pack_length = rec_remotepara[2];
+ if(pack_msgtype==2)
+ {
+ if( pack_index == MOTOR_ONTIME_INDEX)
+ {
+ if(motor_keeptime==0)
+ motor_keeptime = rec_remotepara[3];
+ }else{
+ if(pack_index<200)
+ {
+ memcpy((uint8_t*)&g_com_map + pack_index, &rec_remotepara[3], pack_length);
+ //返回一个error状态
+ //SendComMap(pack_datalen,pack_index);
+ save_com_map_to_flash();
+ delay_ms(100);
+ NVIC_SystemReset();
+ }
+ }
+ }
+ }
+ for(i=0;i<nearbase_num;i++)
+ {
+ if(nearbaseid_list[i]!=nearbaseid_list2[i])
+ {
+ tag_state = GETNEARMSG;
+ }
+ }
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
+//HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
+
+}
+extern uint8_t module_power,imu_enable,motor_enable;
+
+void Registor_Poll(void)
+{
+ static u8 regpoll_count=0;
+ tag_frequency = REGISTER_FREQUENCY;
+ bigslot_num = TOTAL_SLOTNUM/tag_frequency;
+ regpoll_count++;
+ if(regpoll_count%2)
+ {
+ if(tagslotpos--<2)
+ tagslotpos=TOTAL_SLOTNUM;
+ }
+ SetNextPollTime(tagslotpos);
+ dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
+ dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+
+ tx_near_msg[REGP_TAGSTATE_INDEX] = !GET_USERKEY<<2|imu_enable<<1|motor_enable;
+ tx_near_msg[MESSAGE_TYPE_IDX] = REG_POLL;
+ tx_near_msg[REGP_FREQUENCY_INDEX] = 1000/g_com_map[COM_INTERVAL];
+ tx_near_msg[REGP_POWER_INDEX] = module_power;
+ memcpy(&tx_near_msg[REGP_VERSION_INDEX],&g_com_map[VERSION],2);
+ memcpy(&tx_near_msg[REGP_IMUTHRES_INDEX],&g_com_map[IMU_THRES],2);
+ memcpy(&tx_near_msg[REGP_NOMOVESLEEPTIME_INDEX],&g_com_map[NOMOVESLEEP_TIME],2);
+ dwt_writetxdata(21, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(21, 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
+ {
+ IdleTask();
+
+ };
+ if(status_reg==0xffffffff)
+ {
+ NVIC_SystemReset();
+ }
+ if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
+ {
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
+ frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
+ dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+ if (rx_buffer[MESSAGE_TYPE_IDX] == REG_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
+ { u16 rec_nearbaseid,rec_nearbasepos;
+
+ memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
+ tag_frequency = rx_buffer[REGR_TAGFREQ_INDEX];
+ bigslot_num = TOTAL_SLOTNUM/tag_frequency;
+ tagslotpos = rx_buffer[REGR_TAGSLOTPOS_INDEX];
//////////////////////////////////时间同步
memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
@@ -557,236 +971,79 @@
if(sync_timer>=1010)
{sync_timer=0;}
}
- // TIM3->CNT=tmp_time;
-// if(tagslotpos>max_slotpos)
-// tagslotpos=tagslotpos%(max_slotpos+1);
-// tyncpoll_time=(tagslotpos-1)*slottime;
- ////////////////////////////
- rec_nearbasepos=0;
- exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
- memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
- nearbase_distlist[rec_nearbasepos]=temp_dist;
- if((rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
- motor_state=rx_buffer[MOTORSTATE_INDEX]&0xf;
- rec_remotepara_state=rx_buffer[MOTORSTATE_INDEX]>>4;
-
- mainbase_lost_count=0;
- flag_finalsend=1;
- memcpy(&mainbase_dist,&rx_buffer[DIST_IDX],4);
- final_tx_time = (resp_rx_ts + ((RESP_RX_TO_FINAL_TX_DLY_UUS+DELAY_BETWEEN_TWO_FRAME_UUS*nearbase_num+500) * UUS_TO_DWT_TIME)) >> 8;
- temp1=final_tx_time-((850*UUS_TO_DWT_TIME)>>8);
- temp2=final_tx_time+((100*UUS_TO_DWT_TIME)>>8);
- // dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
- tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
- if(rec_remotepara_state&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2))
- {
- para_update = 1;
- tx_near_msg[TAGCONFIGSUCCESS_INDEX] = 1;
- para_len = frame_len-22;
- memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],para_len);
- }
-
- dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
- flag_getresponse=1;
- memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
-
-
- //时间同步
ancsync_time=((sync_timer)*1000+tmp_time);
last_slotnum=current_slotnum;
- current_slotnum=((float)sync_timer/g_com_map[COM_INTERVAL])+1;
+ temptimer = sync_timer-10;
+ if(temptimer<0)
+ {temptimer+=1000;}
+ current_slotnum=((float)temptimer/(SLOTTIME_MS*bigslot_num))+1;
if(current_slotnum==last_slotnum-1)
{flag_getresponse=1;}
lastsync_timer=sync_timer;
offsettimeus=ancsync_time-current_count*LPTIMER_LSB+offset;
- SetNextPollTime(tyncpoll_time);
-
-
- // count_offset=sync_count-current_count-143;
- // current_slottimes=(ancsync_time-10000)/(g_com_map[COM_INTERVAL]*1000);
- // nextpoll_delaytime=tyncpoll_time*1000+g_com_map[COM_INTERVAL]*1000-((ancsync_time)%(g_com_map[COM_INTERVAL]*1000))-4300;
-// if(abs(ancsync_time-910000)<1000)
-// {
-// nextpoll_delaytime+=10000;
-// }
-// if(nextpoll_delaytime<2000)
-// {
-// nextpoll_delaytime+=g_com_map[COM_INTERVAL]*1000;
-// }
-// lastpoll_count= current_count+(nextpoll_delaytime)/LPTIMER_LSB;
-// if(lastpoll_count>LPTIMER_1S_COUNT)
-// lastpoll_count-=LPTIMER_1S_COUNT;
-// __HAL_LPTIM_COMPARE_SET(&hlptim1, lastpoll_count);
- /////////////////////////////////////////
-// dwt_setdelayedtrxtime(final_tx_time);
-// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- }else{
- rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
-
- if(rec_nearbasepos>=last_nearbase_num) //发现新的基站
- {
- get_newbase=1;
- nearbase_num++;
- nearbaseid_list[rec_nearbasepos] = rec_nearbaseid;
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
- }
-
- exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
- memcpy(&temp_dist,&rx_buffer[DIST_IDX],4);
- nearbase_distlist[rec_nearbasepos]=temp_dist;
-
- if(motor_state<(rx_buffer[MOTORSTATE_INDEX]&0xf)&&(rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
- {
- motor_state=rx_buffer[MOTORSTATE_INDEX];
- }
- if(rec_remotepara_state&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2))
- {
- para_update = 1;
- tx_near_msg[TAGCONFIGSUCCESS_INDEX] = 1;
- para_len = frame_len-22;
- memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],para_len);
- }
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
- dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
-
-
- //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- // result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
- }
+// SetNextPollTime(tagslotpos);
+ mainbase_id=rec_nearbaseid;
+ nearbase_num=rx_buffer[NEARBASENUM_INDEX];
+ memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
+ memcpy(nearbaseid_list2,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
+ if(tagslotpos!=255)
+ tag_state = NEARPOLL;
+ }
}
- }else{
- dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- if(flag_rxon)
- {dwt_rxenable(0);
- }
- }
- // dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- }
-dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- nearbase_num=recbase_num;
- j=0;
- if(exsistbase_list[0]==0)
- {
-// u8 temp_adc,random_value;
