From da6d7e68ec3d303e78e83a1adf17f638a0d49269 Mon Sep 17 00:00:00 2001
From: WXK <287788329@qq.com>
Date: 星期二, 26 十二月 2023 15:45:30 +0800
Subject: [PATCH] 1
---
Src/application/dw_app.c | 730 ++++++++++++++++++++++++++++++++-----------------------
1 files changed, 426 insertions(+), 304 deletions(-)
diff --git a/Src/application/dw_app.c b/Src/application/dw_app.c
index a9679ed..339297e 100644
--- a/Src/application/dw_app.c
+++ b/Src/application/dw_app.c
@@ -29,7 +29,9 @@
#include <stdio.h>
#include "beep.h"
#include "modbus.h"
+#include "CRC.h"
+//#define USART_INTEGRATE_OUTPUT
/*------------------------------------ Marcos ------------------------------------------*/
/* Inter-ranging delay period, in milliseconds. */
#define RNG_DELAY_MS 100
@@ -47,13 +49,14 @@
#define POLL_TX_TO_RESP_RX_DLY_UUS 150
/* This is the delay from Frame RX timestamp to TX reply timestamp used for calculating/setting the DW1000's delayed TX function. This includes the
* frame length of approximately 2.66 ms with above configuration. */
-#define RESP_RX_TO_FINAL_TX_DLY_UUS 850
+#define RESP_RX_TO_FINAL_TX_DLY_UUS 410
+
/* Receive response timeout. See NOTE 5 below. */
#define RESP_RX_TIMEOUT_UUS 600
-#define DELAY_BETWEEN_TWO_FRAME_UUS 240
+#define DELAY_BETWEEN_TWO_FRAME_UUS 400
-#define POLL_RX_TO_RESP_TX_DLY_UUS 420
+#define POLL_RX_TO_RESP_TX_DLY_UUS 470
/* This is the delay from the end of the frame transmission to the enable of the receiver, as programmed for the DW1000's wait for response feature. */
#define RESP_TX_TO_FINAL_RX_DLY_UUS 200
/* Receive final timeout. See NOTE 5 below. */
@@ -68,30 +71,29 @@
#define FINAL_MSG_FINAL_TX_TS_IDX 18
#define FINAL_MSG_TS_LEN 4
+//#define _UWB_4G
-enum enumtagstate
-{
- DISCPOLL,
- GETNEARMSG,
- NEARPOLL,
-}tag_state;
static dwt_config_t config = {
+#ifdef _UWB_4G
2, /* Channel number. */
+#else
+ 5,
+#endif
DWT_PRF_64M, /* Pulse repetition frequency. */
- DWT_PLEN_128, /* Preamble length. */
+ DWT_PLEN_64, /* Preamble length. */
DWT_PAC8, /* Preamble acquisition chunk size. Used in RX only. */
9, /* TX preamble code. Used in TX only. */
9, /* RX preamble code. Used in RX only. */
- 0, /* Use non-standard SFD (Boolean) */
+ 1, /* Use non-standard SFD (Boolean) */
DWT_BR_6M8, /* Data rate. */
DWT_PHRMODE_STD, /* PHY header mode. */
- (129 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
+ (65 + 8 - 8) /* SFD timeout (preamble length + 1 + SFD length - PAC size). Used in RX only. */
};
static uint8_t tx_poll_msg[20] = {0};
static uint8_t tx_sync_msg[14] = {0};
static uint8_t tx_final_msg[60] = {0};
static uint8_t tx_resp_msg[22] = {0};
-static uint8_t tx_near_msg[80] = {0};
+ uint8_t tx_near_msg[80] = {0};
static uint32_t frame_seq_nb = 0;
static uint32_t status_reg = 0;
@@ -102,7 +104,6 @@
static uint64_t poll_rx_ts;
static uint64_t resp_tx_ts;
static uint64_t final_rx_ts;
-static double tof;
int32_t anchor_dist_last_frm[TAG_NUM_IN_SYS],his_dist[TAG_NUM_IN_SYS]; ;
uint32_t tag_id = 0;
uint32_t tag_id_recv = 0;
@@ -112,7 +113,7 @@
uint32_t g_UWB_com_interval = 0;
float dis_after_filter; //当前距离值
LPFilter_Frac* p_Dis_Filter; //测距用的低通滤波器
-
+float range_lost_time = 0;
static uint64_t get_tx_timestamp_u64(void)
@@ -169,6 +170,7 @@
* For initialisation, DW1000 clocks must be temporarily set to crystal speed. After initialisation SPI rate can be increased for optimum
* performance. */
Reset_DW1000();//重启DW1000 /* Target specific drive of RSTn line into DW1000 low for a period. */
+ Spi_ChangePrescaler(SPIx_PRESCALER_SLOW); //设置为快速模式
dwt_initialise(DWT_LOADUCODE);//初始化DW1000
Spi_ChangePrescaler(SPIx_PRESCALER_FAST); //设置为快速模式
@@ -180,7 +182,13 @@
/* Apply default antenna delay value. See NOTE 1 below. */
dwt_setrxantennadelay(RX_ANT_DLY); //设置接收天线延迟
dwt_settxantennadelay(TX_ANT_DLY); //设置发射天线延迟
+// dwt_configcontinuousframemode(12480);
+// dwt_writetxdata(13, usart_send, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+// dwt_writetxfctrl(13, 0);//设置超宽带发送数据长度
+// dwt_starttx(DWT_START_TX_IMMEDIATE);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+//while(1)
+//{}
/* Set expected response's delay and timeout. See NOTE 4 and 5 below.
* As this example only handles one incoming frame with always the same delay and timeout, those values can be set here once for all. */
//设置接收超时时间
@@ -188,7 +196,7 @@
void Dw1000_App_Init(void)
{
//g_com_map[DEV_ID] = 0x0b;
- tag_state=DISCPOLL;
+ //tag_state=DISCPOLL;
tx_poll_msg[MESSAGE_TYPE_IDX]=POLL;
tx_resp_msg[MESSAGE_TYPE_IDX]=RESPONSE;
tx_final_msg[MESSAGE_TYPE_IDX]=FINAL;
@@ -236,118 +244,10 @@
u16 anclist_num=0,anclist_pos; //list 总数量和当前位置
u16 ancid_list[TAG_NUM_IN_SYS];
u8 nearbase_num;
-u16 nearbaseid_list[10],mainbase_id;
-int32_t mainbase_dist,nearbase_distlist[10];
+u16 mainbase_id;
+int32_t mainbase_dist;
uint8_t trygetnearmsg_times;
-void Poll(void)
-{
- uint32_t frame_len;
- uint32_t final_tx_time;
- u32 start_poll;
- int32_t mindist=999999,minid=-1,temp_dist;
- u8 i,getsync_flag=0;
- dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
- tag_succ_times = 0;
-// GPIO_WriteBit(GPIOA, GPIO_Pin_9, Bit_RESET);
- for(i=0;i<g_com_map[MAX_REPORT_ANC_NUM];i++)
- {
- /* Write frame data to DW1000 and prepare transmission. See NOTE 7 below. */
- tx_poll_msg[ANC_TYPE_IDX] = i;
- dwt_writetxdata(sizeof(tx_poll_msg), tx_poll_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(sizeof(tx_poll_msg), 0);//设置超宽带发送数据长度
- dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
-
- /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
- {
- };
- if(status_reg==0xffffffff)
- {
- NVIC_SystemReset();
- }
- if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
- {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
- frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
- dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- if (rx_buffer[MESSAGE_TYPE_IDX] == RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
- {
- poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
- resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
- if(getsync_flag==0)
- {
- getsync_flag=1;
- memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
- memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
- memcpy(&tagslotpos,&rx_buffer[TAGSLOTPOS],2);
- tmp_time=tmp_time+450;
- if(tmp_time>999)
- {
- tmp_time-=999;
- sync_timer++;
- if(sync_timer>=1010)
- {sync_timer=0;}
- }
-// TIM3->CNT=tmp_time;
-// if(tagslotpos>max_slotpos)
-// tagslotpos=tagslotpos%(max_slotpos+1);
-// tyncpoll_time=(tagslotpos-1)*slottime;
- }
-
- memcpy(&temp_dist, &rx_buffer[DIST_IDX], 4);
- memcpy(&tx_final_msg[ANCHOR_ID_IDX], &rx_buffer[ANCHOR_ID_IDX], 4);
- /* Compute final message transmission time. See NOTE 9 below. */
- final_tx_time = (resp_rx_ts + (RESP_RX_TO_FINAL_TX_DLY_UUS * UUS_TO_DWT_TIME)) >> 8;//计算final包发送时间，T5=T4+Treply2
- dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
- final_msg_set_ts(&tx_final_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
- final_msg_set_ts(&tx_final_msg[FINAL_MSG_RESP_RX_TS_IDX], resp_rx_ts);
- final_msg_set_ts(&tx_final_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
- dwt_writetxdata(sizeof(tx_final_msg), tx_final_msg, 0);//将发送数据写入DW1000
- dwt_writetxfctrl(sizeof(tx_final_msg), 0);//设定发送数据长度
- result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- tag_succ_times++;
- LED0_BLINK;
-
- if(temp_dist<mindist)
- {
- memcpy(&minid, &rx_buffer[ANCHOR_ID_IDX], 4);
- tag_state=GETNEARMSG;
- trygetnearmsg_times=5;
- mindist=temp_dist;
- }
- if(result==0)
- {while (!(dwt_read32bitreg(SYS_STATUS_ID) & SYS_STATUS_TXFRS))//不断查询芯片状态直到发送完成
- { };
- }
- /* Clear TXFRS event. */