-// random_value=0;
-// for(i=0;i<8;i++)
-// {
-// temp_adc=Get_ADC_Value();
-// random_value=random_value|((temp_adc&0x01)<<i);
-// }
- tagslotpos=GetRandomSlotPos(rec_tagpos_binary);
- tyncpoll_time = (tagslotpos--%max_slotpos)*slottime;
- SetNextPollTime(tyncpoll_time);
- }
- // tyncpoll_time=0;
- next_nearbase_num=0;
- for(i=0;i<last_nearbase_num+get_newbase;i++)
- {
- if(exsistbase_list[i]>0)
- {
- next_nearbase_num++;
- true_exsistbase_list[j]=exsistbase_list[i];
- true_nearbase_idlist[j]=nearbaseid_list[i];
- true_nearbase_distlist[j++]=nearbase_distlist[i];
- exsistbase_list[i]--;
- }
- }
-
- if(recbase_num<3)
- {next_nearbase_num=next_nearbase_num;}
- last_nearbase_num = next_nearbase_num;
- for(i=0;i<last_nearbase_num-1;i++)
- {
- for(j=0;j<last_nearbase_num-1;j++)
- {
- if(true_nearbase_distlist[j]>true_nearbase_distlist[j+1])
- {
- u32 temp_dist,temp_id,temp_exsis;
- temp_dist=true_nearbase_distlist[j];
- temp_id = true_nearbase_idlist[j];
- temp_exsis=true_exsistbase_list[i];
- true_nearbase_distlist[j]=true_nearbase_distlist[j+1];
- true_nearbase_idlist[j]=true_nearbase_idlist[j+1];
- true_exsistbase_list[j]=true_exsistbase_list[j+1];
-
- true_nearbase_distlist[j+1]=temp_dist;
- true_nearbase_idlist[j+1]=temp_id;
- true_exsistbase_list[j+1]=temp_exsis;
- }
- }
- }
-
- report_num=0;
- for (i=0;i<last_nearbase_num;i++)
- {
- nearbaseid_list[i]=true_nearbase_idlist[i];
- nearbase_distlist[i]=true_nearbase_distlist[i];
- if(nearbase_distlist[i]!=0x1ffff&&true_exsistbase_list[i]==0xa)
- {
- memcpy(&usart_send[4+6*report_num],&nearbaseid_list[i],2);
- memcpy(&usart_send[6+6*report_num],&nearbase_distlist[i],4);
- report_num++;
- }
- }
- for(i=0;i<MAX_NEARBASE_NUM;i++)
- {
- nearbase_distlist[i]=0x1ffff;
- }
- if(para_update)
- {
- uint8_t pack_length = 0,pack_index = 0,pack_msgtype = 0;
- pack_msgtype = rec_remotepara[0];
- pack_index = rec_remotepara[1];
- pack_length = rec_remotepara[2];
- if(pack_msgtype==2)
- {
- memcpy((uint8_t*)&g_com_map + pack_index, &rec_remotepara[3], pack_length);
- //返回一个error状态
- //SendComMap(pack_datalen,pack_index);
- save_com_map_to_flash();
- delay_ms(100);
- NVIC_SystemReset();
- }
- }
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
-HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
-
}
+u32 id,error_times=0;
+extern float Height;
void Tag_App(void)//发送模式(TAG标签)
{
- u32 id;
+
//LED0_ON;
+ SPIx_CS_GPIO->BRR = SPIx_CS;
+ delay_us(700);
+ GetPressAndHeight();
+ intheight = Height*100;
+ SPIx_CS_GPIO->BSRR = SPIx_CS;
id = dwt_readdevid() ;
while (DWT_DEVICE_ID != id)
{
+ // Dw1000_Init();
id = dwt_readdevid() ;
+ IdleTask();
+ if(error_times++>20)
+ {
+ printf("DW ID ERROR.\r\n");
+ SCB->AIRCR = 0X05FA0000|(unsigned int)0x04; //软复位回到bootloader
+ }
}
-
- g_Resttimer=0;
-// tag_state=DISCPOLL;
+ error_times = 0;
switch(tag_state)
{
+ case REGPOLL:
+ LED_LG_ON;
+ Registor_Poll();
+ LED_LG_OFF;
+ break;
case DISCPOLL:
+ LED_LG_ON;
Poll();
+ LED_LG_OFF;
break;
case GETNEARMSG:
-
- GetNearMsg();
-
+ trygetnearmsg_times--;
+ LED_LG_ON;
+ GetNearMsg();
+ LED_LG_OFF;
+ if(trygetnearmsg_times==0)
+ {
+ tag_state = STARTPOLL;
+ }
break;
- case NEARPOLL:
- //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_SET);
+ case NEARPOLL:
NearPoll();
- //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_RESET);
break;
+ case SINGLEPOLL:
+ Poll();
+ break;
}
dwt_entersleep();
}
--
Gitblit v1.9.3