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_TXFRS);//清除标志位
- random_delay_tim = 0;
- }
- else
- {
- random_delay_tim = DFT_RAND_DLY_TIM_MS; //如果通讯失败，将间隔时间增加5ms，避开因为多标签同时发送引起的冲突。
- }
- }
- else
- {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
- random_delay_tim = DFT_RAND_DLY_TIM_MS;
- }
-}
- if(getsync_flag==0)
- {
- tagslotpos--;
- if(tagslotpos==0||tagslotpos>max_slotpos)
- {
- tagslotpos=max_slotpos;
- }
- tyncpoll_time=(tagslotpos-1)*slottime;
- }
- mainbase_id=minid;
-}
-
+u16 nearbaseid_list[MAX_NEARBASE_NUM],mainbase_id,true_nearbase_idlist[MAX_NEARBASE_NUM];
u8 FindNearBasePos(u16 baseid)
{
u8 i;
@@ -359,89 +259,241 @@
}
u8 recbase_num=0;
#define CHANGE_BASE_THRESHOLD 5
-void NearAncSelect(void)
-{static u16 last_mainbase_id,change_base_count;
- int32_t nearbase_mindist=99999, nearbase_minpos;
- u8 i;
- for(i=0;i<recbase_num-1;i++)
+uint8_t GetRandomValue(void)
+{
+ uint8_t random_value=0,temp_adc,i;
+ for(i=0;i<8;i++)
{
- if(nearbase_mindist>nearbase_distlist[i])
- {
- nearbase_mindist=nearbase_distlist[i];
- nearbase_minpos=i;
- }
+ temp_adc=Get_ADC_Value();
+ random_value=random_value|((temp_adc&0x01)<<i);
}
- if(nearbase_mindist<mainbase_dist-THRESHOLD_CHANGE_MAINBASE_DIST)
- {
- if(last_mainbase_id==nearbaseid_list[nearbase_minpos])
- {
- change_base_count++;
- if(change_base_count>CHANGE_BASE_THRESHOLD)
- {
- mainbase_id=last_mainbase_id;
- tag_state=GETNEARMSG;
- }
- }else{
- change_base_count=0;
- }
- last_mainbase_id=nearbaseid_list[nearbase_minpos];
- }else{
- change_base_count=0;
- }
+ return random_value;
}
-u8 anclost_times=0;
-uint16_t current_count,start_count,end_count;
+u8 GetRandomSlotPos(uint32_t emptyslot)
+{
+ u8 i,temp_value;
+ temp_value = HAL_LPTIM_ReadCounter(&hlptim1);//GetRandomValue();
+ for(i=temp_value%32;i<max_slotpos;i++)
+ {
+ if(((emptyslot>>i)&0x1)==0)
+ {
+ return i;
+ }
+ }
+
+ for(i=1;i<max_slotpos;i++)
+ {
+ if(((emptyslot>>i)&0x1)==0)
+ {
+ return i;
+ }
+ }
+return max_slotpos-1;
+}
+
+int32_t mainbase_dist,nearbase_distlist[MAX_NEARBASE_NUM],true_nearbase_distlist[MAX_NEARBASE_NUM],true_exsistbase_list[MAX_NEARBASE_NUM],ancsync_time,nextpoll_delaytime,offsettimeus;
+u8 anclost_times=0 , mainbase_lost_count=0;
+u8 exsistbase_list[MAX_NEARBASE_NUM],report_num,get_newbase=0;
+u8 flag_finalsend,flag_getresponse,flag_rxon;
+uint16_t current_count,start_count,end_count,lastsync_timer;
+
+u8 nearbase_num=0,last_nearbase_num,next_nearbase_num,last_slotnum, para_update,para_len,stationary_flag=0;
+u32 rec_tagpos_binary;
+int16_t offset=2700;
+u8 current_freq,rec_freq;
+u8 motor_state,rec_remotepara_state,rec_remotepara[80];
+extern u16 last_lpcount;
+float freqlost_count = 0;
+void TagFreqProcess(u8 freq)
+{
+ if(freq>MAX_ANCFREQ||freq==0)
+ {
+ return;
+ }
+ if(freq==tag_frequency||freq>tag_frequency)
+ {
+ tag_frequency = freq;
+ freqlost_count = 0;
+ }
+}
+#define FREQ_OFFSET_MULTIPLIER (998.4e6/2.0/1024.0/131072.0)
+#define FREQ_OFFSET_MULTIPLIER_110KB (998.4e6/2.0/8192.0/131072.0)
+
+#define HERTZ_TO_PPM_MULTIPLIER_CHAN_1 (-1.0e6/3494.4e6)
+#define HERTZ_TO_PPM_MULTIPLIER_CHAN_2 (-1.0e6/3993.6e6)
+#define HERTZ_TO_PPM_MULTIPLIER_CHAN_3 (-1.0e6/4492.8e6)
+#define HERTZ_TO_PPM_MULTIPLIER_CHAN_5 (-1.0e6/6489.6e6)
+u16 rec_maxrangelen;//rec_anc_signalpower[MAX_NEARBASE_ANCNUM];
+float clockOffsetRatio;
+double rtd_init, rtd_resp;
+double tof,distance;
+extern int32_t dwt_readcarrierintegrator(void) ;
+uint32_t testtimer2,anc_pollrx[MAX_NEARBASE_NUM],anc_resptx[MAX_NEARBASE_NUM],tag_resprx[MAX_NEARBASE_NUM];
+int32_t anc_clockoffset[MAX_NEARBASE_NUM];
+int16_t anc_distoffset[MAX_NEARBASE_NUM];
+int32_t test2;
+uint16_t u16_nearbase_distlist[MAX_NEARBASE_NUM];
+uint8_t get_newdist,notenoughdist_count;
+void SetANCTimestap(uint8_t i,uint8_t* pollrx,uint8_t* resptx,uint32_t resprx,uint8_t* distoffset) //写入时间戳信息
+{
+ memcpy(&anc_pollrx[i],pollrx,4);
+ memcpy(&anc_resptx[i],resptx,4);
+ memcpy(&tag_resprx[i],&resprx,4);
+ memcpy(&anc_distoffset[i],distoffset,2);
+ anc_clockoffset[i] = test2;
+}
+void CalculateDists(void) //计算距离
+{
+ for(int i=0;i<MAX_NEARBASE_NUM;i++)
+ {
+ //rec_anc_signalpower[i] = exsistbase_list[i];
+ if(exsistbase_list[i]==KEEP_TIMES)
+ {
+
+ // exsistbase_list[i]--;
+#ifdef _UWB_4G
+ clockOffsetRatio = anc_clockoffset[i] * (FREQ_OFFSET_MULTIPLIER * HERTZ_TO_PPM_MULTIPLIER_CHAN_2 / 1.0e6) ;
+#else
+ clockOffsetRatio = anc_clockoffset[i] * (FREQ_OFFSET_MULTIPLIER * HERTZ_TO_PPM_MULTIPLIER_CHAN_5 / 1.0e6) ;
+#endif
+ rtd_init = tag_resprx[i] - poll_tx_ts&0xffffffff;
+ rtd_resp = anc_resptx[i] - anc_pollrx[i];
+ tof = ((rtd_init - rtd_resp * (1 - clockOffsetRatio)) / 2.0) * DWT_TIME_UNITS;
+ distance = tof * SPEED_OF_LIGHT;
+ if(distance>-10&&distance<1000)
+ nearbase_distlist[i] = distance*100+anc_distoffset[i];
+ range_lost_time=0;
+ }else{
+ // nearbase_distlist[i] = 0x1ffff;
+ }
+
+ }
+}
+extern uint8_t module_power,imu_enable,motor_enable;
+void Registor_Poll(void)
+{
+ static u8 regpoll_count=0;
+ u8 timeout;
+
+ tx_near_msg[MESSAGE_TYPE_IDX] = MBX_REG;
+ tx_near_msg[REGP_TAGSTATE_INDEX] = !GET_USERKEY<<2|imu_enable<<1|motor_enable;
+ tx_near_msg[REGP_FREQUENCY_INDEX] = bat_percent;
+ tx_near_msg[REGP_POWER_INDEX] = module_power;
+ memcpy(&tx_near_msg[REGP_VERSION_INDEX],&g_com_map[VERSION],2);
+ memcpy(&tx_near_msg[REGP_IMUTHRES_INDEX],&g_com_map[GROUP_ID],2);
+ memcpy(&tx_near_msg[REGP_NOMOVESLEEPTIME_INDEX],&g_com_map[DIST_OFFSET],2);
+ memcpy(&tx_near_msg[REGP_HEIGHTOFFSET_INDEX],&g_com_map[MAX_REPORT_ANC_NUM],2);
+ dwt_writetxdata(23, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(23, 0);//设置超宽带发送数据长度
+ dwt_starttx(DWT_START_TX_IMMEDIATE);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
+ start_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ timeout=50;
+ end_count=start_count+(timeout<<2);
+ while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_TXFRS)))//不断查询芯片状态直到成功接收或者发生错误
+ {
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ if(current_count>=end_count&¤t_count<end_count+15000)
+ break;
+
+ };
+
+}
+u16 numceshi;
+u16 rec_nearbaseid,rec_nearbasepos;
+extern u16 poll_startcount;
void NearPoll(void)
{
- static u8 mainbase_lost_count=0,flag_finalsend;
+
uint32_t temp1,temp2,dw_systime;
uint32_t frame_len;
uint32_t final_tx_time;
- u32 start_poll;
- u8 i,getsync_flag=0,timeout;
+ u32 start_poll,timeout;
+ u8 i,j,getsync_flag=0,flag_ancreadpara=0;
dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
+ dwt_setrxtimeout(0);
tag_succ_times = 0;
- tx_near_msg[BATTARY_IDX] = Get_Battary();
- //tx_near_msg[BUTTON_IDX] = !READ_KEY0;
+ //GPIO_WriteBit(GPIOA, GPIO_Pin_10, Bit_SET);
+ if(nearbase_num>=MAX_NEARBASE_NUM)
+ {
+ nearbase_num = MAX_NEARBASE_NUM-1;
+ }
+ recbase_num=0;
+ for(uint8_t i=0;i<nearbase_num;i++) //标签距离32位转成16位
+ {
+ u16_nearbase_distlist[i] = nearbase_distlist[i];
+ }
+ tx_near_msg[GROUP_ID_IDX] = group_id;
+ tx_near_msg[BATTARY_IDX] = bat_percent;
+ tx_near_msg[BUTTON_IDX] = !GET_USERKEY|stationary_flag<<1;
tx_near_msg[SEQUENCE_IDX] = frame_seq_nb++;
tx_near_msg[NEARBASENUM_INDEX] = nearbase_num;
memcpy(&tx_near_msg[NEARBASEID_INDEX],&nearbaseid_list,nearbase_num*2);
- tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_POLL;
+ memcpy(&tx_near_msg[NEARBASEID_INDEX+nearbase_num*2],&u16_nearbase_distlist,nearbase_num*2);
+ tx_near_msg[MESSAGE_TYPE_IDX] = MBX_POLL;
memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
- dwt_writetxdata(13+2*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(13+2*nearbase_num, 0);//设置超宽带发送数据长度
+ dwt_writetxdata(13+4*nearbase_num, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
+ dwt_writetxfctrl(13+4*nearbase_num, 0);//设置超宽带发送数据长度
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ while(current_count<poll_startcount||current_count>poll_startcount+16384)
+ {
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ if(current_count<poll_startcount-300)
+ {
+ break;
+ }
+ }
+
dwt_starttx(DWT_START_TX_IMMEDIATE | DWT_RESPONSE_EXPECTED);//开启发送，发送完成后等待一段时间开启接收，等待时间在dwt_setrxaftertxdelay中设置
-
- for(i=0;i<nearbase_num;i++)
- nearbase_distlist[i]=0xffff;
-
+ HAL_GPIO_WritePin(GPIOA, GPIO_PIN_15, GPIO_PIN_RESET);
+ numceshi++;
+ tx_near_msg[TAGCONFIGSUCCESS_INDEX] =0;
+ para_update = 0;
+ get_newbase = 0;
flag_finalsend=0;
+ flag_rxon=1;
+ flag_getresponse=0;
start_count=HAL_LPTIM_ReadCounter(&hlptim1);
recbase_num=0;
- timeout=ceil((float)nearbase_num/4)+2;
- end_count=start_count+(timeout<<5);
+ timeout=nearbase_num*SLOT_SCALE+100; //单位0.1ms
+ end_count=start_count+(timeout<<2);
if(end_count>=32768)
{end_count-=32768;}
mainbase_dist=100000;
mainbase_lost_count++;
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
while(current_count<end_count||current_count>end_count+15000)
+ // while(1)
{
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
{
- if(flag_finalsend)
- {
- dw_systime=dwt_readsystimestamphi32();
- if(dw_systime>temp1&&dw_systime<temp2)
- {
- flag_finalsend=0;
- dwt_forcetrxoff();
- dwt_setdelayedtrxtime(final_tx_time);
- result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- break;
- }
- }
- if(current_count>end_count&¤t_count<end_count+15000)
+// if(flag_finalsend&&flag_ancreadpara)
+// {
+// dw_systime=dwt_readsystimestamphi32();
+// if(dw_systime>temp1&&dw_systime<temp2)
+// {
+//
+// dwt_forcetrxoff();
+// flag_rxon=0;
+// if(flag_ancreadpara) //只有在读取参数的时候需要回复
+// {
+// u16 calCRC;
+// tx_near_msg[MESSAGE_TYPE_IDX] = MBX_PRAAREPLY;
+// memcpy(&tx_near_msg[MESSAGE_PARAREPLY_IDX],g_com_map,SENDANCPARA_LEN);
+// calCRC = CRC_Compute((uint8_t*)g_com_map,SENDANCPARA_LEN);
+// memcpy(&tx_near_msg[MESSAGE_PARAREPLY_IDX+SENDANCPARA_LEN],&calCRC,2);
+// dwt_writetxdata(14+SENDANCPARA_LEN, tx_near_msg, 0);//将发送数据写入DW1000
+// dwt_writetxfctrl(14+SENDANCPARA_LEN, 0);//设定发送数据长度
+//
+// dwt_setdelayedtrxtime(final_tx_time);
+// result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+// }
+// flag_finalsend=0;
+// break;
+// }
+// }
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ if(current_count>=end_count&¤t_count<end_count+15000)
break;
};
if(status_reg==0xffffffff)
@@ -453,19 +505,46 @@
dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
+ test2 = dwt_readcarrierintegrator();
+ poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
+ resp_rx_ts = get_rx_timestamp_u64();
dwt_setrxtimeout(0);//DELAY_BETWEEN_TWO_FRAME_UUS*(nearbase_num+1-recbase_num)+10);//设定接收超时时间，0位没有超时时间
dwt_rxenable(0);//打开接收
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
- { u16 rec_nearbaseid,rec_nearbasepos;
- poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
- resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
+ if (rx_buffer[MESSAGE_TYPE_IDX] == MBX_RESPONSE&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)&&rx_buffer[GROUP_ID_IDX]==group_id) //判断接收到的数据是否是response数据
+ {
+// poll_tx_ts = get_tx_timestamp_u64(); //获得POLL发送时间T1
+// resp_rx_ts = get_rx_timestamp_u64(); //获得RESPONSE接收时间T4
recbase_num++;
memcpy(&rec_nearbaseid,&rx_buffer[ANCHOR_ID_IDX],2);
- if(rec_nearbaseid==mainbase_id)
+ rec_remotepara_state = rx_buffer[MOTORSTATE_INDEX]>>4;
+// TagFreqProcess(rx_buffer[TAGFREQ_IDX]);
+// if(rec_nearbaseid==0x9002)
+// {rec_remotepara_state = rx_buffer[MOTORSTATE_INDEX]>>4;}
+ if(rec_remotepara_state != 0)
+ {
+ para_update = rec_remotepara_state;
+ memcpy(rec_remotepara,&rx_buffer[REMOTEPARA_INDEX],7);
+ if(para_update==2)
+ {
+ flag_ancreadpara = 1;
+ }
+ }
+ if(last_nearbase_num==0)
{
+ get_newbase=1;
+ nearbaseid_list[0]=rec_nearbaseid;
+ nearbase_num=1;
+ memcpy(&tx_near_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
+ }
+ if(rec_nearbaseid==nearbaseid_list[0])
+ {
+ exsistbase_list[0]=KEEP_TIMES;
+ SetANCTimestap(0,&rx_buffer[RESP_MSG_POLL_RX_TS_IDX],&rx_buffer[RESP_MSG_RESP_TX_TS_IDX],resp_rx_ts,&rx_buffer[RESP_MSG_ANC_DISTOFFSET]);
+
//////////////////////////////////时间同步
memcpy(&sync_timer,&rx_buffer[ANCTIMEMS],2);
memcpy(&tmp_time,&rx_buffer[ANCTIMEUS],2);
+ current_count=HAL_LPTIM_ReadCounter(&hlptim1);
// memcpy(&tagslotpos,&rx_buffer[TAGSLOTPOS],2);
tmp_time=tmp_time+450;
if(tmp_time>999)
@@ -475,147 +554,190 @@
if(sync_timer>=1010)
{sync_timer=0;}
}
- // TIM3->CNT=tmp_time;
-// if(tagslotpos>max_slotpos)
-// tagslotpos=tagslotpos%(max_slotpos+1);
-// tyncpoll_time=(tagslotpos-1)*slottime;
- ////////////////////////////
+ rec_nearbasepos=0;
+ exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
+
+ if((rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
+ motor_state=rx_buffer[MOTORSTATE_INDEX]&0xf;
+
+
mainbase_lost_count=0;
flag_finalsend=1;
memcpy(&mainbase_dist,&rx_buffer[DIST_IDX],4);
final_tx_time = (resp_rx_ts + ((RESP_RX_TO_FINAL_TX_DLY_UUS+DELAY_BETWEEN_TWO_FRAME_UUS*nearbase_num+500) * UUS_TO_DWT_TIME)) >> 8;
- temp1=final_tx_time-((350*UUS_TO_DWT_TIME)>>8);
+ temp1=final_tx_time-((850*UUS_TO_DWT_TIME)>>8);
temp2=final_tx_time+((100*UUS_TO_DWT_TIME)>>8);
// dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
final_tx_ts = (((uint64_t)(final_tx_time & 0xFFFFFFFE)) << 8) + TX_ANT_DLY;//final包实际发送时间是计算时间加上发送天线delay
final_msg_set_ts(&tx_near_msg[FINAL_MSG_POLL_TX_TS_IDX], poll_tx_ts);//将T1，T4，T5写入发送数据
final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX], resp_rx_ts);
final_msg_set_ts(&tx_near_msg[FINAL_MSG_FINAL_TX_TS_IDX], final_tx_ts);
- tx_near_msg[MESSAGE_TYPE_IDX]=NEAR_FINAL;
+ tx_near_msg[MESSAGE_TYPE_IDX]=MBX_FINAL;
+ tx_near_msg[GROUP_ID_IDX] = group_id;
+
dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
- usart_send[2] = 1;//正常模式
- usart_send[3] = 17;//数据段长度
- usart_send[4] = frame_seq_nb;//数据段长度
- memcpy(&usart_send[5],&dev_id,2);
- memcpy(&usart_send[7],&rec_nearbaseid,2);
- memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
- usart_send[13] = battary;
- usart_send[14] = button;
- checksum = Checksum_u16(&usart_send[2],17);
- memcpy(&usart_send[19],&checksum,2);
- UART_PushFrame(usart_send,21);
- //result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
+ flag_getresponse=1;
+ memcpy(&rec_tagpos_binary,&rx_buffer[NEARMSG_EMPTYSLOTPOS_INDEX],4);
}else{
rec_nearbasepos=FindNearBasePos(rec_nearbaseid);
- final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], resp_rx_ts);
- memcpy(&nearbase_distlist[rec_nearbasepos],&rx_buffer[DIST_IDX],4);
+ SetANCTimestap(rec_nearbasepos,&rx_buffer[RESP_MSG_POLL_RX_TS_IDX],&rx_buffer[RESP_MSG_RESP_TX_TS_IDX],resp_rx_ts,&rx_buffer[RESP_MSG_ANC_DISTOFFSET]);
+
+ if(rec_nearbasepos>=last_nearbase_num) //发现新的基站
+ {
+ get_newbase=1;
+ nearbase_num++;
+ nearbaseid_list[rec_nearbasepos] = rec_nearbaseid;
+ memcpy(&tx_near_msg[ANCHOR_ID_IDX],&rec_nearbaseid,2);
+ }
+
+ exsistbase_list[rec_nearbasepos]=KEEP_TIMES;
+
+
+ if(motor_state<(rx_buffer[MOTORSTATE_INDEX]&0xf)&&(rx_buffer[MOTORSTATE_INDEX]&0xf)!=3)
+ {
+ motor_state=rx_buffer[MOTORSTATE_INDEX];
+ }
+ final_msg_set_ts(&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos)*4], resp_rx_ts);
+
dwt_writetxdata(28+nearbase_num*4, tx_near_msg, 0);//将发送数据写入DW1000
dwt_writetxfctrl(28+nearbase_num*4, 0);//设定发送数据长度
- LED0_BLINK;
- usart_send[2] = 1;//正常模式
- usart_send[3] = 17;//数据段长度
- usart_send[4] = frame_seq_nb;//数据段长度
- memcpy(&usart_send[5],&dev_id,2);
- memcpy(&usart_send[7],&rec_nearbaseid,2);
- memcpy(&usart_send[9],&rx_buffer[DIST_IDX],4);
- usart_send[13] = battary;
- usart_send[14] = button;
- checksum = Checksum_u16(&usart_send[2],17);
- memcpy(&usart_send[19],&checksum,2);
- UART_PushFrame(usart_send,21);
-
- //dwt_setdelayedtrxtime(final_tx_time);//设置final包发送时间T5
- // result=dwt_starttx(DWT_START_TX_DELAYED);//设定为延迟发送
- //dwt_writetxdata(4,&tx_near_msg[FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4], FINAL_MSG_RESP_RX_NEARBASE_IDX+(rec_nearbasepos+1)*4);//将发送数据写入DW1000
}
}
- }
+ }else{
dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
- current_count=HAL_LPTIM_ReadCounter(&hlptim1);
+ if(flag_rxon)
+ {dwt_rxenable(0);
+ }
+ }
+ // dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
}
- if(mainbase_lost_count>5)
+ dwt_forcetrxoff();
+ dwt_write32bitreg(SYS_STATUS_ID,SYS_STATUS_RXFCG| SYS_STATUS_ALL_RX_ERR);
+ CalculateDists();
+ j = 0;
+ next_nearbase_num = 0;
+ for(i=0;i<nearbase_num;i++)
{
- tag_state=DISCPOLL;
- }
- NearAncSelect();
- if(recbase_num<MIN_ANCHOR_NUM )
- {
- anclost_times++;
- if(anclost_times>3)
- {
- tagslotpos=poll_tx_ts%(max_slotpos+1);
+ if(exsistbase_list[i]>0)
+ {
+ exsistbase_list[i]--;
+ next_nearbase_num++;
+ true_exsistbase_list[j]=exsistbase_list[i];
+ true_nearbase_idlist[j]=nearbaseid_list[i];
+ true_nearbase_distlist[j++]=nearbase_distlist[i];
+
}
- }else{
- anclost_times=0;
}
-
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR);
-
-
+ nearbase_num = next_nearbase_num;
+ if(mainbase_lost_count>1)//&&exsistbase_list[0] != 0)
+ {
+ last_lpcount-= HAL_LPTIM_ReadCounter(&hlptim1)%(g_com_map[COM_INTERVAL]*16);
+ }
+ last_nearbase_num = next_nearbase_num;
+ for(i=0;i<last_nearbase_num-1;i++)
+ {
+ for(j=0;j<last_nearbase_num-1;j++)
+ {
+ if(true_nearbase_distlist[j]>true_nearbase_distlist[j+1])
+ {
+ u32 temp_dist,temp_id,temp_exsis;
+ temp_dist=true_nearbase_distlist[j];
+ temp_id = true_nearbase_idlist[j];
+ temp_exsis=true_exsistbase_list[i];
+ true_nearbase_distlist[j]=true_nearbase_distlist[j+1];
+ true_nearbase_idlist[j]=true_nearbase_idlist[j+1];
+ true_exsistbase_list[j]=true_exsistbase_list[j+1];
+
+ true_nearbase_distlist[j+1]=temp_dist;
+ true_nearbase_idlist[j+1]=temp_id;
+ true_exsistbase_list[j+1]=temp_exsis;
+ }
+ }
+ }
+
+ report_num=0;
+ for (i=0;i<last_nearbase_num;i++)
+ {
+ nearbaseid_list[i]=true_nearbase_idlist[i];
+ nearbase_distlist[i]=true_nearbase_distlist[i];
+ exsistbase_list[i] = true_exsistbase_list[i];
+ }
+
+ dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_ALL_RX_ERR| SYS_STATUS_TXFRS |SYS_STATUS_RXFCG);
+//HAL_GPIO_WritePin(LED0_GPIO, GPIO_PIN_9, GPIO_PIN_RESET);
+
+if(para_update==1)
+ {
+ uint16_t calCRC;
+ calCRC = CRC_Compute(rec_remotepara,5);
+ if(memcmp(&calCRC,&rec_remotepara[5],2)==0)
+ { uint8_t pack_msgtype,pack_index,pack_length;
+ pack_msgtype = rec_remotepara[0];
+ pack_index = rec_remotepara[1];
+ pack_length = rec_remotepara[2];
+ if(pack_msgtype==2)
+ {
+ if( pack_index == 1)//MOTOR_ONTIME_INDEX)
+ {
+
+ // motor_keeptime = rec_remotepara[3];
+ }else if(pack_index == CNT_UPDATE)
+ {
+ if(rec_remotepara[3]==2)
+ {
+ EnterUWBUpdateMode();
+ }
+ }
+ else{
+ if(pack_index<200)
+ {
+ memcpy((uint8_t*)&g_com_map + pack_index, &rec_remotepara[3], pack_length);
+ //返回一个error状态
+ //SendComMap(pack_datalen,pack_index);
+ save_com_map_to_flash();
+ delay_ms(100);
+ NVIC_SystemReset();
+ }
+ }
+ }
+ }
+ }
}
-
-void GetNearMsg(void)
-{
- u32 start_poll,frame_len;
- memcpy(&tx_near_msg[ANCHOR_ID_IDX],&mainbase_id,2);
- memcpy(&tx_near_msg[TAG_ID_IDX],&dev_id,2);
- tx_near_msg[MESSAGE_TYPE_IDX] = NEAR_MSG;
-
- dwt_setrxaftertxdelay(POLL_TX_TO_RESP_RX_DLY_UUS); //设置发送后开启接收，并设定延迟时间
- dwt_setrxtimeout(RESP_RX_TIMEOUT_UUS);
- dwt_writetxdata(12, tx_near_msg, 0);//将Poll包数据传给DW1000，将在开启发送时传出去
- dwt_writetxfctrl(12, 0);//设置超宽带发送数据长度
- dwt_starttx(DWT_START_TX_IMMEDIATE| DWT_RESPONSE_EXPECTED);
-
- /* We assume that the transmission is achieved correctly, poll for reception of a frame or error/timeout. See NOTE 8 below. */
- while (!((status_reg = dwt_read32bitreg(SYS_STATUS_ID)) & (SYS_STATUS_RXFCG | SYS_STATUS_ALL_RX_ERR)))//不断查询芯片状态直到成功接收或者发生错误
- {
- };
- if(status_reg==0xffffffff)
- {
- NVIC_SystemReset();
- }
- if (status_reg & SYS_STATUS_RXFCG)//如果成功接收
- {
- dwt_write32bitreg(SYS_STATUS_ID, SYS_STATUS_RXFCG | SYS_STATUS_TXFRS);//清楚寄存器标志位
- frame_len = dwt_read32bitreg(RX_FINFO_ID) & RX_FINFO_RXFLEN_MASK; //获得接收到的数据长度
- dwt_readrxdata(rx_buffer, frame_len, 0); //读取接收数据
- if (rx_buffer[MESSAGE_TYPE_IDX] == NEAR_MSG&&!memcmp(&rx_buffer[TAG_ID_IDX],&dev_id,2)) //判断接收到的数据是否是response数据
- {
- nearbase_num=rx_buffer[NEARBASENUM_INDEX];
- tagslotpos=rx_buffer[TAGSLOTPOS];
- memcpy(nearbaseid_list,&rx_buffer[NEARBASEID_INDEX],nearbase_num*2);
- slottime=ceil((nearbase_num+2)*0.3)+1;
- tyncpoll_time=tagslotpos*slottime;
- tag_state=NEARPOLL;
- }
- }
-}
-
+u8 regpoll_count;
+u32 id;
void Tag_App(void)//发送模式(TAG标签)
{
+
//LED0_ON;
- dwt_forcetrxoff();
+ id = dwt_readdevid() ;
+ while (DWT_DEVICE_ID != id)
+ {
+ u8 iderror_count = 0;
+ id = dwt_readdevid() ;
+ if(iderror_count++>100)
+ {
+ printf("UWB芯片ID错误");
+ break;
+ }
+ }
+ delay_us(100);
g_Resttimer=0;
- switch(tag_state)
- {
- case DISCPOLL:
- Poll();
- break;
- case GETNEARMSG:
- // if(trygetnearmsg_times--!=0)
- {GetNearMsg();
- }
-// else{
-// tag_state=DISCPOLL;
-// }
-
- break;
- case NEARPOLL:
- //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_SET);
- NearPoll();
- //GPIO_WriteBit(EU_TX_GPIO, EU_RX_PIN, Bit_RESET);
- break;
- }
+// if(freqlost_count>FREQ_LOST_TIME)
+// {
+// if(regpoll_count++>11) //待机状态1分钟上传一次基站状态
+// {
+// regpoll_count = 0;
+// Registor_Poll();
+// }
+// }else{
+// if(regpoll_count++>59)//测距状态1分钟上传一次基站状态
+// {
+// regpoll_count = 0;
+// Registor_Poll();
+// }
+// }
+ NearPoll();
+ dwt_entersleep();
+ bat_percent=Get_VDDVlotage();
}
--
Gitblit v1.9.3